ECL Comfort 100B
VI.7A.F3.02
Remove tape backing.
Position on inside of
ECL Comfort cover.
ECL Comfort 100B
VI.7A.F3.02
ECL Comfort 100B quick guide
Remove tape backing.
Position on inside of
ECL Comfort cover.
Setting week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
then position the sliders accordingly:
For Comfort temperature, the
sliders point toward the centre; for
Reduced temperature, they point
out.
Note: Minimum duration of a period
is 2 hours.
ECL Comfort 100B quick guide
Clock and week plan Clock and week plan
Setting week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
them position the sliders accordingly:
For Comfort temperature, the
sliders point toward the centre; for
Reduced temperature, they point
out.
Note: Minimum duration of a period
is 2 hours.
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
Setting the clock
Week day
Minute hand
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week
day and hour in the outer ring. Do
not turn the outer ring itself.
Please note!
Do not turn anti-clockwise!
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
Setting the clock
Week day
Minute hand
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week
day and hour in the outer ring. Do
not turn the outer ring itself.
Please note!
Do not turn anti-clockwise!
Mode selector
Manual operation
Automatic (normal)
Comfort temperature
Reduced temperature
Standby
0
+8
-8
Temperature setting
Heat curve displacement or
room temperature
(if room sensor
is installed:
Range
12–28 °C,
“0” is 20 °C)
Mode selector
Manual operation
Automatic (normal)
Comfort temperature
Reduced temperature
Standby
0
+8
-8
Temperature setting
Heat curve displacement or
room temperature
(if room sensor
is installed:
Range
12–28 °C,
“0” is 20 °C)
Service settingsService settings
Date replaced:
Change the back-up battery every
two years
To ensure operation during power
failure/interruption, there is a back-up
battery. This battery is normally not in
use, but Danfoss recommends that
you replace it every two years. Use an
Alcaline AAA 1.5 V type.
Installation date:
15
26
37
48
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1,8
1,2
0,6
0,2
2,2
C
C
Heating curve slope
You can set the heating curve slope in a
range from 0.2 to 2.2.
Note: The slope is factory-set to 1.8.
Date replaced:
Change the back-up battery every
two years
To ensure operation during power
failure/interruption, there is a back-up
battery. This battery is normally not in
use, but Danfoss recommends that
you replace it every two years. Use an
Alcaline AAA 1.5 V type.
Installation date:
15
26
37
48
Battery holder
Battery holder
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1,8
1,2
0,6
0,2
2,2
C
C
Heating curve slope
You can set the heating curve slope in a
range from 0.2 to 2.2.
Note: The slope is factory-set to 1.8.
Boiler temperature difference
You can set the boiler temperature
difference. Choose a fixed difference
between 1 and 20 K or choose AUTO.
(The difference depends on the load and
thermal conditions.)
Setting the controller
Boiler temp.
difference
Heating
curve slope
Boiler temperature difference
You can set the boiler temperature
difference. Choose a fixed difference
between 1 and 20 K or choose AUTO.
(The difference depends on the load and
thermal conditions.)
Setting the controller
Boiler temp.
difference
Heating
curve slope
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Danfoss ECL Comfort 100B Operating instructions
-
-
-
-
-
-
-
-
-