2. Lumination
  3. LBR-LBT Series LED Diff

Lumination LBR-LBT Series LED Diff Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Lumination LBR-LBT Series LED Diff Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 1 of 3
(Rev 06/28/23)
IND403-Lumination-LBR-LBT-Series-LED-Difuser-Replacement-Installation-Guide_R01
Installation Guide
IND403
Lumination® LED Luminaire
Diuser Replacement
(LBT/LBR Series)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes
• Use only UL approved wire for input/output connections.
Only use size 18 AWG (0.75mm
2
).
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation
électrique.
RISK OF FIRE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de
connexion. Utilisez taille 18 AWG (0.75mm
2
).
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Specications
Description Code Corresponding Luminaires
LBT22 (dimmable) diuser LBT22 Series
LBT14 (dimmable) diuser LBT14 Series
LBT24 (dimmable) diuser LBT24 Series
LBR22 (dimmable) diuser LBT22 Series
LBR14 (dimmable) diuser LBT14 Series
LBR24 (dimmable) diuser LBT24 Series
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 2 of 3
(Rev 06/28/23)
IND403-Lumination-LBR-LBT-Series-LED-Difuser-Replacement-Installation-Guide_R01
Lumination® (LBT/LBR - Series) Installation Guide
TURN OFF POWER at the source
to the luminaire.
1
Disconnect the AC and dimming
wires. Remove the xture from
the ceiling xture.
 2
Remove the end cap that is opposite
to the driver/electrical box.
 3
LBT Diuser Replacement Steps
NOTE: The following steps depict the 22 Series luminaire. However, the procedure is the same for the 14 and 24 Series xtures.
Slide out the old diuser.
4
Slide in the new diuser. Make sure
the round corner on the diuser
slides in rst as shown in the circled
area of the above picture.
5
Replace the end cap
6
Install the xture back to the ceiling.
Connect the AC and dimming wires.
7
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 3 of 3
(Rev 06/28/23)
IND403-Lumination-LBR-LBT-Series-LED-Difuser-Replacement-Installation-Guide_R01
Lumination® (LBT/LBR - Series) Installation Guide
Rotate latches to unlock the front
bezel.
1
Swing down panel and lift o front
bezel.
2
LBR Diuser Replacement Steps
NOTE: The following steps depict the 22 Series luminaire. However, the procedure is the same for the 14 and 24 Series xtures.
NOTE: Rough side of diuser should
face UP in this orientation.
Reattach end rail with screws.
5
Place front bezel with diuser on
table. Unfasten the two rail screws
on the end rail with latches, then
remove this end rail.
Locate round corner here
Remove the old diuser by sliding
it toward the side without end rail.
Insert new diuser, keeping the
round corner of diuser on bottom
left.
3
4 6
Hang panel on its hinges and swing
up into place. Rotate latches on front
bezel to fasten it.
/