Toro Z320 Z Master, With 122cm Mower and Bagger User manual

Operator’s Manual

IMPORTANT: Read this manual carefully. It contains information about your

safety and the safety of others. Also become familiar with the controls and

their proper use before you operate the product.

FORM NO. 3319–942GB

Z–320

OUT FRONT Z

Model No. 74191 – 890001 & Up

The Toro Company – 1997

Introduction

Thank you for purchasing a Toro product.

All of us at Toro want you to be completely satisfied

with your new product, so feel free to contact your

local Authorized Service Dealer for help with service,

genuine replacement parts, or other information you

may require.

Whenever you contact your Authorized Service

Dealer or the factory, always know the model and

serial numbers of your product. These numbers will

help the Service Dealer or Service Representative

provide exact information about your specific

product. You will find the model and serial number

plate located in a unique place on the product as

shown below

.

1



1. Model

and Serial Number Plate

For your convenience, write the product model and

serial numbers in the space below.

Model No:

Serial No.

Read this manual carefully to learn how to operate

and maintain your product correctly. Reading this

manual will help you and others avoid personal injury

and damage to the product. Although we design,

produce and market safe, state-of-the-art products,

you are responsible for using the product properly

and safely. You are also responsible for training

persons, who you allow to use the product, about safe

operation.

The warning system in this manual identifies

potential hazards and has special safety messages that

help you and others avoid personal injury, even death.

DANGER, WARNING and CAUTION are signal

words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended

precautions are not followed.

WARNING signals a hazard that may cause serious

injury or death if the recommended precautions are

not followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed.

Two other words are also used to highlight

information. “Important” calls attention to special

mechanical information and “Note” emphasizes

general information worthy of special attention.

The left and right side of the machine is determined

by sitting on the seat in the normal operator’s

position.

1

Contents

Page

Safety 3.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gasoline and Oil 11

. . . . . . . . . . . . . . . . . . . . . . . .

Recommended Gasoline

11

. . . . . . . . . . . . . .

Stabilizer/Conditioner 11

. . . . . . . . . . . . . . . .

Filling the Fuel Tank 11

. . . . . . . . . . . . . . . . .

Check Engine Oil Level 11

. . . . . . . . . . . . . . .

Assembly 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loose Parts 12

. . . . . . . . . . . . . . . . . . . . . . . . .

Install Castor Wheel

13

. . . . . . . . . . . . . . . . . .

Check Tire Pressure 13

. . . . . . . . . . . . . . . . . .

Secure PTO Cover 13

. . . . . . . . . . . . . . . . . . .

Activate the Battery 14

. . . . . . . . . . . . . . . . . .

Install Battery 15

. . . . . . . . . . . . . . . . . . . . . . .

Install Recycler) Baffles 16

. . . . . . . . . . . . . . .

Recycler) Operation 16

. . . . . . . . . . . . . . . . . .

Install Bagger and Discharge Baffles 17

. . . . .

Bagger Operation 17

. . . . . . . . . . . . . . . . . . . .

Operation 18

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Think Safety First 18

. . . . . . . . . . . . . . . . . . .

Controls 18

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Parking Brake 19

. . . . . . . . . . . . . . . . . . . . . . .

Starting and Stopping Engine 20

. . . . . . . . . .

Operating Power Take Off (PTO) 21

. . . . . . .

The Safety Interlock System 22

. . . . . . . . . . .

Instruments 22

. . . . . . . . . . . . . . . . . . . . . . . . .

Driving Forward or Backward 23

. . . . . . . . . .

Stopping the Machine 24

. . . . . . . . . . . . . . . .

Positioning the Seat 24

. . . . . . . . . . . . . . . . . .

Adjusting Height-of-Cut 25

. . . . . . . . . . . . . .

Adjusting Rollers

25

. . . . . . . . . . . . . . . . . . . .

Tilting the Mower 26

. . . . . . . . . . . . . . . . . . .

Dumping the Hopper 27

. . . . . . . . . . . . . . . . .

Pushing the Machine by Hand 28

. . . . . . . . . .

Page

Maintenance 29

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Interval Chart 29

. . . . . . . . . . . . . . . .

Air Cleaner 30

. . . . . . . . . . . . . . . . . . . . . . . . .

Engine Oil 32

. . . . . . . . . . . . . . . . . . . . . . . . .

Spark Plug 34

. . . . . . . . . . . . . . . . . . . . . . . . .

Greasing and Lubrication 35

. . . . . . . . . . . . . .

Replacing the Castor Wheel Fork Bushings

37

Servicing the Castor Wheels and Bearings 38

Replacing Push Arm Bushings

39

. . . . . . . . .

Cleaning the Cooling Systems

40

. . . . . . . . . .

Tire Pressure 40

. . . . . . . . . . . . . . . . . . . . . . . .

Fuel Filter 41

. . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel Tank 41

. . . . . . . . . . . . . . . . . . . . . . . . . .

Hydraulic System 42

. . . . . . . . . . . . . . . . . . . .

Adjust Motion Controls

44

. . . . . . . . . . . . . . .

Adjust Mowing Speed Reference Position 45

Replacing Power Take Off (PT

O) Belts

46

. . .

Replacing the Traction Belt 47

. . . . . . . . . . . .

Replacing the Blower Belt 47

. . . . . . . . . . . . .

Fuse 48

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Battery 49

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Cleaning Hopper Screens 50

. . . . . . . . . . . . . .

Cleaning the Hopper Full Sensor 50

. . . . . . . .

Cutting Blades

51

. . . . . . . . . . . . . . . . . . . . . .

Correcting Cutting Unit Mismatch 54

. . . . . .

Setting the Front-to-Rear Pitch 54

. . . . . . . . .

Setting the Side-to-Side Leveling 55

. . . . . . .

Wiring Diagram 56

. . . . . . . . . . . . . . . . . . . . .

Hydraulic Diagram 57

. . . . . . . . . . . . . . . . . . .

Cleaning and Storage 58

. . . . . . . . . . . . . . . . .

Troubleshooting 59

. . . . . . . . . . . . . . . . . . . . . . . . .

Contents

2

       

     

    

         

        

      

 

3

Safety

Safe

Operation Practices for

Ride-on (riding) Rotary

Lawnmower Machines

Training

1. Read the instructions carefully. Be familiar with

the controls and the proper use of the equipment.

2. Never allow children or people unfamiliar with

these instructions to use the lawnmower. Local

regulations may restrict the age of the operator.

3. Never mow while people, especially children, or

pets are nearby.

4. Keep in mind that the operator or user is

responsible for accidents or hazards occurring to

other people or their property.

5. Do not carry passengers.

6. All drivers should seek and obtain professional

and practical instruction. Such instruction should

emphasize:

• the need for care and concentration when

working with ride-on machines;

• control of a ride-on machine sliding on a

slope will not be regained by the application

of the brake. The main reasons for loss of

control are:

insufficient wheel grip;

being driven too fast;

inadequate braking;

the type of machine is unsuitable for its

task;

lack of awareness of the effects of

ground conditions, especially slopes;

incorrect hitching and load distribution.

Preparation

1. While mowing, always wear substantial

footwear and long trousers. Do not operate the

equipment when barefoot or wearing open

sandals.

2. Thoroughly inspect the area where the

equipment is to be used and remove all objects

which may be thrown by the machine.

3. WARNING – Petrol is highly flammable.

• Store fuel in containers specifically

designed for this purpose.

• Refuel outdoors only and do not smoke

while refuelling.

• Add fuel before starting the engine. Never

remove the cap of the fuel tank or add

petrol while the engine is running or when

the engine is hot.

• If petrol is spilled, do not attempt to start

the engine but move the machine away

from the are of spillage and avoid creating

any source of ignition until petrol vapors

have dissipated.

• Replace all fuel tanks and container caps

securely.

4.

Replace faulty silencers.

5. Before using, always visually inspect to see that

the blades, blade bolts and cutter assembly are

not worn or damaged. Replace worn or damaged

blades and bolts in sets to preserve balance.

6. On multi–bladed machines, take care as rotating

one blade can cause other blades to rotate.

Safety

4

Operation

1. Do not operate the engine in a confined space

where dangerous carbon monoxide fumes can

collect.

2. Mow only in daylight or in good artificial light.

3. Before attempting to start the engine, disengage

all blade attachment clutches and shift into

neutral.

4. Do not use on slopes of more than:

• Never mow side hills over 5

• Never mow uphill over 10

• Never mow downhill over 15

Note: Slope angle is calculated as in

5.4.2.3.2.

5. Remember there is no such thing as a “safe”

slope. Travel on grass slopes requires particular

care. To guard against overturning:

• do not stop or start suddenly when going up

or downhill;

•

engage clutch slowly

, always keep machine

in gear, especially when travelling

downhill;

• machine speeds should be kept low on

slopes and during tight turns;

• stay alert for bumps and hollows and other

hidden hazards;

• never mow across the face of the slope,

unless the lawnmower is designed for this

purpose.

6. Use care when pulling loads or using heavy

equipment.

• Use only approved drawbar hitch points.

• Limit loads to those you can safely control.

• Do not turn sharply. Use care when

reversing.

• Use counterweight(s) or wheel weights

when suggested in the instruction

handbook.

7. Watch out for traffic when crossing or near

roadways.

8. Stop the blades rotating before crossing surfaces

other than grass.

9. When using any attachments, never direct

discharge of material toward bystanders nor

allow anyone near the machine while in

operation.

10. Never operate the lawnmower with defective

guards, shields or without safety protective

devices in place.

11. Do not change the engine governor settings or

overspeed the engine. Operating the engine at

excessive speeds may increase the hazard of

personal injury.

12. Before leaving the operator’

s position:

• disengage the power take-off and lower the

attachments;

• change into neutral and set the parking

brake;

• stop the engine and remove the key.

13. Disengage drive to attachments, stop the engine,

and disconnect the spark plug wire(s) or remove

the ignition key

• before cleaning blockages or unclogging

chute;

• before checking, cleaning or working on the

lawnmower;

• after striking a foreign object. Inspect the

lawnmower for damage and make repairs

before restarting and operating the

equipment;

• if the machine starts to vibrate abnormally

(check immediately).

14. Disengage drive to attachments when

transporting or not in use.

Safety

5

15. Stop the engine and disengage drive to

attachment

• before refuelling;

• before removing the grass catcher;

• before making height adjustment unless

adjustment can be made from the operator’s

position.

16. Reduce the throttle setting during engine run-out

and, if the engine is provided with a shut-off

valve, turn the fuel off at the conclusion of

mowing.

Maintenance and storage

1. Keep all nuts, bolts and screws tight to be sure

the equipment is in safe working condition.

2. Never store the equipment with petrol in the tank

inside a building where fumes may reach an

open flame or spark.

3. Allow the engine to cool before storing in any

enclosure.

4. To reduce the fire hazard, keep the engine,

silencer, battery compartment and petrol storage

area free of grass, leaves, or excessive grease.

5. Check the grass catcher frequently for wear or

deterioration.

6. Replace worn or damaged parts for safety.

7. If the fuel tank has to be drained, this should be

done outdoors.

8. On multi-bladed machines, take care as rotating

one blade can cause other blades to rotate.

9. When machine is to be parked, stored or left

unattended, lower the cutting means unless a

positive mechanical lock is used.

Sound Pressure

This unit has an equivalent continuos A-weighted

sound pressure at the operator ear of: 90 dB(A), based

on measurements of identical machines per

81/1051/EEC.

Sound Power

This unit has a power level of: 105 dB(A)/1pW, based

on measurements of identical machines per Directive

84/539/EEC.

Vibration Level

This unit has a maximum hand-arm vibration level of

XX m/s

2

, and whole body vibration level of XX m/s

2

,

based on measurements of identical machines per EN

1032 and EN 1033.

Safety

6

Slope

Chart

Read all safety instructions on pages 3–10.

Safety

7

Safety

8

Symbols

Glossary

Safety alert triangle–

Read operator

’

s manual

Caustic liquids, chemical

burns to fingers or hand

First aid, flush with water

Fire, open light & smoking

prohibited

Eye protection must

be worn

Caution, toxic risk

Shut off engine & remove

key before preforming

Safety alert symbol

symbol within triangle

indicates a hazard

Consult technical manual

for proper service procedures

maintenance or repair work

Fire or open flame

Explosion

Do not dispose of lead

battery in garbage

Stay a safe distance

from the machine

Keep children a safe

distance from machine

Stay safe distance

from machine, out front Z

Keep children away

from battery

Stay a safe distance

from the machine

Hearing protection must

be worn

Safety

9

Symbols Glossary

Finger & hand engagement,

Severing of toes & fingers,

Thrown or flying objects,

Do not open or

remove safety shields

while engine is running

Blade retaining bolts must be

Torqued to 1

15–149 N.m

Hand & arm engagement,

rotary mower blade

whole body exposure

Thrown or flying objects,

whole body exposure

Keep guards and safety

sheilds in place

Severing of fingers or

hand-engine fan

Dismemberment, rider backing

Do not carry passengers

Hot surface, burns to

fingers or hands

Blade cutting element-

height adjustment

(mm)

Machine rollover

,

Machine rollover

, do not

Out Front Z

use on side hill slope

greater than 5 degrees

Dismemberment, Out Front Z

Stored energy hazard,

kickback or upward motion

Machine rollover

, do not

use on down hill slope

greater than 10 degrees

Machine rollover

, do not

use on up hill slope

greater than 15 degrees

belt drive

in forward motion

Whole body entanglement,

implement input drive line

Safety

10

Symbols Glossary

Fast

Slow

Decreasing/Increasing

Engine start

Engine stop

Choke

Oil Lubrication Point

Power take off (PT

O)

Alarm

Engage

Disengage

Brake system

Parking brake

On/Run

Battery

Off/stop

Elapsed Operating Hours

Engine run

11

Gasoline and Oil

Recommended

Gasoline

Use UNLEADED Regular Gasoline suitable for

automotive use (85 pump octane minimum). Leaded

regular gasoline may be used if unleaded regular is

not available.

IMPORTANT: Never use methanol, gasoline

containing methanol, or gasohol containing

more than 10% ethanol because the fuel

system could be damaged. Do not mix oil with

gasoline.

POTENTIAL HAZARD

• In certain conditions gasoline is extremely

flammable and highly explosive.

WHAT CAN HAPPEN

• A fire or explosion from gasoline can burn

you, others, and cause property damage.

HOW TO AV

OID THE HAZARD

• Use a funnel and fill the fuel tank outdoors,

in an open area, when the engine is cold.

Wipe up any gasoline that spills.

• Do not fill the fuel tank completely full.

Add gasoline to the fuel tank until the level

is 1/4” to 1/2” (6 mm to 13 mm) below the

bottom of the filler neck. This empty space

in the tank allows gasoline to expand.

• Never smoke when handling gasoline, and

stay away from an open flame or where

gasoline fumes may be ignited by a spark.

• Store gasoline in an approved container

and keep it out of the reach of children.

Never buy more than a 30-day supply of

gasoline.

Stabilizer/Conditioner

Add the correct amount of gas stabilizer/conditioner

to the gas. Using a stabilizer/conditioner in the

machine:

• Keeps gasoline fresh during storage

• Cleans the engine while it runs

• Eliminates gum-like buildup in the fuel system,

which causes hard starting

IMPORTANT: Never use fuel additives

containing methanol or ethanol.

Filling

the Fuel T

ank

1. Shut the engine off and set the parking brake.

2. Clean around the fuel tank cap and remove the

cap. Add unleaded regular gasoline until the

level is to the bottom of the filler neck. Do not

fill the neck completely full, this space in the

tank allows gasoline to expand.

3. Install fuel tank cap securely. Wipe up any

gasoline that may have spilled.

Check

Engine Oil Level

Before you start the engine and use the machine,

check the oil level in the engine crankcase; refer to

Checking Oil Level, page 32.

12

Assembly

Loose

Parts

Note: Use the chart below to verify all parts have been shipped.

DESCRIPTION QTY. USE

Wheel assembly–castor

Bolt 1/2–13 x 9” (228 mm)

Locknut 1/2–13

Washer 1/2” (13 mm)

Spacer

1

2

1

Install castor wheel

Battery

Battery clamp

Battery support rod

Wing nut 1/4–20

T

erminal boot

Bolt 1/4–20 x 3/4” (19 mm)

W

asher 1/4”

1

2

4

1

2

Install battery

Shoulder bolt

Locknut

1

Secure power take of

f (PT

O) cover

Recycler



baf

fle – left

Recycler



baf

fle – right

Carriage bolt 5/16–18 x 3/4” (19 mm)

Locknut 5/16”

1

6

Install Recycler



baf

fles

Key

Safety Booklet

Operator’

s Manual

Engine Operator

’

s Manual

Parts Catalog

Registration card

2

1

Read before operating machine

For ordering parts

Fill out and return to T

oro

Assembly

13

Install

Castor Wheel

1. Remove nut, washers, spacer and axle shaft from

fork (Fig. 1).

2. Jack up rear of unit and install rear wheel into

castor fork (Fig. 1).

3. Place wheel with spacer installed and washers

between fork and slide bolt through bearings

(Fig. 1).

4. Secure bolt with 1/2” locknut (Fig. 1).

5. Torque nut to 75 ft–lb (55 N⋅m).

6. Grease castor wheel bearings (Fig. 1).









m–3227





Figure 1

1. Wheel

assembly

2.

Bolt 1/2–13 x 9” (227 mm)

3. W

asher 1/2” (13 mm)

4. Spacer

5.

Locknut 1/2”

Check

T

ire Pressure

Check the air pressure in all tires: refer to Tire

Pressure in Maintenance section.

Secure

PT

O Cover

To lower mower refer to: Tilting the Mower in

Operation section.

Assembly

14

Activate

the Battery

Bulk electrolyte with 1.260 specific gravity must be

purchased from a local battery supply outlet.

1. Remove the battery from the machine.

IMPORTANT: Be careful not to damage the

long vent tube when removing the battery

box.

POTENTIAL HAZARD

• Battery electrolyte contains sulfuric acid

which is a deadly poison and it causes

severe burns.

WHAT CAN HAPPEN

• If you carelessly drink electrolyte you could

die or if it gets onto your skin you will be

burned.

HOW TO AV

OID THE HAZARD

• Do not drink electrolyte and avoid contact

with skin, eyes or clothing. Wear safety

glasses to shield your eyes and rubber

gloves to protect your hands.

• Fill the battery where clean water is always

available for flushing the skin.

• Follow all instructions and comply with all

safety messages on the electrolyte container.

2. Remove filler caps from the battery. Slowly pour

electrolyte into each cell until the electrolyte

level is up to the lower part of the tube (Fig. 2).

1

2

3

m–1262

Figure 2

1. Filler

caps

2. Electrolyte

3.

Lower part of the tube

Assembly

15

3. Leave the covers off and connect a 3 to 4 amp

battery charger to the battery posts (Fig. 3).

Charge the battery at a rate of 4 amperes or less

for 4 hours (12 volts).

4

1

2

3

m–1254

Figure 3

1. Positive

post

2.

Negative post

3.

Charger red (+) wire

4.

Charger black (–) wire

POTENTIAL

HAZARD

• Charging battery pr

oduces gasses.

WHAT CAN HAPPEN

• Battery gasses can explode.

HOW TO AV

OID THE HAZARD

• Keep cigarettes, sparks and flames away

from battery.

4. When the battery is fully charged, disconnect the

charger from the electrical outlet then from the

negative and positive battery posts (Fig. 3).

5. Slowly pour electrolyte into each cell until the

level is once again up to the “UPPER” line on

the battery case (Fig. 2) and install covers.

Install Battery

1. Fill battery with electrolyte and charge, refer to

BATTERY, page 49.

2. Position battery in tray with terminal posts

toward the engine (Fig. 4).

3. Slide the red terminal boot onto the red battery

cable.

4. Install the positive (red) battery cable to positive

(+) battery terminal then negative battery cable

to the negative (–) battery terminal. Secure

cables with (2) 1/4 x 3/4” (19 mm) bolts 1/4”

washers, 1/4” lock washers and 1/4” locknuts.

IMPORTANT: Route cables so they do not

contact metal edges or frame members.

5. Secure battery with (2) support rods, a battery

clamp and (2) 1/4” wing nuts. Position support

rods in mounting holes (Fig. 4). Tighten wing

nuts so battery is held securely in position and

will not slide. DO NOT OVERTIGHTEN.

1

m–3224

2

5

9

3

4

9

6

7

8

Figure 4

1. Battery

tray

2. T

erminal boot

3.

Positive battery cable

4.

Negative battery cable

5. Bolt

1/4–20 x

3/4” (19 mm)

6. Washer

1/4”

7.

Battery support rod

8.

Battery clamp

9.

Wing nut 1/4”

Assembly

16

Install

Recycler



Baffles

1. Remove spring below footrest, remove hairpin

cotter and clevis pin from latch and slide chute

out of blower opening (Fig. 5).

2. Tilt mower into the vertical position, refer to;

Tilting the Mower, page 26.

m-3564

4

2

1

3

Figure 5

1. Spring

2. Hairpin

cotter

3.

Clevis pin

4. Chute

3. Remove locknuts, carriage bolts, left and right

bagger baffles and left and right discharge baffles

from the mower (Fig. 8).

Note: Save all hardware for use when

installing bagger.

4. Locate the left and right Recycler



baf

fles inside

mower and secure with (6) 5/16–18 x 3/4”

(19 mm) carriage bolts, through from the top of

mower, and (6) 5/16” locknuts (Fig. 6).

1

m-3562

2

3

Figure 6

1. Recycler



baf

fle

2. Locknut

3.

Carriage bolt

Recycler



Operation

When operating the mower with Recycler



baffles

installed you must disengage the blower drive belt.

1. Stop the engine, remove the key and disconnect

the spark plug wire(s) from the spark plug(s).

2. Remove hairpin cotter and clevis pin from idler

arm (Fig. 7).

3. Push up on the spring loaded idler arm, behind

PTO (power take off) gearbox, to relax pressure

on blower belt (Fig. 7).

4. Align hole in idler arm with slot in frame and

insert clevis pin. Secure with hairpin cotter to

hold in position.

1

2

3

4

m-3548

Figure 7

1. Idler

arm

2.

Frame slot

3.

Clevis pin

4.

Hairpin cotter

Assembly

17

Install

Bagger and Discharge

Baffles

When changing between bagging and recycling

baffles must be removed and replaced

1. Tilt mower into the vertical position, refer to;

Tilting the Mower, page 26.

2. Remove locknuts, carriage bolts and Recycler



baffles from the mower (Fig. 6).

Note: Save all hardware for use when

installing Recycler



baffles.

3. Locate the left and right bagger baffles inside the

mower and secure with (6) 5/16–18 x 3/4”

(19 mm) carriage bolts, through from the top of

mower, and (6) 5/16” locknuts (Fig. 8).

4. Locate the left and right discharge baf

fles inside

the mower and secure with (4) 5/16–18 x 3/4”

(19 mm) carriage bolts, through from the top and

inside of mower, and (4) 5/16” locknut.(Fig. 8).

1

3

m-3756

2

4

3

2

4

Figure 8

1. Bagger

baf

fle

2.

Carriage bolt

5/16–18 x 3/4” (19 mm)

3.

Locknut 3/8”

4.

Discharge baf

fle

Bagger

Operation

When operating the mower with bagger baffles

installed you must engage the blower drive belt.

1. Stop the engine, remove the key and disconnect

the spark plug wire(s) from the spark plug(s).

2. Place belt around blower, idler and PTO pulleys.

3. Push up on the spring loaded idler arm, behind

PTO (power take off) gearbox, to relax pressure

on spring (Fig. 7).

4. Remove hairpin cotter and clevis pin from slot in

frame and allow idler to tension belt (Fig. 7).

5. Install hairpin cotter and clevis pin in outer hole

of idler arm for storage (Fig. 7).

1

2

3

4

m-3548

Figure 9

1. Idler

arm

2.

Frame slot

3.

Clevis pin

4.

Hairpin cotter

18

Operation

Think

Safety First

Please carefully read all the safety instructions on

pages 3–8. Knowing this information could help you,

your family, pets or bystanders avoid injury.

POTENTIAL HAZARD

• Loud sounds can cause ear damage and

loss of hearing.

WHAT CAN HAPPEN

• Ear damage or hearing loss may occur.

HOW TO AV

OID THE HAZARD

• Wear ear protection when operating this

machine.

Controls

Become familiar with all the controls (Fig. 1) before

you start the engine and operate the machine.

1

2

5

10

m–3729

3

8

9

7

4

6

Figure 1

1. Motion

control lever

2.

Parking brake

3.

Ignition switch

4. Throttle

5.

Power take of

f (PT

O)

6. Hourmeter

7. Choke

8.

Drink holder

9.

Fuel cap

10.

Hydro reservoir cap

Page is loading ...

Toro Z320 Z Master, With 122cm Mower and Bagger User manual

Toro Z320 Z Master, With 122cm Mower and Bagger User manual

Related papers

Other documents