1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
h
ousing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure
bare wires cannot be seen outside the terminal block. Tighten
down on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable
into track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty,
listing and create a potential safety hazard.
• Risk of shock. 24V system not suitable for outdoor use.
I
MPORTANT SAFETY INSTRUCTIONS
INSTALLATION
HC-203
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the
installation instructions do apply to this fixture. Fill in Item Number on Carton
and File This Sheet For Future Reference. ITEM#_______________
011100
HC-203
1. Secure conduit connector (not supplied) to housing.
2. Strip 1/4" from end of power source wires and feed wire into
h
ousing through conduit connector. Secure wire in conduit
connector by tightening screw(s).
3. Secure housing to surface with screw.
4. Place striped ends of wire into terminal block making sure
bare wires cannot be seen outside the terminal block. Tighten
down on terminal block screws to secure in place.
5. For 9031 hardwire kit, feed fixture wires through sleeving, to
provide extended wire protection between track and cover, for
4006 or 4008 fixtures.
6. Secure track to surface with double face tape (if applicable)
making sure end of track is in notch of housing. Place cable
into track (if applicable). Snap cover onto track (if applicable).
7. Strip 1/4" from end of cable and place cable end into terminal
block making sure no bare wires can be seen outside the
terminal block. Tighten down on terminal block screws.
8. Snap cover onto housing.
• Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty,
listing and create a potential safety hazard.
• Risk of shock. 24V system not suitable for outdoor use.
I
MPORTANT SAFETY INSTRUCTIONS
INSTALLATION
HC-203
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the
installation instructions do apply to this fixture. Fill in Item Number on Carton
and File This Sheet For Future Reference. ITEM#_______________
SLEEVING
COVER
COVER
TRACK
SCREW
NOTCH
HOUSING
TERMINAL BLOCK
*NOT SUPPLIED
FIGURE 1
*CONDUIT
CONNECTOR
HC-203
SLEEVING
COVER
COVER
TRACK
SCREW
NOTCH
HOUSING
TERMINAL BLOCK
*NO
T SUPPLIED
FIGURE 1
*CONDUIT
CONNECTOR
-
1
Generation Lighting 9481-15 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Satco TP170 Operating instructions
-
Grizzly G0492 User manual
-
Friedrich Heat Pump HEAT PUMPS User manual
-
Miller Welding User manual
-
Friedrich WallMaster PTAC User manual
-
-
-
-
Legrand adorne APTR15TM4 Specification
-
Wayne-Dalton Stud Sensor 3651-372 User manual
