Altronix T2MK3F4D Installation guide
- Category
- Security device components
- Type
- Installation guide
Altronix T2MK3F4D is a fully assembled kit that integrates power supply, access control, and power distribution components into a single enclosure. It includes an eFlow6NB power supply/charger, an ACM4CB access power controller, a VR6 voltage regulator, and a PDS8CB dual input power distribution module. This kit is designed to provide reliable power and control for access control systems, door strikes, and other low-voltage devices. With its compact size and easy installation process, the T2MK3F4D is an ideal solution for small to medium-sized access control applications.
Altronix T2MK3F4D is a fully assembled kit that integrates power supply, access control, and power distribution components into a single enclosure. It includes an eFlow6NB power supply/charger, an ACM4CB access power controller, a VR6 voltage regulator, and a PDS8CB dual input power distribution module. This kit is designed to provide reliable power and control for access control systems, door strikes, and other low-voltage devices. With its compact size and easy installation process, the T2MK3F4D is an ideal solution for small to medium-sized access control applications.
Access & Power Integration Solutions
Installation Guide for models:
Rev. TMKD060117 More than just power.™
Installing Company: __________________________ Service Rep. Name: ______________________________________________
Address: _______________________________________________________________ Phone #: ___________________________
T2MK3F4D
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM4CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK3F4DQ
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM4CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK3F8D
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK3F8DQ
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow6NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK7F8D
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow104NB - Power Supply/Charger
- (1) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK7F8DQ
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane
- (1) eFlow104NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (1) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK75F16D
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane and TMV2 door backplane
- (1) eFlow104NB and (1) eFlow102NB - Power Supply/Chargers
- (2) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PD8ULCB - Power Distribution Module
T2MK75F16DQ
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane and TMV2 door backplane
- (1) eFlow104NB and (1) eFlow102NB - Power Supply/Chargers
- (1) LINQ2 - Network Communications Module
- (2) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PD8ULCB - Power Distribution Module
T2MK77F16D
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane and TMV2 door backplane
- (2) eFlow104NB - Power Supply/Charger
- (2) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
T2MK77F16DQ
Fully assembled kit includes:
- Trove2 enclosure with TM2 backplane and TMV2 door backplane
- (2) eFlow104NB - Power Supply/Charger
- (1) LINQ2 - Network Communications Module
- (2) ACM8CB - PTC Access Power Controller
- (1) VR6 - Voltage Regulator
- (1) PDS8CB - Dual Input Power Distribution Module
- 2 - T2MKD Kits
Overview:
Altronix Trove Mercury kits are pre-assembled and consist of Trove2M2 enclosure with factory installed Altronix power supply/
charger(s) and sub-assemblies. These kits also accommodate various combinations of Mercury boards for up to sixteen (16) doors in
a single enclosure.
Configuration Chart:
Altronix
Model Number
Nominal DC Output
Voltage
Maximum
Supply
Current for
Main and Aux.
Outputs on Power
Supply board
and ACM4CB/
ACM8CB
Access Power
Controller’s
outputs
Fail-Safe/Fail-Secure Auto-
Resettable Outputs
120VAC 60Hz
Input Current (A)
Current Per
ACM4CB/ACM8CB Output (A)
Power Supply Board
Input Fuse Rating
Power Supply Board
Battery Fuse Rating
ACM4CB/ACM8CB
Board Input Fuse Rating
ACM4CB/ACM8CB Board
Output PTC Rating
PDS8CB Board
Input Fuse Rating
PDS8CB Board
Output PTC Rating
PD8ULCB Board
Output PTC Rating
Power
Supply 1
Power
Supply 2
[DC] [Aux] [DC] [Aux]
Output Range
(VDC)
Output Range
(VDC)
Output Range
(VDC)
Output Range
(VDC)
T2MK3F4D
20.19-
26.4
20.19-
26.4
---- ---- 24VDC @ 5.8A 4 3.5 2.0
5A/
250V
10A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK3F4DQ
20.19-
26.4
20.19-
26.4
---- ---- 24VDC @ 5.8A 4 3.5 2.0
5A/
250V
10A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK3F8D
20.19-
26.4
20.19-
26.4
---- ---- 24VDC @ 5.8A 8 3.5 2.0
5A/
250V
10A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK3F8DQ
20.19-
26.4
20.19-
26.4
---- ---- 24VDC @ 5.8A 8 3.5 2.0
5A/
250V
10A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK7F8D
20.17-
26.4
20.28-
26.4
---- ---- 24VDC @ 9.2A 8 4.5 2.0
6.3A/
250V
15A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK7F8DQ
20.17-
26.4
20.28-
26.4
---- ---- 24VDC @ 9.2A 8 4.5 2.0
6.3A/
250V
15A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK75F16D
20.17-
26.4
20.28-
26.4
9.7-
13.2
10.03-
13.2
12VDC @ 9.3A
24VDC @ 9.2A
16 8 2.0
6.3A/250V
5A/250V
15A/
32V
10A/
250V
2A ---- ---- 2A
T2MK75F16DQ
20.17-
26.4
20.28-
26.4
9.7-
13.2
10.03-
13.2
12VDC @ 9.3A
24VDC @ 9.2A
16 8 2.0
6.3A/250V
5A/250V
15A/
32V
10A/
250V
2A ---- ---- 2A
T2MK77F16D
20.17-
26.4
20.28-
26.4
20.17-
26.4
20.28-
26.4
24VDC @ 9.2A 16 9 2.0
6.3A/
250V
15A/
32V
10A/
250V
2A
10A/
250V
2A ----
T2MK77F16DQ
20.17-
26.4
20.28-
26.4
20.17-
26.4
20.28-
26.4
24VDC @ 9.2A 16 9 2.0
6.3A/
250V
15A/
32V
10A/
250V
2A
10A/
250V
2A ----
Installation Instructions:
Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities
having jurisdiction. Product is intended for indoor use only.
1. Remove backplane(s) from enclosure. Do not discard hardware.
2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws
in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level and secure.
Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the
enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.
3. Mount included UL Listed tamper switch (Honeywell Model 112 or equivalent) in desired location, opposite hinge. Slide the
tamper switch bracket onto the edge of the enclosure approximately 2” from the right side
(Fig. 1, pg. 2). Connect tamper switch wiring to the Access Control Panel input or the
appropriate UL Listed reporting device. To activate alarm signal open the
door of the enclosure.
4. Refer to the eFlow Power Supply/Charger Installation Guide (eFlow6NB, eFlow102NB,
eFlow104NB) and Sub-Assembly Installation Guide for the following models:
ACM4CB, ACM8CB, LINQ2, PDS8CB, VR6 for further installation instructions.
5. Fasten snap on standoffs onto metal pems configuration of backplane depending on the
Mercury access controller (Fig. 2-5, pg. 3-6).
6. Position Mercury access controller module over corresponding standoffs and depress onto
snap on standoffs (Fig. 2-5, pg. 3-6).
7. Mount backplane to enclosure with hardware.
Edge of
Enclosure
to Access Control Panel
or U.L. Listed
Reporting Device
Enclosure
Honeywell
model # 112
Tamper Switch
or equivalent
(provided)
Fig. 1
T2MKD Kits - 3 -
T2MK3F4D:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) ACM4CB - 4 PTC output Access Power Controller, one (1) VR6
- 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB - 8 PTC output Dual Input Power Distribution Module.
T2MK3F4DQ:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM4CB -
4 PTC output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB -
8 PTC output Dual Input Power Distribution Module.
T2MK3F8D:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) ACM8CB - 8 PTC output Access Power Controller, one (1) VR6
- 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB - 8 PTC output Dual Input Power Distribution Module.
T2MK3F8DQ:
One (1) eFlow6NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM8CB -
8 PTC output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB -
8 PTC output Dual Input Power Distribution Module.
Fig. 2
LINQ2
(T2MK3F4DQ, T2MK3F8DQ)
Altronix
eFlow6NB
or ACM8CB
(T2MK3F8)
Altronix
ACM4CB
(T2MK3F4)
Altronix
PDS8CB & VR6
- 4 - T2MKD Kits
T2MK7F8D:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger, one (1) ACM8CB - 8 PTC output Access Power Controller, one (1) VR6
- 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB - 8 PTC output Dual Input Power Distribution Module.
T2MK7F8DQ:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger, one (1) LINQ2 Network Communication Module, one (1) ACM8CB -
8 PTC output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator, and one (1) PDS8CB -
8 PTC output Dual Input Power Distribution Module.
Fig. 3
LINQ2
(T2MK7F8DQ)
Altronix
eFlow104NB
Altronix ACM8CB
Altronix
PDS8CB & VR6
T2MKD Kits - 5 -
T2MK75F16D:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger and one (1) eFlow102NB - 12VDC @ 10A Power Supply/Charger,
two (2) ACM8CB - 8 PTC output Access Power Controller, and one (1) PD8ULCB - 8 PTC output Power Distribution Module.
T2MK75F16DQ:
One (1) eFlow104NB - 24VDC @ 10A Power Supply/Charger and one (1) eFlow102NB - 12VDC @ 10A Power Supply/Charger,
one (1) LINQ2 Network Communication Module, two (2) ACM8CB - 8 PTC output Access Power Controller,
and one (1) PD8ULCB - 8 PTC output Power Distribution Module.
Fig. 4
LINQ2
(T2MK75F16DQ)
Altronix
eFlow102NB
Altronix ACM8CB
Altronix
eFlow104NB
Altronix ACM8CB
Altronix
PD8ULCB
- 6 - T2MKD Kits
T2MK77F16D:
Two (2) eFlow104NB - 24VDC @ 6A Power Supply/Charger, two (2) ACM8CB - 8 PTC output Access Power Controller, one (1)
VR6 - 24VDC input to 12VDC output Voltage Regulator and one (1) PDS8CB - 8 PTC output Dual Input Power Distribution Module.
T2MK77F16DQ:
Two (2) eFlow104NB - 24VDC @ 6A Power Supply/Charger, one (1) LINQ2 Network Communication Module , two (2) ACM8CB - 8
PTC output Access Power Controller, one (1) VR6 - 24VDC input to 12VDC output Voltage Regulator and one (1) PDS8CB - 8 PTC
output Dual Input Power Distribution Module.
Fig. 5
LINQ2
(T2MK77F16DQ)
Altronix
eFlow104NB
Altronix ACM8CB
Altronix
eFlow104NB
Altronix ACM8CB
Altronix
PDS8CB & VR6
T2MKD Kits - 7 -
A
A
A
A
A
A
B
B
B
B
B
B
C
C
C
TMV2 (T2MK75F16D, T2MK75F16DQ, T2MK77F16D, and T2MK77F16DQ):
TMV2 accommodates a variety of Mercury boards with or without Altronix sub-assemblies for access systems.
Configuration of Mercury and/or Altronix Boards
Mercury Access Controllers:
1. Fasten snap on standoffs onto metal pems configuration (A) (B) of backplane depending on the access controller (Fig. 6, pg. 7).
2. Position access controller module over corresponding standoffs and depress onto snap on standoffs (Fig. 6a, pg. 7).
3. Mount backplane to enclosure with hardware.
Altronix Sub-Assemblies and/or Adapters:
1. Fasten nylon / snap on standoffs to pems which match the hole pattern for Altronix Sub-Assemblies (Fig. 6, 6a, pg. 7).
2. Mount boards to standoffs utilizing pan head screws provided with the product or by depressing board onto snap on standoff
(Fig. 6, pg. 7).
Note: For GB1 please use standoffs supplied with the adapter.
Access Controller Position Chart for the Following Models:
Mercury
Access Controller Pem Mounting
EP1502, MR52, MR16IN, MR16OUT A
EP2500, MUX8 B
Altronix
Sub-Assembly or Adapter Pem Mounting
ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6, GB1 (Genetec Synergis Cloud Link adapter plate) C
Fig. 6
Snap on
Standoff
N
ylon
Standoff
Sub-Assembl
y
Backplane
Pem
Fig. 6a
- 8 - T2MKD Kits
Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: [email protected] | Lifetime Warranty | Made in U.S.A.
IITrove2M2 Kit Series B12R
MEMBER
Enclosure Dimensions (H x W x D approximate):
27.25” x 21.5” x 6.5” (692.15mm x 552.5mm x 165.1mm)
G
1.25”
(31.75mm)
1.25”
(31.75mm)
6.25”
(158.75mm)
6.25”
(158.75mm)
6.75”
(171.45mm)
8.25”
(209.54mm)
8.00”
(203.2mm)
1.5”
(38.1mm)
1.25”
(31.75mm)
0.85”
(21.59mm)
0.85”
(21.59mm)
1.00”
(25.4mm)
2.00”
(50.8mm)
1.25”
(31.75mm)
2.00”
(
50.8mm
)
2.00”
(
50.8mm
)
5.25”
(
133.35mm
)
5.25”
(
133.35mm
)
7.00”
(
177.79mm
)
2.00”
(50.8mm)
2.00”
(50.8mm)
27.00”
(685.8mm)
3.50”
(88.9mm)
0.5625”
(14.29mm)
2.415”
(61.34mm)
0.685”
(17.399mm)
1.77”
(44.96mm)
3.50”
(88.9mm)
21.50”
(546.1mm)
19.80”
(502.92mm)
5.25”
(133.35mm)
5.25”
(133.35mm)
0.885” (22.479mm)
1.125” (28.32mm)
Knockouts
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Altronix T2MK3F4D Installation guide
- Category
- Security device components
- Type
- Installation guide
Altronix T2MK3F4D is a fully assembled kit that integrates power supply, access control, and power distribution components into a single enclosure. It includes an eFlow6NB power supply/charger, an ACM4CB access power controller, a VR6 voltage regulator, and a PDS8CB dual input power distribution module. This kit is designed to provide reliable power and control for access control systems, door strikes, and other low-voltage devices. With its compact size and easy installation process, the T2MK3F4D is an ideal solution for small to medium-sized access control applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Altronix Trove T2MK3F4D Installation guide
-
Altronix T2MK3F4D User manual
-
-
-
-
Altronix T2MK3F4 Installation guide
-
-
-
Altronix LINQ2 Installation guide
-
Altronix PD8UL Datasheet
Other documents
-
Hagerco 2908 - 1A Modular Access Control Power Supply Installation guide
-
TROVE T2MK74 Installation guide
-
TROVE T2KHK3F12 User manual
-
TROVE T1RM3CK1 Installation guide
-
AUTOTECH 10.411.01.219K Installation guide
-
GENETEC SYNERGIS IX SY-SIX-PSU-DIN-4A 12V 4A Offline Intelligent Battery Backup PSU - DIN Rail Installation guide
-
TROVE Trove2KH2 Access and Power Integration Installation guide
-
GENETEC SYNERGIS IX SY-SIX-CTRL-DIN-1D IP single door controller (2 readers) - DIN rail Installation guide
-
GENETEC SYNERGIS IX SY-SIX-PSU-DIN-8A 12V 8A Intelligent Battery Backup Power Supply Unit User manual
-
GENETEC SYNERGIS IX SY-SIX-CTRL-DIN IP door controller (4 readers) - DIN rail Installation guide
