Setting the week plan
In a ring around the clock you’ll nd
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
then position the sliders accordingly:
For Comfort temperature, the sliders
point toward the centre; for Reduced
temperature, they point out.
Note:
Minimum duration of a period is 2
hours.
ECL Comfort 100M quick guide
Remove tape on the back.
Position on inside of the
ECL Comfort cover.
*087R9729*
*vi7ac302*
ECL Comfort 100M
VI.7A.C3.02
2004.05
Clock and week planClock and week plan
ECL Comfort 100M quick guide
Remove tape on the back.
Position on inside of the
ECL Comfort cover.
*087R9729*
*vi7ac302*
ECL Comfort 100M
VI.7A.C3.02
2004.05
Setting the week plan
In a ring around the clock you’ll nd
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
then position the sliders accordingly:
For Comfort temperature, the sliders
point toward the centre; for Reduced
temperature, they point out.
Note:
Minimum duration of a period is 2
hours.
Temperature setting
Heat curve
displacement or
room temperature
(if room sensor
is installed:
Range 12–28 °C,
“0” is 20 °C)
0
+8
-8
Mode selector
Manual operation
Comfort temperature
Automatic (normal)
Reduced temperature
Standby
Temperature setting
Heat curve
displacement or
room temperature
(if room sensor
is installed:
Range 12–28 °C,
“0” is 20 °C)
0
+8
-8
Mode selector
Manual operation
Comfort temperature
Automatic (normal)
Reduced temperature
Standby
Setting the clock
Week day Minute hand
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
White arrow
Sliders
Turn the minute hand until the white
arrow points to the current week day
and hour in the outer ring. Do not turn
the outer ring itself.
Please note!
Do not turn anti-clockwise!
Setting the clock
Week day Minute hand
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
White arrow
Sliders
Turn the minute hand until the white
arrow points to the current week day
and hour in the outer ring. Do not turn
the outer ring itself.
Please note!
Do not turn anti-clockwise!
XXXXXXXXXXX
Mixing controller
Temperature
Heat curve
reduction
slope
You can choose how many degrees
below Comfort temperature you want
the ow temperature/room temperature
to be reduced, during time periods with
Reduced temperature.
Battery holder
Heat curve slope
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1.8
1.2
0.6
0.2
2.2
˚C
˚C
You can set the heat curve slope in a
range from 0.2 to 2.2.
Note:
The slope is factory-set to 1.2.
Battery holder
Heat curve slope
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1.8
1.2
0.6
0.2
2.2
˚C
˚C
You can set the heat curve slope in a
range from 0.2 to 2.2.
Note:
The slope is factory-set to 1.2.
Mixing controller
Temperature
Heat curve
reduction
slope
You can choose how many degrees
below Comfort temperature you want
the ow temperature/room temperature
to be reduced, during time periods with
Reduced temperature.
Change the back-up battery every
two years
To ensure operation during power
failure/interruption, there is a back-up
battery. This battery is normally not
in use, but Danfoss recommends that
you replace it every two years. Use an
Alcaline AAA 1.5 V type.
Installation date:
Date replaced:
1
2
3
4
5
6
7
8
Change the back-up battery every
two years
To ensure operation during power
failure/interruption, there is a back-up
battery. This battery is normally not
in use, but Danfoss recommends that
you replace it every two years. Use an
Alcaline AAA 1.5 V type.
Installation date:
Date replaced:
1
2
3
4
5
6
7
8
Service settingsService settings
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss ECL Comfort 100M User guide
-
-
-
-
-
-
-
-
-