Pro-Form XP 440 R User manual

Brand: Pro-Form

Model: XP 440 R

Category: Spin bikes

Type: User manual

Serial Number

Decal (under frame)

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

Model No. 831.21952.3

Serial No.

Write the serial number in the space

above for reference.

BIKE EXERCISER

User’s Manual

• Assembly

• Operation

• Maintenance

• Part List and Drawing

Sears, Roebuck and Co.

Hoffman Estates, IL 60179

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning

decal(s). If a decal is missing or illegible, call

1-888-533-1333 and request a free replacement

decal. Apply the decal in the location shown.

Note: The decal(s) may not be shown at actual size.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

HOW TO USE THE EXERCISE BIKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

90 DAY FULL WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your exercise bike before using your exercise bike.

Sears assumes no responsibility for personal injury or property damage sustained by or through the

use of this product.

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. Use the exercise bike only as described in

this manual.

3. It is the responsibility of the owner to ensure

that all users of the exercise bike are ade-

quately informed of all precautions.

4. The exercise bike is intended for home use

only. Do not use the exercise bike in a com-

mercial, rental, or institutional setting.

5. Keep the exercise bike indoors, away from

moisture and dust. Do not put the exercise

bike in a garage or covered patio, or near

water.

6. Place the exercise bike on a level surface,

with a mat beneath it to protect the floor or

carpet. Make sure that there is at least 2 ft.

(0.6 m) of clearance around the exercise bike.

7. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

8. Keep children under age 12 and pets away

from the exercise bike at all times.

9. Wear appropriate clothes while exercising;

do not wear loose clothes that could become

caught on the exercise bike. Always wear

athletic shoes for foot protection.

10. The heart rate monitor is not a medical

device. Various factors may affect the accu-

racy of heart rate readings. The heart rate

monitor is intended only as an exercise aid

in general.

11. The exercise bike should not be used by

persons weighing more than 275 lbs.

(125 kg).

12. Always keep your back straight while using

the exercise bike; do not arch your back.

13. The exercise bike does not have a freewheel;

the pedals will continue to move until the

flywheel stops. Reduce your pedaling speed

in a controlled way.

14. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN

Thank you for selecting the new PROFORM XP

™

440

R exercise bike. Cycling is an effective exercise for

increasing cardiovascular fitness, building endurance,

and toning the body. The 440 R exercise bike provides

a selection of features designed to make your workouts

at home more effective and enjoyable.

For your benefit, read this manual carefully before

you use the exercise bike. If you have questions after

reading this manual, please see the back cover of this

manual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Handlebar

Console

Wheel

Seat

Backrest

Pedal

Leveling Foot

Accessory Tray

Heart Rate Monitor

Adjustment Handle

Handle

Length: 4 ft. 5 in. (135 cm)

Width: 2 ft. (61 cm)

M10 Jam Nut

(57)–2

M8 x 20mm

Screw (55)–7

M8 x 40mm

Screw (58)–4

M6 x 36mm

Screw (69)–2

M4 x 16mm

Screw (61)–4

M5 x 16mm

Screw (60)–2

M10 x 80mm Screw/Bolt (54)–4

M8 x 30mm

Screw (56)–1

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the

key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it

has been preassembled. Extra parts may be included. If a part is missing, please call 1-888-533-1333.

• Assembly requires two persons.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until you complete all assembly steps.

• To identify small parts, see page 5.

• In addition to the included tool(s), assembly

requires the following tools:

one Phillips screwdriver

one adjustable wrench

Assembly may be easier if you have your own set

of wrenches. To avoid damaging parts, do not use

power tools.

ASSEMBLY

1. Orient the Rear Stabilizer (31) as shown.

While a second person lifts the rear of the Frame

(1), attach the Rear Stabilizer (31) to the Frame

with two M10 x 80mm Bolts (54) and two M10

Jam Nuts (57).

2. Orient the Front Stabilizer (32) as indicated by

the sticker.

While a second person lifts the front of the

Frame (1), attach the Front Stabilizer (32) to the

Frame with two M10 x 80mm Screws (54).

3. Orient the Upright (2) as shown. Have a second

person hold the Upright near the Frame (1).

Locate the wire tie inside the Upright (2). Tie the

lower end of the wire tie to the ends of the Main

Wire (53) and the Frame Pulse Wire (42).

Then, pull the other end of the wire tie upward

until the Main Wire (53) and the Frame Pulse

Wire (42) are routed completely through the

Upright (2).

4. Tip: Avoid pinching the wires. Set the Upright

(2) on the Frame (1).

Attach the Upright (2) to the Frame (1) with four

M8 x 20mm Screws (55).

5. Orient the Shield Cover (12) as shown. Then,

insert the Main Wire (53) and the Frame Pulse

Wire (42) upward through the Shield Cover.

Slide the Shield Cover (12) onto the Upright (2).

Then, press the Shield Cover into the Right and

Left Frame Shields (38, 39).

Wire Tie

Avoid pinching

the wires

6. Orient the Console Plate (11) as shown. Then,

insert the Main Wire (53) and the Frame Pulse

Wire (42) upward through the Console Plate.

Tip: Avoid pinching the wires. Insert the

Console Plate (11) into the Upright (2).

Orient the Handlebar (13) as shown. Tip: Avoid

pinching the wires. Attach the Handlebar and

the Console Plate (11) to the Upright (2) with two

M8 x 20mm Screws (55).

Avoid pinching

the wires

Battery

Cover

Battery

Cover

7. The Console (4) can use four D batteries

(not included); alkaline batteries are recom-

mended. IMPORTANT: If the Console has

been exposed to cold temperatures, allow it

to warm to room temperature before insert-

ing batteries. Otherwise, you may damage

the console displays or other electronic

components.

Remove the battery covers from the back of the

Console (4), and insert batteries into the battery

compartments. Make sure to orient the bat-

teries as shown by the diagrams inside the

battery compartments. Then, reattach the bat-

tery covers.

To purchase an optional power adapter, call

the telephone number on the cover of this

manual. To avoid damaging the console,

use only a manufacturer-supplied power

adapter. Plug one end of the power adapter into

the receptacle inside the battery compartment

on the console; plug the other end into an outlet

installed in accordance with all local codes and

ordinances.

Receptacle

8. While a second person holds the Console (4)

near the Upright (2), connect the wires on the

Console to the Main Wire (53) and to the Frame

Pulse Wires (42).

Insert the excess wire into the Upright (2) or into

the Console (4).

Tip: Avoid pinching the wires. Attach the

Console (4) to the Upright (2) with four M4 x

16mm Screws (61).

9. Orient the Adjustment Lever (15) as shown.

Attach the Adjustment Lever to the Brake Axle

(16) with two M5 x 16mm Screws (60).

10. Orient the Backrest Frame (5) as shown. Attach

the Backrest Frame to the Seat Carriage (3) with

an M8 x 20mm Screw (55) and an M8 x 30mm

Screw (56).

Avoid pinching

the wires

11. Orient the Seat (8) and Seat Frame (7) assembly

as shown. Attach the Seat Frame to the Seat

Carriage (3) with four M8 x 40mm Screws (58).

12. Orient the Backrest (6) as shown. Attach the

Backrest to the Backrest Frame (5) with two M6

36mm Screws (69).

Receptacle

13. Plug the Seat Frame Pulse Wire (22) into the

receptacle in the Left Seat Shield (41).

14. Identify the Right Pedal (36), which is marked

with an “R.”

Using an adjustable wrench, firmly tighten the

Right Pedal (36) clockwise into the right side of

the Crank (43).

Firmly tighten the Left Pedal (not shown) coun-

terclockwise into the left side of the Crank (not

shown).

Adjust the right strap to the desired position, and

press the ends of the straps onto the tabs on the

Right Pedal (36). Adjust the strap on the Left

Pedal (not shown) in the same way.

15. Make sure that all parts are properly tightened before you use the exercise bike. Note: After assembly is

completed, some extra parts may be left over. Place a mat beneath the exercise bike to protect the floor.

Strap

Tab

HOW TO USE THE EXERCISE BIKE

HOW TO ADJUST THE SEAT

The seat can be

adjusted forward

or backward to the

position that is the

most comfortable. To

adjust the seat, push

downward on the

adjustment handle,

slide the seat to the

desired position, and

then pull upward

on the adjustment

handle to lock the seat in place.

HOW TO ADJUST THE PEDAL STRAPS

To adjust the pedal

straps, first pull the

ends of the straps off

the tabs on the ped-

als. Adjust the straps

to the desired posi-

tion, and then press

the ends of the straps

onto the tabs.

HOW TO MOVE THE EXERCISE BIKE

To move the exercise

bike, hold the handle

on the rear stabilizer

and carefully lift it

until the exercise

bike can be moved

on the front wheels.

Carefully move the

exercise bike to the

desired location and

then lower it.

HOW TO LEVEL THE EXERCISE BIKE

If the exercise bike

rocks slightly on your

floor during use, turn

one or both of the

leveling feet on the

rear stabilizer until

the rocking motion is

eliminated.

Seat

Pedal

Strap

Tab

Handle

Leveling

Feet

Adjustment

Handle

FEATURES OF THE CONSOLE

The advanced console offers an array of features

designed to make your workouts more effective and

enjoyable.

When you use the manual mode of the console, you

can change the resistance of the pedals with the touch

of a button. As you exercise, the console will provide

continuous exercise feedback. You can even measure

your heart rate using the handgrip heart rate monitor.

The console offers eighteen preset workouts—nine

weight loss and nine performance workouts. Each

preset workout automatically changes the resistance

of the pedals and prompts you to vary your pedaling

speed as it guides you through an effective workout.

The console also features the iFit interactive workout

system, which enables the console to accept iFit cards

containing workouts designed to help you achieve

specific fitness goals.

For example, lose unwanted pounds with the 8-week

Weight Loss workout. iFit workouts control the resis-

tance of the pedals while the voice of a personal trainer

coaches you through your workouts. iFit cards are

available separately. To purchase iFit cards, go to

www.iFit.com or call 1-888-533-1333. iFit cards are

also available at select stores.

You can even connect your MP3 player or CD player

to the console sound system and listen to your favorite

music or audio books while you exercise.

To use the manual mode, see page 14. To use a

preset workout, see page 15. To use an iFit work-

out, see page 16. To use the sound system, see

page 17. To use the user mode, see page 17.

Note: Before using the console, make sure that batter-

ies are installed (see assembly step 7 on page 8).

If there is a sheet of plastic on the display, remove the

plastic.

CONSOLE DIAGRAM

HOW TO USE THE MANUAL MODE

1. Turn on the console.

Press any button or begin pedaling to turn on the

console.

When you turn on the console, the display will light.

A tone will sound and the console will be ready for

use.

2. Select the manual mode.

When you turn on the con-

sole, the manual mode will

be selected automatically.

If you have selected a

workout, reselect the manual

mode by pressing the 9 Wt.

Loss Workouts button or the

9 Perform. Workouts but-

ton repeatedly until a track

appears in the upper display.

3. Begin pedaling and change the resistance of

the pedals as desired.

As you pedal, change the

resistance of the pedals by

pressing the Resistance

increase and decrease

buttons.

Note: After you press the

buttons, it will take a moment

for the pedals to reach the

selected resistance level.

4. Follow your progress with the display.

The display can show the following workout

information:

Calories—This display mode will show the approx-

imate number of calories you have burned.

Distance—This display mode will show the dis-

tance that you have pedaled in miles or kilometers.

Profile—When a workout is selected, this display

mode will show a profile of the resistance settings

of the workout.

Pulse—This display mode will show your heart rate

when you use the handgrip heart rate monitor (see

step 5 on page 15).

Resistance (Res)—This display mode will show

the resistance level of the pedals for a few seconds

each time the resistance level changes.

Speed—This display mode will show your pedaling

speed in miles per hour or kilometers per hour.

Time—When the manual mode is selected, this

display mode will show the elapsed time. When a

workout is selected, this display mode will show the

time remaining in the workout.

Track—When the manual mode is selected, this

display mode will show a track representing 1/4

mile (400 m). As you exercise, indicators will

appear in succession around the track until the

entire track appears. The track will then disappear

and the indicators will again begin to appear in

succession.

Press the Display Mode

button repeatedly to view the

desired workout information.

To reset the display to zero,

press the On/Reset button.

Note: The console can show

pedaling speed and distance

in either miles or kilometers.

To view or change the unit

of measurement, see THE USER MODE on page

17.

Change the volume level of the

console by pressing the Volume

increase and decrease buttons.

5. Measure your heart rate if desired.

If there are sheets

of plastic on the

metal contacts

on the handgrip

heart rate moni-

tor, remove the

plastic. In addi-

tion, make sure

that your hands

are clean. To

measure your heart rate, hold the handgrip heart

rate monitor with your palms resting against the

contacts. Avoid moving your hands or gripping

the contacts tightly.

When your pulse is detected, a heart-shaped

symbol will flash in the display and then your heart

rate will be shown. For the most accurate heart rate

reading, hold the contacts for at least 15 seconds.

If your heart rate is not shown, make sure that your

hands are positioned as described. Be careful not

to move your hands excessively or to squeeze the

contacts tightly. For optimal performance, clean

the contacts using a soft cloth; never use alcohol,

abrasives, or chemicals to clean the contacts.

6. When you are finished exercising, the console

will turn off automatically.

If the pedals do not move for several seconds, a

series of tones will sound, the console will pause,

and the time will flash in the display.

If the pedals do not move for several minutes, the

console will turn off and the display will be reset.

HOW TO USE A PRESET WORKOUT

1. Turn on the console.

Press any button or begin pedaling to turn on the

console.

When you turn on the console, the display will light.

A tone will sound and the console will be ready for

use.

2. Select a preset workout.

To select a preset work-

out, press the 9 Wt. Loss

Workouts button or the 9

Perform. Workouts button

repeatedly until the num-

ber of the desired workout

appears in the lower display.

When you select a preset

workout, a profile of the

resistance levels of the

workout will scroll across

the upper display, the duration of the workout will

appear in the center display, and the number of the

workout will appear in the lower display.

3. Begin pedaling to start the workout.

Each workout is divided into several one-minute

segments. One resistance level and one goal

speed is programmed for each segment. Note: The

same resistance level and/or goal speed may be

programmed for consecutive segments.

During the workout, the workout profile will show

your progress (see the drawing above). The flash-

ing segment of the profile represents the current

segment of the workout. The height of the flashing

segment indicates the resistance level for the cur-

rent segment.

At the end of each segment of the workout, a

series of tones will sound and the next segment of

the profile will begin to flash. If a different resis-

tance level is programmed for the next segment,

the resistance level will appear in the display for

a few seconds to alert you. The resistance of the

pedals will then change.

Contacts

Profile

As you exercise, keep your

pedaling speed near the goal

speed for the current seg-

ment. The goal speed will

appear in the display when

the speed display mode is

selected.

IMPORTANT: The goal

speed is intended only to

provide motivation. Your

actual pedaling speed may be slower than the

goal speed. Make sure to pedal at a speed that

is comfortable for you.

If the resistance level for the current segment is

too high or too low, you can manually override

the setting by pressing the Resistance buttons.

IMPORTANT: When the current segment of the

workout ends, the pedals will automatically

adjust to the resistance level programmed for

the next segment.

If you stop pedaling for several seconds, a series of

tones will sound and the workout will pause.

To resume the workout, simply resume pedaling.

The workout will continue until the last segment

of the profile flashes and the last segment of the

workout ends.

4. Follow your progress with the display.

See step 4 on page 14.

5. Measure your heart rate if desired.

See step 5 on page 15.

6. When you are finished exercising, the console

will turn off automatically.

See step 6 on page 15.

HOW TO USE AN IFIT WORKOUT

iFit cards are available separately. To purchase iFit

cards, go to www.iFit.com or call 1-888-533-1333. iFit

cards are also available at select stores.

1. Turn on the console.

Press any button or begin pedaling to turn on the

console.

When you turn on the console, the display will light.

A tone will sound and the console will be ready for

use.

2. Insert an iFit card and select a workout.

To use an iFit workout, insert an iFit card into the

iFit slot; make sure that the iFit card is oriented so

that the metal contacts are face down and are fac-

ing the slot. When the iFit card is properly inserted,

the indicator next to the slot will light.

Next, select the desired workout on the iFit card by

pressing the increase and decrease buttons next to

the iFit slot.

A profile of the resistance levels of the workout

will scroll across the upper display, the duration of

the workout will appear in the center display, and

the number of the workout will appear in the lower

display.

A moment after you select a workout, the voice of a

personal trainer will begin guiding you through your

workout. iFit workouts function in the same way as

preset workouts. To use the workout, see steps 3 to

6 starting on page 15.

3. When you are finished exercising, remove the

iFit card.

Remove the iFit card when you are finished exer-

cising. Store the iFit card in a secure place.

iFit Slot

iFit Card

HOW TO USE THE SOUND SYSTEM

To play music or audio books through the console

sound system while you exercise, plug the included

audio cable into the jack on the console and into a jack

on your MP3 player or CD player; make sure that the

audio cable is fully plugged in.

Next, press the Play button on your

MP3 player or CD player. Adjust

the volume level using the Volume

increase and decrease buttons on the

console or the volume control on your

MP3 player or CD player.

THE USER MODE

The console features a user mode that allows you to

select a unit of measurement for the console and to

view console usage information.

1. Select the user mode.

To select the user mode,

press and hold down the

Display Mode button for a

few seconds until the user

mode information appears in

the display.

2. Select a unit of measurement if desired.

The console can show pedaling speed and dis-

tance in either miles or kilometers.

The upper display will show the selected unit of

measurement. An E for English miles or an M for

metric kilometers will appear in the upper display.

To change the unit of measurement, press the

Resistance decrease button repeatedly.

Note: When you replace the batteries, it may be

necessary to reselect the unit of measurement.

3. View console usage information if desired.

The center display will show the total number of

hours that the console has been used since the

exercise bike was purchased. The lower display

will show the total distance that the pedals have

moved since the exercise bike was purchased.

4. Exit the user mode.

Press the Display Mode button to exit the user

mode.

Inspect and tighten all parts of the exercise bike regu-

larly. Replace any worn parts immediately.

To clean the exercise bike, use a damp cloth and a

small amount of mild soap. IMPORTANT: To avoid

damage to the console, keep liquids away from

the console and keep the console out of direct

sunlight.

CONSOLE TROUBLESHOOTING

If the console display becomes dim, replace all the bat-

teries at the same time; most console problems are the

result of low batteries. See assembly step 7 on page

8 for replacement instructions.

If the console does not display your heart rate when

you use the handgrip heart rate monitor, see step 5 on

page 15.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the

reed switch should be adjusted.

To adjust the reed switch,

you must first remove the

Shield Cover (12). Using

a flat screwdriver, release

the tabs on the Shield

Cover, and then lift the

Shield Cover away from

the frame.

Next, locate the Reed Switch (46). Loosen, but do not

remove, the M4 x 16mm Screw (61).

Next, rotate the Pulley (43) until a Magnet (44) is

aligned with the Reed Switch (46). Slide the Reed

Switch slightly toward or away from the Magnet. Then,

retighten the M4 x 16mm Screw (61).

Rotate the Pulley (43) for a moment. Repeat these

actions until the console displays correct feedback.

When the reed switch is correctly adjusted, reattach

the shield cover.

MAINTENANCE AND TROUBLESHOOTING

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling,

even when the resistance is adjusted to the highest

level, the drive belt may need to be adjusted.

To adjust the drive belt, you must remove the right

pedal, the shield cover, and the right frame shield (see

the instructions below).

Using an adjustable wrench, turn the right pedal coun-

terclockwise and remove it.

See the HOW TO ADJUST THE REED SWITCH on

page 18 and remove the Shield Cover (12).

Next, see the EXPLODED DRAWING near the end of

this manual and remove the M4 x 16mm Screws (61)

from the Right and Left Frame Shields (38, 39). Then,

gently remove the Right Frame Shield.

Hold the two M8 Locknuts (67) and loosen the two

M8 x 16mm Flat Head Screws (73). Next, loosen the

M10 x 35mm Hex Screw (74) until the Drive Belt (49) is

tight. Then, hold the M8 Locknuts and tighten the M8 x

16mm Flat Head Screws.

Then, reattach the right frame shield, the top shield,

and the right pedal.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to

computer or peripheral devices. Changes or modifications not expressly approved by the party respon-

sible for compliance could void the user’s authority to operate this equipment.

EXERCISE GUIDELINES

These guidelines will help you to plan your exercise

program. For detailed exercise information, obtain a

reputable book or consult your physician. Remember,

proper nutrition and adequate rest are essential for

successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your

cardiovascular system, exercising at the proper inten-

sity is the key to achieving results. You can use your

heart rate as a guide to find the proper intensity level.

The chart below shows recommended heart rates for

fat burning and aerobic exercise.

To find the proper intensity level, find your age at the

bottom of the chart (ages are rounded off to the near-

est ten years). The three numbers listed above your

age define your “training zone.” The lowest number is

the heart rate for fat burning, the middle number is the

heart rate for maximum fat burning, and the highest

number is the heart rate for aerobic exercise.

Burning Fat—To burn fat effectively, you must exer-

cise at a low intensity level for a sustained period of

time. During the first few minutes of exercise, your

body uses carbohydrate calories for energy. Only after

the first few minutes of exercise does your body begin

to use stored fat calories for energy. If your goal is to

burn fat, adjust the intensity of your exercise until your

heart rate is near the lowest number in your training

zone. For maximum fat burning, exercise with your

heart rate near the middle number in your training

zone.

Aerobic Exercise—If your goal is to strengthen your

cardiovascular system, you must perform aerobic

exercise, which is activity that requires large amounts

of oxygen for prolonged periods of time. For aerobic

exercise, adjust the intensity of your exercise until your

heart rate is near the highest number in your training

zone.

WORKOUT GUIDELINES

Warming Up—Start with 5 to 10 minutes of stretch-

ing and light exercise. A warm-up increases your body

temperature, heart rate, and circulation in preparation

for exercise.

Training Zone Exercise—Exercise for 20 to 30 min-

utes with your heart rate in your training zone. (During

the first few weeks of your exercise program, do not

keep your heart rate in your training zone for longer

than 20 minutes.) Breathe regularly and deeply as you

exercise —never hold your breath.

Cooling Down—Finish with 5 to 10 minutes of stretch-

ing. Stretching increases the flexibility of your muscles

and helps to prevent post-exercise problems.

EXERCISE FREQUENCY

To maintain or improve your condition, complete three

workouts each week, with at least one day of rest

between workouts. After a few months of regular exer-

cise, you may complete up to five workouts each week,

if desired. Remember, the key to success is to make

exercise a regular and enjoyable part of your everyday

life.

WARNING: Before beginning this

or any exercise program, consult your physi-

cian. This is especially important for persons

over age 35 or persons with pre-existing

health problems.

The heart rate monitor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The heart rate monitor is

intended only as an exercise aid in determin-

ing heart rate trends in general.

Page is loading ...

Pro-Form XP 440 R User manual

Brand: Pro-Form

Model: XP 440 R

Category: Spin bikes

Type: User manual

Download PDF

report

Pro-Form XP 440 R User manual

Pro-Form XP 440 R User manual

Related papers

Other documents