EnviroLite 8ST134DMDP40 Installation guide

Brand: EnviroLite

Model: 8ST134DMDP40

Type: Installation guide

EnviroLite 8ST134DMDP40 is an 8-ft Strip Light with 0-10V Dimming capabilities and can be used in Multivolt applications. It is suitable for damp locations, has a long lifespan, and is protected against overheating. With its high power factor (>0.9) and thermally protected conductors, this product ensures efficient and safe operation. The dimming range of 3% - 96% allows for precise light adjustment to suit various needs and ambiance preferences.

INSTRUCTIONS MANUAL

8-ft Strip Light, 0-10V Dimming, Multivolt

This product has been manufactured with the highest standards of safety and

quality.

CHARACTERISTICS:

Electrical System Input Power: 117 W

Input Voltage: 120-277 VAC

Input Frequency: 50/60 Hz

Power Factor: > 0.9

Dimmable: 0 - 10 V

Temperature Operating Temperature: -20°C to 45°C

CAUTION:

1. Before starting installation of this fixture or removal of a previous fixture, disconnect the

power by turning off the circuit breaker or by removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL

QUESTIONS. If you have any non-electrical questions about this fixture, please call our

Customer Service Team at phone# on carton label.

3. KEEP your receipt and these Instructions for Proof of Purchase.

DIMMING:

Brand

Series

Model #

Wiring

Load

Capacity (A)

Dimming

Range

Max # of

Luminaires

@ 120V

Max # of

Luminaires

@ 277V

Leviton

Illumatech

IP710-LFZ

3-Way

3% - 96%

Lutron

Diva

DVSTV

3-Way

3% - 100%

Maestro

MS-Z101

3-Way

4% - 100%

Nova T

NTSTV

single

3% - 100%

Philips

Sunrise

Preset

SR500ZTUNV

3-Way

3% -94%

Luxdrive

A019

3% - 100%

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

GENERAL:

1. All electrical connections must be in accordance with local, and national electrical

codes.

2. Prior to installation it is important to follow the following guidelines:

A. Turn off the main power at the circuit breaker before installing the fixture, to

prevent possible shock.

B. Be sure that no wires were damaged during installation and that there are no

rough or sharp edges in contact with the wires.

WARNING:

• Min 90°C supply conductors, THERMALLY PROTECTED.

• This product must be installed in accordance with the applicable installation

code by a person familiar with the construction and operation of the product and

the hazards involved.

• Blinking light of this thermally protected luminaire may indicate overheating.

• Suitable for damp locations.

1 Luminaire

INSTALLATION & ASSEMBLY:

NOTE: The mounting hardware is not included.

1. Turn off the power at the circuit breaker box.

2. Remove the fixture from the packaging.

3. Pull the light assembly away from the fixture pan.

[Fig. 1]

4. Remove a knockout near the center of the fixture pan.

If the fixture will be connected to a dimmer, remove an

additional knockout from the side of the fixture pan.

[Fig. 2]

5. Align the fixture pan over the outlet box. Mark the

location of the fixture pan holes onto the ceiling. Drill a

hole at each marking on the ceiling. Carefully hammer a

ceiling anchor into each drilled hole. [Fig. 3]

6. Thread the power supply wires through the knockout

hole. If the fixture will be connected to a dimmer, pull

out the dimming wires from any other knockout hole.

See page 2 for dimming connections. [Fig. 3] If the

fixture will not be connected to a dimmer, cap off each

of the dimming wires with a wire nut. [Fig. 4]

7. Align the fixture pan with the ceiling anchors and

screw an anchor screw into each ceiling anchor.

Make sure the anchor screws are tightened. [Fig. 3]

8. Insert the black supply wire and white supply wire

into the corresponding openings of the quick

connector. Connect the fixture ground wire and the

supply ground wire together using a wire nut. Wrap

the wire connection with electrical tape for a more

secure connection. Carefully tuck all the wires and wire

connections into the outlet box. [Fig. 3]

9. Snap the light assembly back onto the fixture pan.

[Fig. 5]

10. Restore power at the circuit breaker box.

Fig. 4

PURPLE FIXTURE WIRE

GREY FIXTURE WIRE

NO DIMMING

Fig. 5

Fig. 2

Fig. 1

Fig. 3

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use

clean water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of

the fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry

soft cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of five (5) years from date of purchase. This warranty applies only to the

original consumer purchaser and only to products used in normal use and service. If this product is

found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair

or replacement of the product at the manufacturer’s discretion, provided that the product has not

been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling.

This warranty shall not apply to any product that is found to have been improperly installed, set-up,

or used in any way not in accordance with the instructions supplied with the product. This warranty

shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence,

alteration, or faulty installation, or any other failure not relating to faulty material or workmanship.

This warranty shall not apply to the finish on any portion of the product, such as surface and/or

weathering, as this is considered normal wear and tear. The manufacturer does not warrant and

specially disclaims any warranty, whether expressed or implied, of fitness for a particular

purpose, other than the warranty contained herein. The manufacturer specifically disclaims

any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor/expense costs involved in the replacement or repair

of said product.

Problem

Possible Cause

Solution

Light will not turn on.

1. Power is off.

1. Make sure power supply is

on.

2. Faulty switch.

2. Test or replace switch.

3. Faulty wire connection.

3. Check wiring.

Fixture is dim.

The gray and purple dimming

wires are touching each other.

Separate the grey and purple

wires.

Fuse blows or circuit breaker

trips when light is turned on.

Crossed wires or power wire is

grounding out.

Check wire connections.

Page is loading ...

EnviroLite 8ST134DMDP40 Installation guide

Brand: EnviroLite

Model: 8ST134DMDP40

Type: Installation guide

Download PDF

report

in other languages

français: EnviroLite 8ST134DMDP40 Guide d'installation
español: EnviroLite 8ST134DMDP40 Guía de instalación

EnviroLite 8ST134DMDP40 Installation guide

EnviroLite 8ST134DMDP40 Installation guide

in other languages

Related papers

Other documents