VENTURE LIGHTING BO0003 LED Sensor Mounting Kit User manual

Type
User manual

VENTURE LIGHTING BO0003 LED Sensor Mounting Kit

This mounting kit is designed for use with VSolution fixtures, both with and without reflectors. It allows you to easily add a microwave motion sensor to your fixture, giving you the ability to automatically turn the light on when motion is detected and off when there is no motion. The sensor is fully programmable, so you can customize it to your specific needs.

Some potential use cases for this mounting kit include:

  • Security lighting: Mount the sensor on the outside of your home or business to deter intruders.
  • Convenience lighting: Mount the sensor in areas where you want the light to turn on automatically when you enter, such as closets, pantries, or garages.

VENTURE LIGHTING BO0003 LED Sensor Mounting Kit

This mounting kit is designed for use with VSolution fixtures, both with and without reflectors. It allows you to easily add a microwave motion sensor to your fixture, giving you the ability to automatically turn the light on when motion is detected and off when there is no motion. The sensor is fully programmable, so you can customize it to your specific needs.

Some potential use cases for this mounting kit include:

  • Security lighting: Mount the sensor on the outside of your home or business to deter intruders.
  • Convenience lighting: Mount the sensor in areas where you want the light to turn on automatically when you enter, such as closets, pantries, or garages.
VENTURE LIGHTING’S LED SENSOR MOUNTING KIT USER MANUAL
Before You Begin
Read These Instructions Completely and Carefully
(800) 451-2606 VentureLighting.com
Motion Sensor Installation Instructions
(VSolution Fixture with or without Reflector)
STEP 1: Remove terminal block cover and attach block base to mounting plate A with two M3 screws.
STEP 2: Attach mounting plate/terminal block assembly to fixture with two M4 screws.
Figure 1: Attach terminal block to fixture
Terminal Block
Microwave Motion Sensor
Mounting Plate - A
Mounting Plate - B
(Not used for fixture with reflector)
M3 Screws
M4 Screws
Wiring Caps
VSolution Fixture
(shown with Reflector)
M3 Screws
(800) 451-2606 VentureLighting.com
STEP 3: Attach sensor to fixture or reflector.
For Fixtures without Reflector:
A) Attach sensor to mounting plate B (M3 screws).
B) Attach mounting plate B to fixture (M4 screws).
For Fixtures with Reflector:
A) Unscrew thumbscrew enough to clear reflector lip.
B) Firmly pry open lever spring and place sensor on reflector. Slowly release spring against inside of
reflector to secure sensor.
C) Tighten thumbscrew to further secure sensor to reflector lip.
Figure 2: Attach sensor to fixture
(fixture without reflector)
Figure 3: Attach sensor to reflector Figure 4: Tighten thumbscrew
(800) 451-2606
6675 Parkland Blvd., Suite 100
Solon, Ohio 44139 USA
V
entureLighting.com
© 2022 Venture Li
g
htin
g
International Venture Li
g
htin
g
is a re
g
istered trademark of Venture Li
g
htin
g
International. BO0003-B
STEP 4: Route wires into terminal block though cord reliefs. Complete wiring inside terminal block as shown in diagram
below using provided wiring caps.
STEP 5: Attach terminal block cover. Program sensor according to instructions included with sensor.
120-277V
Figure 5: Wiring Diagram
Figure 6: Attach cover to terminal block
(fixture shown with reflector)
VENTURE LIGHTING’S LED SENSOR MOUNTING KIT MANUEL UTILISATEUR
Avant de commencer
Lisez ces instructions complètement et attentivement
(800) 451-2606 VentureLighting.com
Instructions d'installation du détecteur de mouvement
(VSolution Fixture avec ou sans réflecteur)
ÉTAPE 1: Retirer le couvercle du bornier et fixer la base du bloc à la plaque de montage A à l'aide de deux vis M3.
ÉTAPE 2: Fixez l'ensemble plaque de montage / bloc de jonction à l'appareil avec deux vis M4.
Figure 1: Fixez le bornier à l'appareil
Bornier
Capteur de mouvement à micro-ondes
Plaque de
monta
g
e - A
Plaque de montage - B
(Non utilisé pour luminaire avec
réflecteur)
Vis M3
Vis M4
Capuchons de câblage
VSolution Fixture
(montré avec réflecteur)
Vis M3
(800) 451-2606 VentureLighting.com
ÉTAPE 3: Fixez le capteur à l'appareil ou au réflecteur.
Pour les luminaires sans réflecteur:
A) Fixez le capteur à la plaque de montage B (vis M3).
B) Fixez la plaque de montage B à la fixation (vis M4).
Pour les luminaires avec réflecteur:
A) Dévissez suffisamment la vis pour dégager la lèvre du réflecteur.
B) Resserrer fermement le ressort du levier et placer le capteur sur le réflecteur. Relâcher lentement le
ressort contre l'intérieur du réflecteur pour fixer le capteur.
C) Serrez la vis pour fixer le capteur à la lèvre du réflecteur.
Figure 2: Attacher le capteur à l'appareil
(luminaire sans réflecteur)
Figure 3: Attacher le capteur au réflecteur Figure 4: Serrez la vis à oreilles
(800) 451-2606
6675 Parkland Blvd., Suite 100
Solon, Ohio 44139 USA
V
entureLighting.com
© 2022 Venture Li
g
htin
g
International Venture Li
g
htin
g
is a re
g
istered trademark of Venture Li
g
htin
g
International. BO0003-B
ÉTAPE 4: Acheminer les fils dans le bornier à travers les reliefs du cordon. Terminer le câblage à l'intérieur du bornier
comme indiqué sur le schéma ci-dessous en utilisant les bouchons de câblage fournis.
ÉTAPE 5: Fixez le couvercle du bornier. Programmez le capteur selon les instructions fournies avec le capteur.
120-277V
Bleu N Rouge +
Lin
Brun Lout jaune
Noir -
Charge
Variateur de vitesse
dimmable 1-10V
Figure 5: Schéma de câblage
Figure 6: Fixez le couvercle au bornier
(luminaire illustré avec réflecteur)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

VENTURE LIGHTING BO0003 LED Sensor Mounting Kit User manual

Type
User manual

VENTURE LIGHTING BO0003 LED Sensor Mounting Kit

This mounting kit is designed for use with VSolution fixtures, both with and without reflectors. It allows you to easily add a microwave motion sensor to your fixture, giving you the ability to automatically turn the light on when motion is detected and off when there is no motion. The sensor is fully programmable, so you can customize it to your specific needs.

Some potential use cases for this mounting kit include:

  • Security lighting: Mount the sensor on the outside of your home or business to deter intruders.
  • Convenience lighting: Mount the sensor in areas where you want the light to turn on automatically when you enter, such as closets, pantries, or garages.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI