AERMEC S.p.A. reserves the right to make any modifications considered necessary to improve its products at any moment and is

not obliged to add these modifications to machines that have already been fabricated, delivered or are under construction.

...20

16.

Procedures for the realisation of the cooling lines

...21

17. Cooling lines connection layout..............................22

20.4. Three-way valve ........................................................26

20.5. Installation of auxiliary device (gate controller) ....26

22. Hbi wt/wts electric connections: .............................29

23. Electric wiring .............................................................30

24. Wiring diagram ..........................................................31

25. Wiring diagram .........................................................34

26. Information regarding terminal boards ..................37

27. Unit debug .................................................................38

28. Functioning and daily maintenance ......................40

tions. Designed for air conditioning and the production of

domestic hot water (DHW), it must be destined to this use

compatibly with the performance features. Any contractual

or extracontractual liability of the Company is excluded for

injury/damage to persons, animals or objects owing to

installation, regulation and maintenance errors or improper

use. All uses not expressly indicated in this manual are

The appliance must be installed in such a way as to enable

maintenance and/or repairs to be carried out.

The appliance warranty does not cover the costs for ladders,

scaffolding, or other elevation systems that may become nec-

essary for carrying out servicing under warranty.

Do not modify or tamper with the chiller as dangerous situa-

tions can be created and the manufacturer will not be liable

for any damage caused. The validity of the warranty shall be

void in the event of failure to comply with the above-men-

tioned indications.

AERMEC will not assume any responsibility for damage due

to failure to follow these instructions.

Before beginning any operation, READ THESE INSTRUCTIONS

CAREFULLY AND CARRY OUT THE SAFETY CHECKS TO AVOID

ALL RISKS. All the staff involved must have thorough knowl-

edge of the operations and any dangers that may arise at

the moment in which the installation operations are carried

The HBI units are manufactured with attention to the

individual components in a way to protect both the user and

This instruction manual, along with the user manual, is an

integral part of the product: make sure that it always accom-

panies the appliance, even if transferred to other owners or

user or is transferred to another system.

It is recommended that the installer instructs the user

regarding appliance functioning and fundamental Safety

The HBI heat pump must be intended for the use for which it

has been expressly manufactured.

−Test

−Low noise

−Emergency control

− Instant hot water

(for DHW use)

Cooling: in this mode, the indoor unit

supplies cooled water (to the system, to

the fan coils) in a way to allow heat ex-

change, cooling the room temperature

Heating: in this mode, the indoor unit

in a way to allow heat exchange, heat-

ing the room temperature

Heating of DHW:

it is the specifi c mode

The cooling or heating modes can

be combined with the production of

domestic hot water; naturally, if these

combined modes are used, the system

will assign a priority to the system/domes-

tic requests, on the basis of which the

system will satisfy fi rst one and then the

ATTENTION: the default settings envi-

sion that the priority is assigned to the

ATTENTION: refer to the user manual in

order to modify the default settings

Every functioning mode allows to set

different specifi c functions (as well as

switch-on/off of the unit and setting the

work set-points); these functions are:

Allows to check the correct functioning

produced when the machine is running.

If the unit has been stopped by an alarm

or malfunctioning, this function allows to

reach the hot water production set-point

(both system and for production of DHW)

only using the electric resistances present

in the system (HBI indoor unit, HBI WT/

electric resistance inside the HBI WT/WTS

storage tank (ATTENTION: the use of this

function increases the absorption of cur-

rent in the system)

This function allows to maintain the room

temperature parameter (room air sensor

mandatory) within a determined safety

threshold in order to prevent the room

The unit is supplied with a timer via which

it is possible to perform different opera-

tions linked to hourly programming; these

functions are:

• Daily timer;

• Timer with countdown;

• Holiday timer;

This function allows the unit (on the basis

of the user settings) to automatically

calculate the temperature to apply to

the room; this function bases its function-

ing on the room air temperature and it is

therefore necessary to use the room air

sensor in order to operate this function.

The table below gives the compatibility

between functioning mode and the

ATTENTION: The HBI unit is set by default on cooling or heating priority

Chiller connection Connections

1 Liquid side service valve 3/8"

2 Gas side service valve 5/8"

11. GUIDE LINES FOR INSTALLATION OF THE INDOOR UNIT

Respecting minimum technical

spaces in order to allow the pas-

sage of air and any maintenance

to be performed.

Manometer on

the machine

Pressure limit 3bar

To access the electric box, remove the screws

The unit does not have a

cut-off valve or system drai-

ning unit.

It is necessary to envision

installation. Assembly is

recommended in order to

below the maximum. (With the aid of the figure

The expansion vessel is too small and regulation

cannot be performed.

must be regulated to guarantee suitable functioning.

necessary.

The minimum total volume of the water is 20 litres.

tifi ed installer.