Samsung SCC-C7325 User manual

10x Mini Smart

Dome Camera

user manual

SCC-C6323P

SCC-C6325P

SCC-C7325P

imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service,

please register your product at

www.samsungsecurity.com

ENG FRE

GER SPA

ITA

2 – 10X MINI SMART DOME CAMERA

Safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL..

This symbol indicates high voltage is present inside. It is dangerous to make any kind of

contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has

been included with this product.

WARNING

To prevent damage which may result in ﬁ re or electric shock hazard, do not expose this appliance to rain or

moisture.

WARNING

Be sure to use only the standard adapter that is speciﬁ ed in the speciﬁ cation sheet. Using any other adapter

could cause ﬁ re, electrical shock, or damage to the product

Incorrectly connecting the power supply or replacing battery may cause explosion, ﬁ re, electric shock, or

damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat

generation or ﬁ re.

Securely plug the power cord into the power receptacle. Insecure connection may cause ﬁ re.

When installing the camera, fasten it securely and ﬁ rmly. A falling camera may cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers ﬁ lled with water

on top of the camera. Doing so may cause personal injury due to ﬁ re, electric shock, or falling objects.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁ re or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately

disconnect the power source and contact the service center. Continued use in such a condition may cause

ﬁ re or electric shock.

If this product fails to operate normally, contact the nearest service center. Never disassemble or modify

this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modiﬁ cations or

attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁ re or electric shock.

If the camera is installed or rebooted after power failure when ambient temperature is below the freezing point,

the dome cover is frosted. In this case, the frost will be disappeared after 3 hours after turning on the power.

(It is noted that lowest guaranteed operating temperature is -45º C (-49º F) without wind.)

•

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

C

1

2

3

4

5

6

7

8

9

English – 3

ENG

Safety information

CAUTION

Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to

excessive vibrationor magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high

humidity. Doing so may cause ﬁ re or electric shock.

If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall

it.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so may cause ﬁ re or

damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁ re.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the

CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁ lled with liquids, such as vases,

shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at any time.

1.

2.

3.

4.

5.

6.

7.

8.

9.

4 – 10X MINI SMART DOME CAMERA

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including ampliﬁ ers) that

produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or

the third prong is provided for your safety. If the provided plug does not ﬁ t into your outlet, consult an electrician

for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁ ed by the manufacturer.

Use only with cart, stand, tripod, bracket, or table speciﬁ ed by the manufacturer, or sold

with the apparatus.

Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

combination to avoid injury from tip-over.

Refer all servicing to qualiﬁ ed service personnel. Servicing is required when the apparatus has been damaged in

any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

English – 5

ENG

Contents

Introduction

Features 7

Product & Accessories 8

Parts Name & Functions 10

Installation

DIP Switch Setup 13

Installation using Surface mount on the Ceiling 14

Installation using Ceiling Mount Bracket (SCC-C7325) 16

Installation using Wall Mount Bracket (SCC-C7325) 17

Cabling 19

Operation

Check points before operation 21

Preset and Pattern Function Pre-Check 21

Starting OSD Menu 21

Reserved Preset 21

Preset 22

Auto Pan 22

Pattern 22

Scan 23

Schedule 23

Other Functions 23

OSD Display of Main Screen 24

General Rules of Key Operation for Menu 25

Main Menu 25

System Information 25

Display Setup 25

6 – 10X MINI SMART DOME CAMERA

F

❖

How to use OSD Menu

Privacy Zone Mask Setup 26

Motion Setup 26

Function Setup 27

PRESET Setup 28

Auto Pan Setup 29

Pattern Setup 30

Scan Setup 30

Schedule Setup 32

Camera Setup 33

System Setup 34

System Initialize 36

Speciﬁ cations

Speciﬁ cations 38

Dimension 41

Contents

English – 7

ENG

Introduction

FEATURES

Camera Speciﬁ cations

CCD Sensor : 1/4” Interline Transfer CCD

Zoom Magniﬁ cation : x10 Optical Zoom, x10

Digital Zoom (Max x 100 Zoom)

Day & Night Function

Various Focus Mode: Auto-Focus / Manual Focus

/ Semi-Auto Focus.

Independent or General Camera Characteristic

Setup in Preset operation

Powerful Pan/Tilt Functions

Max. 360°/sec high speed Pan/Tilt Motion

Using Vector Drive Technology, Pan/Tilt motions

are accomplished in a shortest path. As a result,

time to target view is reduced dramatically and the

video on the monitor is very natural to watch.

For jog operation using a controller, since ultra

slow speed 0.05°/sec can be reached, it is very

easy to locate camera to desired target view.

Owing to zoom-proportional pan/tilt speed,

camera can be moved to a desired position in

accurate manner even though zoom ratio is high.

Preset, Pattern, Auto Pan, Scan, Privacy

Mask, Schedule and More…

MAX. 127 Presets are assignable and

characteristics of each preset can be set up

independently, such as White Balance, Auto

Exposure, Label and so on.

Max. 8 Auto Pan can be stored. This enables to

move camera repetitively between two preset

positions with designated speed.

Max. 4 of Patterns can be recorded and

executed. This enables for camera to track a

surveillance trajectory as closely as possible which

are recorded from operator’s motion of joystick.

Max. 8 Scan can be stored. To compose a

surveillance trajectory, the Group can have max.

20 entities of Preset/Pattern/Scan functions. This

enables for camera to move a combinations of

those functions repetitively.

Max. 4 Masks are settable independently to

protect privacy zone. The mask is arbitrary-sized

rectangular and locate any location in view space.

❖

•

❖

•

❖

•

7 rules of Schedule can be assigned by day and

time. Appropriate actions (such as Home, Preset,

Auto Pan, Pattern, Scan) can be deﬁ ned for each

rule. Also, it is possible to make rule by Weekday

and Allday to simplify the rule.

PTZ(Pan/Tilt/Zoom) Control

With RS-485 communication, max. 255 of

cameras can be controlled at the same time.

Pelco-D/ Pelco-P, Samsung protocol can be

selected as a control protocol in the current

version of ﬁ rmware.

OSD(On Screen Display) Menu

OSD menu is provided to display the status

of camera and to conﬁ gure the functions

interactively.

Currently, 7 Languages are supported for

OSD Menu: [ENGLISH/ESPAÑOL/FRANÇAIS/

DEUTSCH/ITALIANO/РУССКИЙ/PORTUGUÊS]

The information such as Camera ID, Pan/Tilt/

Zoom/Direction, Alarm Input & Output, date/time,

current temperature and Preset can be displayed

on screen.

Each display item can be turned On or Off

independently.

Alarm I/O Functions

2 alarm sensor Inputs and 1 relay output are

available.

To reject external electric noise and shock

perfectly, alarm sensor Input is decoupled with

photo coupler.

If an external sensor is activated, camera can be

set to move to the corresponding Preset position.

Relay output can be assigned to work with a

certain preset.

Reserved Presets for Special Purpose

Besides regular 127 presets, direct calling of

reserved presets enables to set up many of

camera functions with without using OSD menu.

For more information, refer to “Reserved Preset” in

this manual.

•

❖

•

❖

•

❖

•

❖

•

8 – 10X MINI SMART DOME CAMERA

Introduction

PRODUCT & ACCESSORIES

Product & Accessories (SCC-C6323)

Main Product

Accessory

❖

•

Main Body Surface Mount Bracket

Product & Accessories (SCC-C6325)

Main Product

Accessory

❖

•

Main Body Surface Mount Bracket



Screw & Plastic

Anchor (4Pcs)

❖

Terminal Block Torx Screw Driver Surface Mount

Gasket

Manual

Mount Bracket Option : Please use SADT-937WM for this purpose.Ú

G

Screw & Plastic Anchor (4Pcs)

Manual

Core ﬁ lter (PAL Option)

English – 9

ENG

Introduction

Product & Accessories (SCC-C7325)

Main Product

Accessory

Mount Bracket Option

❖

•

Main Body Sun Shield Housing



Terminal Block

Torx Screw Driver Manual

Ceiling Mount Bracket (SADT-732CM)Wall Mount Bracket (SADT-732WM)

10 – 10X MINI SMART DOME CAMERA

Introduction

PARTS NAME & FUNCTIONS

SCC-C6323❖

Main Unit / Surface Mount Bracket Back of Main Unit



Surface Mount Bracket

This is used to install the camera directly on the

ceiling. After separating this cover ﬁ rst and then

attach this directly to ceiling. Camera must be

assembled at the last stage.

Do not use this bracket when installing camera on

the wall with wall mount bracket or on the ceiling with

ceiling mount bracket.

Separating Slit

Using a coin, you can separate upper part lower

body of the dome.

•

Dome Cover

Do not detach protection vinyl from dome cover

before ﬁ nishing all installation process to protect

dome cover from scratches or dust.

DIP Switch

Adjusts camera ID and protocols.

Cable Duct

When you want to install the camera on the surface

of hard ceiling, you need to handle the cable through

side of the dome. In this case, break the side wall bit

and make the cable pass through the cable duct.

•

❖

Surface Mount Bracket

Dome Cover

Separating Slit

DIP Switch

Cable Duct

English – 11

ENG

Introduction

SCC-C6325❖

Dome Cover

Do not remove the protection vinyl from dome cover

before ﬁ nishing all installation process to protect

dome cover from scratches or dust.

Surface Mount Bracket

This is used to install the camera directly on the

ceiling. After separating this cover, mount this

bracket on to ceiling. Main body of the camera is

going to be assembled again in the last stage.

Do not use this bracket with wall mount bracket or

ceiling mount bracket.

•

Lockup Screw

Fixes main unit brackets like surface, wall, and

ceiling.

Cabling Terminal Block

During installation, Power, Video, Communication,

Alarm Input cables are connected on to this cabling

terminal block.

DIP Switch

Adjusts camera ID and protocols.

•

Main Unit / Surface Mount Bracket Back of Main Unit

Surface Mount Bracket

Mounting Hole

Main Body

Dome Cover

Lockup Screw



Cabling Terminal

Block

DIP Switch

12 – 10X MINI SMART DOME CAMERA

Introduction

D

B

s

c

❖

PARTS NAME & FUNCTIONS

SCC-C7325❖

Dome Cover

Do not remove the protection vinyl from dome cover

before ﬁ nishing all installation process to protect

dome cover from scratches or dust.

Sun Shield Housing

Lockup Screw

Fixes main unit brackets like surface, wall, and

ceiling.

•

Cabling Terminal Block

During installation, Power, Video, Communication,

Alarm Input cables are connected on to this cabling

terminal block.

DIP Switch

Adjusts camera ID and protocols.

•

Main Unit / Surface Mount Bracket Back of Main Unit

Sun Shield Housing

Main Body

Dome Cover

Lockup Screw

Cabling Terminal

Block

DIP Switch

English – 13

ENG

Installation

DIP SWITCH SETUP

Before you install the camera, you should set the DIP

switches to conﬁ gure the camera ID, Baud rate, and

communication protocol.

Camera ID Setup

ID number of camera is set using binary number.

The example is shown bellow.

Pin 12345678

ID Value 1 2 4 8 16 32 64 128

ex) ID=5

ex) ID=10

on

off

on

off

on

off

The range of ID is 0~255. Factory default of

Camera ID is 1.

If you want to control a certain camera, you must

match the camera ID with Cam ID setting of DVR

or Controller.

Communication Protocol Setup

❖

•

❖

Select the appropriate Protocol with DIP switch

combination.

Switch State

Protocol

Pin1 Pin2 Pin3 Pin4

OFF OFF OFF OFF Auto Protocol

ON OFF OFF OFF Pelco-D

OFF ON OFF OFF Pelco-P

ON ON OFF OFF Samsung

If you set the protocol as Auto Protocol, camera

will automatically recognize the kind of Protocol.

Auto Protocol supports Pelco-D and Samsung Protocol.

If you want to control using DVR or system

keyboard, their protocol must be identical to

camera. Otherwise, you can not control the camera.

If you changed camera protocol by changing DIP S/W,

the change will be effective after you reboot the camera.

Factory default of protocol is “Auto Protocol

Communication Baud rate Setup

Select the appropriate Baud rate with DIP switch

combination.

Switch State

Protocol

Pin5 Pin6 Pin7

OFF OFF OFF 2400 BPS

ON OFF OFF 4800 BPS

OFF ON OFF 9600 BPS

ON ON OFF 19200 BPS

OFF OFF ON 38400 BPS

Factory default of Baud rate is “9600 BPS”

•

❖

•



123456

ON

78



123456

ON

78

Protocol

Buad Rate

Auto Select

RS-485

Terminate

ID Setting (1~255)

14 – 10X MINI SMART DOME CAMERA

Installation

RS-485 Termination Resistor

Pin 8 is used for ON/OFF of RS-485 Termination.

Normally, it must be OFF state. Especially when

you have trouble with long Daisy chain style

connection, turn ON this termination switch of last

camera.

Pin 8 RS-485 Termination Resistor (On/Off)

INSTALLATION USING SURFACE

MOUNT ON THE CEILING

SCC-C6323

① Setup DIP Switch (see previous page).

② Screw surface mount bracket to ceiling with 4

screws.

❖

•

–

❖

③ Placing lower body to Surface Mount bracket.

The cable must be properly handled into hole of

bracket or side of lower body.

④ Make sure stopper pin of bracket pin is located

the rightmost side of lower body groove as

shown in the picture. Press the dome and turn

clockwise till the pin is located leftmost side

of groove. Detach protection vinyl from dome

cover.

123456

ON

78



G



English – 15

ENG

Installation

⑤ Tighten locking screw.

⑥ Connect Video, communication, power cable

properly. (see next section)

SCC-C6325

① To pass cables to upside of ceiling, please,

make about ũ60mm hole on the ceiling panel.

② Screw surface mount bracket to ceiling with

4 screws.

③ Wire cables to terminal block and connect the

terminal blocks to main unit.

❖

16 – 10X MINI SMART DOME CAMERA

Installation

④ Screw main unit to surface mount bracket with

4 lock-up screws.

⑤ Detach protection vinyl from dome cover.

INSTALLATION USING CEILING

MOUNT BRACKET (SCC-C7325)

① Install ceiling mount bracket on the ceiling using

4 screws provided.

② Turn sunshield clockwise after locating it in the

pipe head of ceiling mount properly.

English – 17

ENG

Installation

③ After wiring cables to terminals, plug the

terminals into the bottom of main unit. Then, ﬁ x

the main unit with sunshield with 4 screws.

④ Detach protection vinyl from dome cover.

INSTALLATION USING WALL

MOUNT BRACKET (SCC-C7325)

① Use the 4 screws (provided) to secure the wall

mount bracket to the wall.

② Turn sunshield clockwise after locating it in the

pipe head of wall mount properly.

18 – 10X MINI SMART DOME CAMERA

Installation

③ After wiring cables to terminals, plug the

terminals into the bottom of main unit. Then, ﬁ x

the main unit with sunshield with 4 screws.

④ Detach protection vinyl from dome cover.

C

English – 19

ENG

Installation

CABLING

SCC-C6323❖

Dual Voltage

DC 12V/AC 24V

BNC Video

1 (Black) : IN COM

2 (Yellow) : IN 1

3 (Brown) : IN 2

4 (Red) : Relay Out

5 (Orange) : Relay Out

Controller/DVR

IrDA

Sensor

Door

Switch

Sensors

Lamp

Relay Out

Cabling Terminal Block

SCC-C6325/ SCC-C7325❖

Dual Voltage

DC 12V/AC 24V

Controller/DVR

BNC Video

Relay Out

IrDA

Sensor

Door

Switch

Sensors

Lamp

Relay Out

Attaching the Core ﬁ lter

To reduce interference of electric wave. attach the core ﬁ lter to BNC Cable (PAL Option)

Attach the core ﬁ lter closer to the jack of the product.

Wind once!

BNC Cable ( PAL Option)

* Note: To attach the core ﬁ lter to BNC Cable, roll the cable over core ﬁ lter once.

* Note: Be careful not to damage the cable when attaching the core ﬁ lter.

❖

•

20 – 10X MINI SMART DOME CAMERA

Installation

Power Connection

Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back of

main unit.

Power Mode

Input Voltage Range

Power Consumption

C6323/ C6325 C7325

DC 12V DC 11V ~ 15V 8 W

12W

AC24V AC 20V ~ 29V 10W

21W

RS-485 Communication

For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-485

communication lines of them is connected in parallel as shown below.

❖

•

❖

•

Video Connection

Connect with BNC coaxial cable.

Alarm Input Connection

Sensor Input

 It is noted that short circuit between GND and

Input pin means alarm activation.

❖

•

❖

•

If you want to use Alarm Input, the types of sensor

must be selected in OSD menu. The sensor types

are Normal Open and Normal. If sensor type is

not selected properly, the alarm can be activated

reversely.

Normal Open

(N.O)

Sensor output is turned ON when

sensor is activated

Normal Close

(N.C)

Sensor output is turned OFF when

sensor is activated

Relay Output

There are 4 Alarm Outputs and all of them are Relay

contact type. Therefore, you do not have to care about

polarity, AC/DC, and isolations between channels. Care

must be taken for the power capacity of relay contact

written above.

•

C

P

F

A

S

R

Keyboard Controller DVR



IN1

IN2

IN COM

INTERNAL

Internal

Relay Out

Power

Relay Out

Page is loading ...

Samsung SCC-C7325 User manual

Samsung SCC-C7325 User manual

in other languages

Related papers

Other documents