Assa Abloy ENA-BX User manual

Wirefree Yale ENA-BX

External Siren

Feature:

1. Learn button

2. Tamper Spring

3. Power On/Off switch

4. Dip Switch Block

5. Strobe Lights

6. Sounder

7. Siren ﬁxing holes (x4)

8. Battery compartment screws (x4)

9. DC power terminal block

10. Strobe window

11. Lid ﬁxing screw

Pack content:

1x External Siren

4x Screws

4x Wall Plug

Dip Switch (SW) function table

Dip SW 1 Clear Siren memory

ON Clear

OFF Normal (Default)

Dip SW 2 Interference detection

ON Enable

OFF Disable (Default)

Dip SW 3 Supervision

ON Enable

OFF Disable

Dip SW 4 Function not used. Dip switch

must be in the off position.

Notes:

• DonotslidealltheswitchestotheON

 positionsimultaneously.Doitoneata

 time.

• Ifsupervisionisenabledinthecontrolpanel,

 DipSw3mustbeturnedOn(Enable)orelse

 the“SupervisionFail”faultwillbeshown.

OFF

1 2 3 4

SmartHome Alarm series

Programming

Step 1.Removethesirenfrontcover.

Step 2.MakesuretheDipSwitch#4issettothe

OFFposition.Alsosetthepowerswitchofthesiren

totheONposition.

Step 3.LogintotheControlPanel’sEngineering

menu.Select“ZoneSettings”->“ZoneCong”->

“AddZone”.PressOKandtheLCDoftheControl

Panelwilldisplay“*Pushbuttonon*Devicetoadd”.

Step 4.Press&holdthesiren’sLearnbuttonfor1

second.Thesirenwillbeeponce,withtheLED#1

(Left)andLED#3(Right)ashingoncetoindicate

the“learnsignal”hasbeentransmitted.

NOTE

ToexitLearnMode:PresstheLearnbuttonagain,

or,Sirenwillautomaticallyexitafter3minutes

(time-out).ThesirenwillbeeponceandtheLED#2

(Middle)willashoncetoindicatethishadtaken

place.

Step 5.Ifsuccessfullyreceived,theControlPanel

willdisplay“Detected(OK?)”.PressOKtoconrm

thelearning.Thecontrolpanelwillnowsendalearn

acknowledgementtothesiren.

Step 6.OncethesirenreceivestheLearn

acknowledgementfromtheControlPanel,itwill

emitashortbeepwithLED#2ashingonceto

indicatethatthesirenhasbeensuccessfullyadded

intothesystem.Youcannowproceedtosetup

parametersforthesiren(Pleasewaitforatleast7

secondsbeforeproceeding).

Step 7. Toprogramsirenparameters,pressthe

“Return”buttonontheControlPaneltoreturnto

theroot.Select“ZoneSettings”->“ZoneCong”->

“EditExt.Siren”option.

The following settings are applied to all sirens in

the system:

“Siren Length”

Press ▲or▼toincreaseordecreasethesiren

lengthfromDisableor1to30minutes(at1minute

increments).PressOKtoselect,thesirenwillbeep

oncetoindicateconrmation.

“Siren Offset”

AdjustthelengthofSilentDelayonsirenringing

afteranalarmeventisdetected.Thisallowsthe

controlpaneltoreporttheeventinsilencevia

telephonepriortoaloudalarmevent.Press▲

or▼toincreaseordecreasethesirendelaytime

fromDisableor10to60seconds(at10second

increments).

“Conﬁrm Sound”

Notifyusersofthesystemstatusviasirenbeeps.One

beepforarmandtwobeepsfordisarm.SelectEnable

orDisabletoenableordisablethisfunction.

“Entry Sound”

Notifyusersoftheentrycountdownviasirenbeeps.

SelectEnableorDisabletoenableordisablethis

function.

“Siren Tamper”

Oncethetamperprotectionisdisabled,thesirenwill

automaticallyreverttoenableafteranhour(ifuserhas

notalreadyenableditmanually).

“Comfort LED”

Controlthesiren’sLEDashintervalduringnon-

alarmmode.Press▲or▼toincreaseordecrease

theashintervaltimefromDisableor5,10to60

seconds(at10secondsincrements).Pleasenotethat

enablingthisfeaturewilldecreasethesiren’sbattery

life.

Step 8:Tondthebestinstallationlocationforthe

sirenyouwillneedtousethe“walktest”option.

Accessthisoptionfrom“Testing”->“WalkTest”.

Step 9:Holdthesireninthedesiredlocation,press

theTest/Learnbuttontoconrmifthislocationis

withinradiosignalrangeoftheControlPanel.The

RSSIsignalstrengthvaluewillbedisplayedonthe

controlpanel,rangingfrom0~9(9indicatesthebest

signalstrengthperformance).Donotinstallsireninan

areawheretheRSSIvalueislessthan5.

Step 10.Keeppressingthe“Return”keytoexit

programmingmenuinthecontrolpanel.TheLEDswill

ash2fullcyclestoindicatethattheuserhasexited

theprogrammingmenusuccessfullyandthatthe

systemisinStandbymode.

Step 11.Theparametersareallsetandthesirenis

readytobemounted.

Mounting

Therearetwotamperspringsonthesiren(please

seeimageontherstpageforTamperlocation).Ifthe

sirenispulledofffromthewalland/orseparatingits

front&backcover,thealarmwillbeactivated.Please

ensureitisfullydepressedwhenthesirenismounted.

Step 1.Disablethesirentamperusingthecontrol

panel.Select“ZoneSettings”->“ZoneCong“->

“EditExt.Siren”->“SirenTamper”.Thisoptionneeds

tobedisabled.

Step 2.Removethesirencover.Usingthescrews

andwallplugsprovided,mountthebaseunitonthe

wallthroughthe4xmountingholes.Carefullyalign

theholeswhendrilling.

Step 3.EnsurethePowerSwitchisswitchedto

theONposition.Replacethesirencover.

Step 4.Enablethesirentamperusingthecontrol

panel.Select“ZoneSettings”->“ZoneCong“

->“EditExt.Siren”->“SirenTamper”.Thisoption

needstobeenabled.

Step 5. Testthesirenbyarminganddisarming

withtheControlPanel.Ifthereare5xsirenbeeps

and3xLEDasheswhilearming,thetamper

spring(s)arenotdepressedproperly.Youmayneed

todisablethesirentamper(Step1)andphysically

adjustthesirenmountingposition.Otherwisethe

installationisnowcompleted.

Operation

Siren Reset

Step 1:SlidethePowerSwitchtoOFFposition.

Step 2:SlideDipSwitch#1toON(rIGHT)

positionthenturnthepowerswitchon.

Step 3:TheLEDswillashfor1cycle.

Step 4:SlidedipSW1backtoOFF(left)

positiontoreturntonormalmode.

Previousalarmwarning

Iftherehasbeenanalarmwhileyouwereaway,

thesirenwillsoundandashfor3seconds

whenthesystemisdisarmed.Pleasebeaware

thattheintrudercouldstillbeinthepremises.

Audio & Visual Status Indication

Siren Audio Strobe light

Arm/Home 1 beep * 3 LED ﬂashes at once

Disarm 2 beeps * Flashes for 1 cycle

Arm (Low Battery) 5 beeps 3 LED ﬂashes for three

times

Disarm (Low Battery) 5 beeps

Sequentially ﬂashes for 2 cycles

Arm (Tamper) 5 beeps 3 LED ﬂashes for three

times

Disarm (Tamper) 2 beeps * Flashes for 2 cycles

* The Siren Audio indication will be affected by the Conﬁrm

Sound. Setting Conﬁrmation to OFF will disable the

conﬁrmation sound.

Siren Audible Performance

Thesirenproducesaminimumof105dBA

soundpressureat1metre.Thesirenduration

dependsontheparameterintheControlPanel.

Burglar/Emergency/TamperAlarm-thesiren

givesacontinuousalarmsoundwithsequential

ashesuntilthepresetsirenlengthcomestoa

stop(default:3minutes).

Firealarm-thesirengivesacontinuousalarm

sound(2-secondonand1-secondoff)with

sequentialashesuntilthepresetsirenlength

(default:3minutes).

Atlowbatterycondition,beepingoccurs

irregularly.

Thesirenissilencedwheneitherthe

programmedsirendurationexpiresorwhenthe

userdisarmthesystem.

Changing Batteries

TheSirenispoweredby4xD-cellAlkaline

batterieswithalifeexpectancyofover3years

duringnormaloperationorbyanoptionalDC

adaptor12V1A.

Inthecentrethereisapowerswitchtoisolate

thebatterycompartment.

Underlowbatteryconditionthesirenwillbeep

5timesduringarminganddisarming.This

indicatesthatthesirenhasenoughpowerto

operateforabout1month.Pleasereplacethe

batteriesimmediately.Thereisnolowbattery

conditionifaDCpoweradaptorisused.

Step 1:Disablethesirentamperasfollows:

Select“ZoneSettings”->“ZoneCong“->

“EditExt.Siren”->“SirenTamper”.

Step 2:Openthesirencover.Slidethepower

switchtoOFFposition.

Step 3. Thebatterycompartmentisalarge

boxinthesirenwithalidsecuredby4screws.

Removetheoldbatteriesandthenpressthe

LearnButtonfor1~2secondstodischarge.

Step 4:Insert4xnewDcellalkalinebatteries

observingthepolarity.Thesirenwillbeepand

ashwhenthelastbatteryisinserted.

Step 5:Replacethebatterycompartmentlid

andthesirencover.

Step 6:Enablethesirentamperasfollows:

Select“ZoneSettings”->“ZoneCong“->

“EditExt.Siren”->“SirenTamper”.

Specication

Environmentalconditions:

-10cto40c,relativehumidity85%non-

condensing.ForOutdoor/Indooruse,

IP44.

Radio

868.35MHzFM

Battery:

4x1.5VDCellAlkalinebattery

Dimension:

257.5mm(diameter)x60.65mm

Standard:

EN300-220-1

EN301489-1,3

EN60950

PD6662:2010Grade2Class3

2 Year Instruction Statement:

Thisproductisguaranteedforconsumers

againstfaultyworkmanship,materialsand

functionforaperiodof2yearsfromthedate

ofpurchaseprovidingthefullinstallationand

maintenanceinstructionsarefollowed.Please

keepyourproofofpurchasesafe,thismust

besubmittedwhenmakingaclaimunderthis

guarantee.

Pleasenotethatitisaconditionofthis

guaranteethatyourYaleproduct:

•Hasbeencorrectlyinstalledandmaintained

inaccordancewiththeYaleinstallationand

maintenanceinstructionsprovidedtoyouat

thetimeofpurchase.

•Hasnotbeenmodiedordamagedinanyway.

•Hasnotbeensubjectedtounauthorized

repairs.

Yaleareresponsibleunderthisguaranteefor

repairingtheproductorreplacingtheproduct

aswedeemnecessary.Ifthereisfaultwiththe

product,pleasecontactCustomerServiceson

01902364647,whowillgiveyouthenameofan

expertandconrmwhatyouneedtodotomake

aclaimunderthisguarantee.

Pleasedonotcarryoutanyrepairswithoutour

authorityorbyusinganunauthorisedexpert.

Anyrepairsorotherworkscarriedoutwithout

ourauthorizationorbyusinganunauthorized

expertwillnotbecoveredunderthisguarantee.

Thisguaranteeisnontransferrableandapplies

toproductspurchasedintheUnitedKingdom

only.Thisguaranteedoesnotapplytonormal

wearandtear.Thisdoesnotaffectyourstatutory

rights.Afullcopyoftheproductinstructionsare

availableuponrequestorbyvisitingourwebsite

www.yale.co.uk.

E2 09/11

RoHS

WEEE

Note:Wasteelectricalproductsand

batteriesshouldnotbedisposedofwith

householdwaste.Pleaserecyclewhere

facilitiesexist.Checkwithyourlocal

authorityorretailerforrecyclingadviceor

logontowww.yale.co.ukfordetails.

The world’s favourite lock

School Street, Willenhall, West Midlands WV13 3PW

Assa Abloy ENA-BX, Yale SmartHome Alarm Series User manual

Related papers

Other documents