Page is loading ...
ECL Comfort 100M
VI.7A.C2.02
Remove tape on the back.
Position on inside of
ECL Comfort cover.
ECL Comfort 100M
VI.7A.C2.02
ECL Comfort 100M guick guide
Remove tape on the back.
Position on inside of
ECL Comfort cover.
0
+8
-8
Temperature setting
Heat curve displacement or
room temperature
(if room sensor
is installed:
Range
12 - 28°C,
“0” is 20°C)
Mode selector
Manual operation
Comfort temperature
Automatic (normal)
Reduced temperature
Standby
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
Setting the clock
Week day
Minute hand
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week
day and hour in the outer ring.
Please note!
Do not turn anti-clockwise!
Setting week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
then position the sliders
accordingly:
For Comfort temperature, the
sliders point toward the centre;
for Reduced temperature, they point
out.
Note: Minimum duration of a period
is 2 hours.
ECL Comfort 100M guick guide
Clock and week plan
Clock and week plan
0
+8
-8
Temperature setting
Heat curve displacement or
room temperature
(if room sensor
is installed:
Range
12 - 28°C,
“0” is 20°C)
Mode selector
Manual operation
Comfort temperature
Automatic (normal)
Reduced temperature
Standby
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
1
8
1
2
6
12
3
6
9
Setting the clock
Week day
Minute hand
White arrow Sliders
Turn the minute hand until the white
arrow points to the current week
day and hour in the outer ring.
Please note!
Do not turn anti-clockwise!
Setting week plan
In a ring around the clock you’ll find
the seven days of the week, divided
into one-hour segments.
Decide when you want Comfort or
Reduced temperature for each day,
then position the sliders
accordingly:
For Comfort temperature, the
sliders point toward the centre;
for Reduced temperature, they point
out.
Note: Minimum duration of a period
is 2 hours.
Service settingsService settings
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1,8
1,2
0,6
0,2
2,2
C
C
Heating curve slope
You can set the heating curve slope in a
range from 0.2 to 2.2.
Note: The slope is factory-set to 1.2.
Battery holder
Date replaced:
Change the back-up battery
every two years
To ensure operation during power
failure/interruption, there is a back-
up battery. This battery is normally
not in use, but Danfoss
recommends that you replace it
every two years. Use an Alcaline
AAA 1.5 V type.
Installation date:
15
26
37
48
Mixing controller
Heating curve
slope
Temperature reduction
You can choose how many degrees
below Comfort temperature you want
the flow temperature/room temperature
to be reduced, during time periods with
Reduced temperature.
-20 -10 0 10 20-30
10
20
30
40
50
60
70
80
90
1,8
1,2
0,6
0,2
2,2
C
C
Heating curve slope
You can set the heating curve slope in a
range from 0.2 to 2.2.
Note: The slope is factory-set to 1.2.
Battery holder
Date replaced:
Change the back-up battery
every two years
To ensure operation during power
failure/interruption, there is a back-
up battery. This battery is normally
not in use, but Danfoss
recommends that you replace it
every two years. Use an Alcaline
AAA 1.5 V type.
Installation date:
15
26
37
48
Mixing controller
Heating curve
slope
Temperature reduction
You can choose how many degrees
below Comfort temperature you want
the flow temperature/room temperature
to be reduced, during time periods with
Reduced temperature.
/