Cornelius 230 VAC Installation guide

230 VAC
Brand
Cornelius
Model
230 VAC
Category
Water dispensers
Type
Installation guide

This manual is also suitable for

Cornelius 230 VAC is a versatile power solution designed for V-Series 2 Flavor units. It provides a reliable power supply with a voltage range of 208-230V, 60Hz, and a current rating of 30 Amp. This power cord kit ensures efficient operation of your V-Series 2 Flavor unit, enabling you to dispense delicious beverages effortlessly.

Cornelius 230 VAC is a versatile power solution designed for V-Series 2 Flavor units. It provides a reliable power supply with a voltage range of 208-230V, 60Hz, and a current rating of 30 Amp. This power cord kit ensures efficient operation of your V-Series 2 Flavor unit, enabling you to dispense delicious beverages effortlessly.

FCB Cord Kit for V-Series 2 Flavor Installation Instructions
© 2003-2014, Cornelius Inc. - 1 - Publication Number: 629088372INS
INSTALLATION INSTRUCTIONS
FCB CORD KIT FOR V-SERIES 2 FLAVOR
The following instructions should be used for installation of a power cord for a V-Series 2 Flavor unit.
Each kit will supply power to 1 unit.
Parts List
Tools Required
Phillips Screwdriver
Flat Screwdriver
Pliers
CAUTION – Only trained and certified electrical technicians should service this unit. ALL WIRING
MUST CONFORM TO NATIONAL AND LOCAL CODES.
DANGER – To avoid possible serious injury or death the ELCB (earth leakage circuit breaker) must
be installed in the electrical circuit of all units.
WARNING – To avoid possible electrical shock make sure the unit is properly grounded by con-
necting the earth ground cable, in the power cord to any connection in the machine marked with a
ground symbol.
CAUTION – The wiring must be properly grounded and connected through a disconnect switch
(slow-blow fuse or equivalent HVAC/R circuit breaker).
Electrical Requirements
Refer to the nameplate to determine the power requirements before connecting electrical power to the
unit. Voltage across contactor terminals L1 and L2, with the compressor running, must be within voltage
limits described in Table 1.
If the line voltage does not meet these requirements see the possible corrective actions in Table 2.
Item
Number
Description Qty
1 30 Amp Power Cord 1
2 Strain Relief 2
Table 1
Unit Requirements
V-Series 2 Flavor Integral Condense 208-230V, 60Hz, 30 Amp
V-Series 2 Flavor Water Condense 208-230V, 60Hz, 30 Amp
Table 2
Voltage Corrective Action
Below 180 VAC Do Not Connect Unit
180-190 VAC Boost voltage by +32 V
191-207 VAC Boost voltage by +16 V
208-230 VAC Use line voltage
231-246 VAC Reduce voltage by –16 V
247-262 VAC Reduce voltage by –32 V
Above 262 VAC Do Not Connect Unit
Revision Date: March 24, 2014 www.cornelius.com Revision: B
FCB Cord Kit for V-Series 2 Flavor Installation Instructions
Publication Number: 629088372INS - 2 - © 2003-2014, Cornelius Inc.
Installation Steps
1. Switch the power to the unit off or remove the fuse to the electrical power circuit breaker.
2. Remove the back panel and the right side panel to gain access to the electrical area in the back of
the unit.
3. For counter top units, remove the junction box cover to gain access to the power leads. For floor
model units, remove the cover to the contactor box.
4. On both strain relief parts, loosen the screws until no threads show through the bottom.
5. Install the first strain relief to the bottom of the unit.
6. Install the second strain relief to the side of the either the junction box or the contactor box.
7. Feed the power cord through the first strain relief,
lead end first, from the outside of the unit to the
inside of the unit.
8. Pull the power cord to the second strain relief.
FCB Cord Kit for V-Series 2 Flavor Installation Instructions
© 2003-2014, Cornelius Inc. - 3 - Publication Number: 629088372INS
9. Feed the power cord through the second strain relief from the side into the junction box/contactor
box.
10. For counter top units, attach the black and white leads from the power cord to the brown and blue
power leads from the unit. For floor model units attach the black and white leads from the power
cord to the right side of the compressor contactor.
11. Remove the top ground nut from the ground stud. Slip the ring of the green ground lead over the
ground stud and secure it by tightening the ground nut.
FCB Cord Kit for V-Series 2 Flavor Installation Instructions
Publication Number: 629088372INS - 4 - © 2003-2014, Cornelius Inc.
12. Pull the slack out of the power cord through the side of the junction box/contactor box and tighten
the strain relief on the side of the junction box/contactor box.
13. Pull the slack out of the power cord through the
back of the unit and tighten the strain relief on the
outside of the unit.
14. Replace the cover to the junction box/contactor box.
15. Replace the back panel and left side panel.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Cornelius 230 VAC Installation guide

230 VAC
Brand
Cornelius
Model
230 VAC
Category
Water dispensers
Type
Installation guide
This manual is also suitable for

Cornelius 230 VAC is a versatile power solution designed for V-Series 2 Flavor units. It provides a reliable power supply with a voltage range of 208-230V, 60Hz, and a current rating of 30 Amp. This power cord kit ensures efficient operation of your V-Series 2 Flavor unit, enabling you to dispense delicious beverages effortlessly.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents