ABB Relion 670 series Engineering Manual

Category
Software
Type
Engineering Manual

This manual is also suitable for

Relion
®
670 SERIES
670 series
Version 2.2 IEC
Engineering manual
Document ID: 1MRK 511 398-UEN
Issued: May 2019
Revision: E
Product version: 2.2
© Copyright 2017 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third party, nor
used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license and may
be used or disclosed only in accordance with the terms of such license.
This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/) This product includes cryptographic software written/
developed by: Eric Young ([email protected]) and Tim Hudson ([email protected]).
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or
other operational requirements are complied with. In particular, any risks in applications where
a system failure and/or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole responsibility of the
person or entity applying the equipment, and those so responsible are hereby requested to
ensure that all measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled
out. In case any errors are detected, the reader is kindly requested to notify the manufacturer.
Other than under explicit contractual commitments, in no event shall ABB be responsible or
liable for any loss or damage resulting from the use of this manual or the application of the
equipment.
Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility
(EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified
voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests
conducted by ABB in accordance with the product standard EN 60255-26 for the EMC directive,
and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The
product is designed in accordance with the international standards of the IEC 60255 series.
Table of contents
Section 1 Introduction.........................................................................................................5
1.1 This manual......................................................................................................................................... 5
1.2 Intended audience............................................................................................................................. 5
1.3 Product documentation................................................................................................................... 6
1.3.1 Product documentation set........................................................................................................ 6
1.3.2 Document revision history...........................................................................................................7
1.3.3 Related documents........................................................................................................................7
1.4 Document symbols and conventions.............................................................................................9
1.4.1 Symbols........................................................................................................................................... 9
1.4.2 Document conventions.............................................................................................................. 10
1.5 IEC 61850 edition 1 / edition 2 mapping..................................................................................... 10
Section 2 Engineering tool set......................................................................................... 21
2.1 Introduction.......................................................................................................................................21
2.2 IED engineering process.................................................................................................................22
Section 3 Engineering process.........................................................................................25
3.1 Workflow............................................................................................................................................25
Section 4 Setting up a project..........................................................................................27
4.1 PCM600 projects..............................................................................................................................27
4.2 Installing Connectivity packages.................................................................................................. 27
4.3 Setting technical key....................................................................................................................... 28
4.4 Setting up communication between PCM600 and the IED.....................................................30
4.5 Project managing in PCM600........................................................................................................35
4.6 Building a plant structure...............................................................................................................36
4.6.1 IEC 61850 naming conventions to identify an IED................................................................ 37
4.6.2 Changing the SCL version of an IED........................................................................................ 39
4.7 Inserting an IED................................................................................................................................ 39
4.7.1 Setting IED IP address in the project...................................................................................... 48
Section 5 Ethernet configuration tool............................................................................ 51
5.1 Introduction.......................................................................................................................................51
5.1.1 User interface............................................................................................................................... 51
5.2 Starting the Ethernet configuration tool....................................................................................55
Section 6 Protection and control engineering .............................................................. 57
6.1 Creating an application configuration with ACT.......................................................................57
6.1.1 Overview........................................................................................................................................ 57
6.1.2 Function blocks............................................................................................................................59
6.1.3 Signals and signal management.............................................................................................. 60
6.1.4 Conditional blocking functionality...........................................................................................61
6.1.5 Function block execution parameters.....................................................................................61
Table of contents
670 series 1
Engineering manual
© Copyright 2017 ABB. All rights reserved
6.1.6 Configuration parameters.........................................................................................................63
6.1.7 Connections and variables........................................................................................................ 64
6.1.8 Hardware channels..................................................................................................................... 64
6.1.9 Validation...................................................................................................................................... 65
6.2 Setting configuration and setting parameters in PST.............................................................66
6.2.1 Graphical Parameter Setting Tool............................................................................................67
6.3 Connecting signals in SMT.............................................................................................................68
Section 7 Local HMI engineering...................................................................................... 71
7.1 LED and function key engineering................................................................................................ 71
7.1.1 Local HMI engineering process................................................................................................. 71
7.1.2 LED operation modes................................................................................................................. 76
7.2 Single-line diagram engineering...................................................................................................80
7.2.1 Concept description to present and generate diagrams in graphical display editor...80
7.2.2 Supported single-line diagram symbols.................................................................................83
7.2.3 Bay configuration engineering................................................................................................. 88
7.3 Events and indications....................................................................................................................91
Section 8 IEC 61850 communication engineering......................................................... 93
8.1 IEC 61850 interface in the IED and tools..................................................................................... 93
8.1.1 Function view for IEC 61850 in PCM600................................................................................. 93
8.1.2 Access points............................................................................................................................... 93
8.1.3 IEC 61850 interface in IED..........................................................................................................94
8.1.3.1 GOOSE data exchange............................................................................................................ 95
8.1.4 Station configuration description file types......................................................................... 96
8.2 IEC 61850 engineering procedure................................................................................................ 96
8.2.1 IEC 61850 protocol references and pre-conditions..............................................................96
8.2.2 Sequence for engineering of IEC 61850 protocol................................................................. 96
8.3 Exporting SCL files from PCM600................................................................................................ 97
8.3.1 Exporting SCD files..................................................................................................................... 97
8.3.2 Exporting ICD or CID files..........................................................................................................98
8.4 Easy GOOSE engineering in the application configuration tool............................................ 99
8.4.1 User interface.............................................................................................................................100
8.4.2 Enable Easy GOOSE Engineering in PCM600.......................................................................104
8.4.3 Making GOOSE connections in the application configuration tool................................ 105
8.4.3.1 Create GOOSE connections via GOOSE receive functions............................................ 105
8.4.3.2 Create GOOSE connections via normal function blocks................................................ 107
8.4.3.3 Connect to GOOSE dialog window user interface – Extended Mode..........................108
8.4.3.4 Connecting to a IEC 61850 SCL data attribute from sending IED............................... 109
8.4.3.5 Easy GOOSE engineering when GOOSE is configured via IEC 61850
configuration protocol..........................................................................................................109
8.4.4 Deleting connections................................................................................................................ 110
8.4.5 Cut-Paste and Copy-Paste of ACT GOOSE variables.......................................................... 110
8.4.6 GOOSE Online Monitoring .......................................................................................................110
8.5 Engineering of vertical and horizontal communication in IET600.......................................110
8.6 Importing SCL files to PCM600................................................................................................... 112
8.6.1 Importing SCD files....................................................................................................................112
Table of contents
2 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
8.6.2 Importing ICD or CID files.........................................................................................................113
8.7 Writing IEC 61850 communication configuration to an IED.................................................. 113
Section 9 IEC 60870-5-103 communication engineering............................................ 115
9.1 Engineering in PCM600.................................................................................................................115
9.1.1 Settings for RS485 and optical serial communication.......................................................115
Section 10 DNP3 communication engineering................................................................117
10.1 Signal configuration user information.......................................................................................117
10.2 Adding setting groups...................................................................................................................117
10.3 Configuring DNP3 protocol signals............................................................................................ 119
10.4 Setting DNP3 signal parameters................................................................................................. 121
10.4.1 Configuring DNP3 class............................................................................................................ 122
Section 11 Flexible product naming................................................................................ 125
11.1 IEC 61850 Structure Mapping Tool............................................................................................. 125
11.1.1 User interface............................................................................................................................. 125
11.1.2 IED and Signal Naming Convention....................................................................................... 126
11.2 Importing the System Configuration Description file............................................................126
11.3 Starting the IEC 61850 Structure Mapping Tool...................................................................... 127
11.4 IEC 61850 Structure Mapping...................................................................................................... 128
11.4.1 IED mapping............................................................................................................................... 128
11.4.1.1 IED mapping in PCM600 Plant Structure...........................................................................128
11.4.1.2 IED mapping in the IEC 61850 Structure Mapping Tool................................................. 128
11.4.2 Data Attribute Mapping........................................................................................................... 130
11.4.2.1 Data Attribute Level Mapping.............................................................................................. 131
11.4.2.2 Data Object Level Mapping...................................................................................................131
11.4.2.3 Logical Node Level Mapping................................................................................................ 132
11.4.2.4 Excluding Data Attributes from Mapping......................................................................... 132
11.5 Setting the data attribute value..................................................................................................133
11.6 Validation.........................................................................................................................................133
11.7 Creating Template......................................................................................................................... 134
11.7.1 Creating a Mapping Template................................................................................................ 134
11.7.2 Applying Mapping Template on IED...................................................................................... 134
11.7.3 Exporting FPN templates.........................................................................................................135
11.8 Reporting and Printing..................................................................................................................135
Section 12 Glossary............................................................................................................137
12.1 Glossary............................................................................................................................................137
Table of contents
670 series 3
Engineering manual
© Copyright 2017 ABB. All rights reserved
4
Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v19
The engineering manual contains instructions on how to engineer the IEDs using the various
tools available within the PCM600 software. The manual provides instructions on how to set
up a PCM600 project and insert IEDs to the project structure. The manual also recommends a
sequence for the engineering of protection and control functions, as well as communication
engineering for IEC 61850.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v11
This manual addresses system and project engineers involved in the engineering process of a
project, and installation and commissioning personnel, who use technical data during
engineering, installation and commissioning, and in normal service.
The system engineer must have a thorough knowledge of protection and/or control systems,
protection and/or control equipment, protection and/or control functions and the configured
functional logics in the IEDs. The installation and commissioning personnel must have a basic
knowledge of handling electronic equipment.
1MRK 511 398-UEN E Section 1
Introduction
670 series 5
Engineering manual
© Copyright 2017 ABB. All rights reserved
1.3 Product documentation
1.3.1 Product documentation set
GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v16
IEC07000220-4-en.vsd
P
l
a
n
n
i
n
g
&
p
u
r
c
h
a
s
e
E
n
g
i
n
e
e
r
i
n
g
I
n
s
t
a
l
l
i
n
g
C
o
m
m
i
s
s
i
o
n
i
n
g
O
p
e
r
a
t
i
o
n
M
a
i
n
t
e
n
a
n
c
e
D
e
c
o
m
m
i
s
s
i
o
n
i
n
g
D
e
i
n
s
t
a
l
l
i
n
g
&
d
i
s
p
o
s
a
l
Application manual
Operation manual
Installation manual
Engineering manual
Communication
protocol manual
Cyber security
deployment guideline
Technical manual
Commissioning manual
IEC07000220 V4 EN-US
Figure 1: The intended use of manuals throughout the product lifecycle
The engineering manual contains instructions on how to engineer the IEDs using the various
tools available within the PCM600 software. The manual provides instructions on how to set
up a PCM600 project and insert IEDs to the project structure. The manual also recommends a
sequence for the engineering of protection and control functions, as well as communication
engineering for IEC 61850.
The installation manual contains instructions on how to install the IED. The manual provides
procedures for mechanical and electrical installation. The chapters are organized in the
chronological order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The manual
can also be used by system engineers and maintenance personnel for assistance during the
testing phase. The manual provides procedures for the checking of external circuitry and
energizing the IED, parameter setting and configuration as well as verifying settings by
secondary injection. The manual describes the process of testing an IED in a substation which
is not in service. The chapters are organized in the chronological order in which the IED should
be commissioned. The relevant procedures may be followed also during the service and
maintenance activities.
The operation manual contains instructions on how to operate the IED once it has been
commissioned. The manual provides instructions for the monitoring, controlling and setting of
the IED. The manual also describes how to identify disturbances and how to view calculated
and measured power grid data to determine the cause of a fault.
Section 1 1MRK 511 398-UEN E
Introduction
6 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
The application manual contains application descriptions and setting guidelines sorted per
function. The manual can be used to find out when and for what purpose a typical protection
function can be used. The manual can also provide assistance for calculating settings.
The technical manual contains operation principle descriptions, and lists function blocks, logic
diagrams, input and output signals, setting parameters and technical data, sorted per
function. The manual can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
The communication protocol manual describes the communication protocols supported by
the IED. The manual concentrates on the vendor-specific implementations.
The point list manual describes the outlook and properties of the data points specific to the
IED. The manual should be used in conjunction with the corresponding communication
protocol manual.
The cyber security deployment guideline describes the process for handling cyber security
when communicating with the IED. Certification, Authorization with role based access control,
and product engineering for cyber security related events are described and sorted by
function. The guideline can be used as a technical reference during the engineering phase,
installation and commissioning phase, and during normal service.
1.3.2
Document revision history
GUID-34B323E4-1319-4D42-80CE-29B0F2D36E2C v2
Document
revision
Date Product revision History
- 2017–05 2.2.0 First release for product version 2.2
A 2017–10 2.2.1 Ethernet ports with RJ45 connector added.
B 2018–03 2.2.1 Document enhancements and corrections
C 2018–06 2.2.2 Technical data updated for PSM. Case dimensions
updated.
D 2018–11 2.2.3 Functions CHMMHAI, VHMMHAI, DELVSPVC,
DELISPVC and DELSPVC added. Updates/
enhancements made to ZMFPDIS, ZMFCPDIS,
CCRBRF, REALCOMP, PTRSTHR and FNKEYMDx.
Ordering section updated.
E
2019-0
5
2.2.3 PTP enhancements and corrections
1.3.3 Related documents
GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v7
Documents related to REB670 Document numbers
Application manual 1MRK 505 370-UEN
Commissioning manual 1MRK 505 372-UEN
Product guide 1MRK 505 373-BEN
Technical manual 1MRK 505 371-UEN
Type test certificate 1MRK 505 373-TEN
1MRK 511 398-UEN E Section 1
Introduction
670 series 7
Engineering manual
© Copyright 2017 ABB. All rights reserved
Documents related to REC670 Document numbers
Application manual 1MRK 511 401-UEN
Commissioning manual 1MRK 511 403-UEN
Product guide 1MRK 511 404-BEN
Technical manual 1MRK 511 402-UEN
Type test certificate 1MRK 511 404-TEN
Documents related to RED670 Document numbers
Application manual 1MRK 505 376-UEN
Commissioning manual 1MRK 505 378-UEN
Product guide 1MRK 505 379-BEN
Technical manual 1MRK 505 377-UEN
Type test certificate 1MRK 505 379-TEN
Documents related to REG670 Document numbers
Application manual 1MRK 502 071-UEN
Commissioning manual 1MRK 502 073-UEN
Product guide 1MRK 502 074-BEN
Technical manual 1MRK 502 072-UEN
Type test certificate 1MRK 502 074-TEN
Documents related to REL670 Document numbers
Application manual 1MRK 506 369-UEN
Commissioning manual 1MRK 506 371-UEN
Product guide 1MRK 506 372-BEN
Technical manual 1MRK 506 370-UEN
Type test certificate 1MRK 506 372-TEN
Documents related to RET670 Document numbers
Application manual 1MRK 504 163-UEN
Commissioning manual 1MRK 504 165-UEN
Product guide 1MRK 504 166-BEN
Technical manual 1MRK 504 164-UEN
Type test certificate 1MRK 504 166-TEN
Documents related to RES670 Document numbers
Application manual 1MRK 511 407-UEN
Commissioning manual 1MRK 511 409-UEN
Product guide 1MRK 511 410-BEN
Technical manual 1MRK 511 408-UEN
Type test certificate 1MRK 511 410-TEN
Section 1 1MRK 511 398-UEN E
Introduction
8 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
Documents related to RER670 Document numbers
Application manual 1MRK 506 375-UEN
Commissioning manual 1MRK 506 377-UEN
Product guide 1MRK 506 378-BEN
Technical manual 1MRK 506 376-UEN
Type test certificate 1MRK 506 378-TEN
670 series manuals Document numbers
Operation manual 1MRK 500 127-UEN
Engineering manual 1MRK 511 398-UEN
Installation manual 1MRK 514 026-UEN
Communication protocol manual, DNP3 1MRK 511 391-UUS
Communication protocol manual, IEC 60870-5-103 1MRK 511 394-UEN
Communication protocol manual, IEC 61850 Edition 1 1MRK 511 392-UEN
Communication protocol manual, IEC 61850 Edition 2 1MRK 511 393-UEN
Communication protocol manual, LON 1MRK 511 395-UEN
Communication protocol manual, SPA 1MRK 511 396-UEN
Point list manual, DNP3 1MRK 511 397-UUS
Accessories guide 1MRK 514 012-BEN
Cyber security deployment guideline 1MRK 511 399-UEN
Connection and Installation components 1MRK 513 003-BEN
Test system, COMBITEST 1MRK 512 001-BEN
Application guide, Communication set-up 1MRK 505 382-UEN
1.4 Document symbols and conventions
1.4.1 Symbols
GUID-2945B229-DAB0-4F15-8A0E-B9CF0C2C7B15 v13
The electrical warning icon indicates the presence of a hazard which could
result in electrical shock.
The warning icon indicates the presence of a hazard which could result in
personal injury.
The caution hot surface icon indicates important information or warning about
the temperature of product surfaces.
The caution icon indicates important information or warning related to the
concept discussed in the text. It might indicate the presence of a hazard which
could result in corruption of software or damage to equipment or property.
1MRK 511 398-UEN E Section 1
Introduction
670 series 9
Engineering manual
© Copyright 2017 ABB. All rights reserved
The information icon alerts the reader of important facts and conditions.
The tip icon indicates advice on, for example, how to design your project or
how to use a certain function.
Although warning hazards are related to personal injury, it is necessary to understand that
under certain operational conditions, operation of damaged equipment may result in
degraded process performance leading to personal injury or death. It is important that the
user fully complies with all warning and cautionary notices.
1.4.2 Document conventions
GUID-96DFAB1A-98FE-4B26-8E90-F7CEB14B1AB6 v8
• Abbreviations and acronyms in this manual are spelled out in the glossary. The glossary
also contains definitions of important terms.
• Push button navigation in the LHMI menu structure is presented by using the push button
icons.
For example, to navigate between the options, use
and .
• HMI menu paths are presented in bold.
For example, select Main menu/Settings.
• LHMI messages are shown in Courier font.
For example, to save the changes in non-volatile memory, select Yes and press .
• Parameter names are shown in italics.
For example, the function can be enabled and disabled with the
Operation
setting.
• Each function block symbol shows the available input/output signal.
• the character ^ in front of an input/output signal name indicates that the signal
name may be customized using the PCM600 software.
• the character * after an input signal name indicates that the signal must be
connected to another function block in the application configuration to achieve a
valid application configuration.
• Dimensions are provided both in inches and millimeters. If it is not specifically mentioned
then the dimension is in millimeters.
1.5 IEC 61850 edition 1 / edition 2 mapping
GUID-C5133366-7260-4C47-A975-7DBAB3A33A96 v7
Function block names are used in ACT and PST to identify functions. Respective function block
names of Edition 1 logical nodes and Edition 2 logical nodes are shown in the table below.
Table 1: IEC 61850 edition 1 / edition 2 mapping
Function block name
Edition 1 logical nodes Edition 2 logical nodes
AEGPVOC AEGGAPC AEGPVOC
AGSAL AGSAL
SECLLN0
AGSAL
ALMCALH ALMCALH ALMCALH
ALTIM - ALTIM
ALTMS - ALTMS
ALTRK - ALTRK
BCZPDIF BCZPDIF BCZPDIF
Table continues on next page
Section 1 1MRK 511 398-UEN E
Introduction
10 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
Function block name Edition 1 logical nodes Edition 2 logical nodes
BCZSPDIF BCZSPDIF BCZSPDIF
BCZTPDIF BCZTPDIF BCZTPDIF
BDCGAPC SWSGGIO BBCSWI
BDCGAPC
BDZSGAPC BBS6LLN0
BDZSGAPC
LLN0
BDZSGAPC
BFPTRC_F01 BFPTRC BFPTRC
BFPTRC_F02 BFPTRC BFPTRC
BFPTRC_F03 BFPTRC BFPTRC
BFPTRC_F04 BFPTRC BFPTRC
BFPTRC_F05 BFPTRC BFPTRC
BFPTRC_F06 BFPTRC BFPTRC
BFPTRC_F07 BFPTRC BFPTRC
BFPTRC_F08 BFPTRC BFPTRC
BFPTRC_F09 BFPTRC BFPTRC
BFPTRC_F10 BFPTRC BFPTRC
BFPTRC_F11 BFPTRC BFPTRC
BFPTRC_F12 BFPTRC BFPTRC
BFPTRC_F13 BFPTRC BFPTRC
BFPTRC_F14 BFPTRC BFPTRC
BFPTRC_F15 BFPTRC BFPTRC
BFPTRC_F16 BFPTRC BFPTRC
BFPTRC_F17 BFPTRC BFPTRC
BFPTRC_F18 BFPTRC BFPTRC
BFPTRC_F19 BFPTRC BFPTRC
BFPTRC_F20 BFPTRC BFPTRC
BFPTRC_F21 BFPTRC BFPTRC
BFPTRC_F22 BFPTRC BFPTRC
BFPTRC_F23 BFPTRC BFPTRC
BFPTRC_F24 BFPTRC BFPTRC
BICPTRC_01 BICPTRC BICPTRC
BICPTRC_02 BICPTRC BICPTRC
BICPTRC_03 BICPTRC BICPTRC
BICPTRC_04 BICPTRC BICPTRC
BICPTRC_05 BICPTRC BICPTRC
BRCPTOC BRCPTOC BRCPTOC
BRPTOC BRPTOC BRPTOC
BTIGAPC B16IFCVI BTIGAPC
BUSPTRC_B1 BUSPTRC
BBSPLLN0
BUSPTRC
BUSPTRC_B2 BUSPTRC BUSPTRC
BUSPTRC_B3 BUSPTRC BUSPTRC
BUSPTRC_B4 BUSPTRC BUSPTRC
Table continues on next page
1MRK 511 398-UEN E Section 1
Introduction
670 series 11
Engineering manual
© Copyright 2017 ABB. All rights reserved
Function block name Edition 1 logical nodes Edition 2 logical nodes
BUSPTRC_B5 BUSPTRC BUSPTRC
BUSPTRC_B6 BUSPTRC BUSPTRC
BUSPTRC_B7 BUSPTRC BUSPTRC
BUSPTRC_B8 BUSPTRC BUSPTRC
BUSPTRC_B9 BUSPTRC BUSPTRC
BUSPTRC_B10 BUSPTRC BUSPTRC
BUSPTRC_B11 BUSPTRC BUSPTRC
BUSPTRC_B12 BUSPTRC BUSPTRC
BUSPTRC_B13 BUSPTRC BUSPTRC
BUSPTRC_B14 BUSPTRC BUSPTRC
BUSPTRC_B15 BUSPTRC BUSPTRC
BUSPTRC_B16 BUSPTRC BUSPTRC
BUSPTRC_B17 BUSPTRC BUSPTRC
BUSPTRC_B18 BUSPTRC BUSPTRC
BUSPTRC_B19 BUSPTRC BUSPTRC
BUSPTRC_B20 BUSPTRC BUSPTRC
BUSPTRC_B21 BUSPTRC BUSPTRC
BUSPTRC_B22 BUSPTRC BUSPTRC
BUSPTRC_B23 BUSPTRC BUSPTRC
BUSPTRC_B24 BUSPTRC BUSPTRC
BUTPTRC_B1 BUTPTRC
BBTPLLN0
BUTPTRC
BUTPTRC_B2 BUTPTRC BUTPTRC
BUTPTRC_B3 BUTPTRC BUTPTRC
BUTPTRC_B4 BUTPTRC BUTPTRC
BUTPTRC_B5 BUTPTRC BUTPTRC
BUTPTRC_B6 BUTPTRC BUTPTRC
BUTPTRC_B7 BUTPTRC BUTPTRC
BUTPTRC_B8 BUTPTRC BUTPTRC
BZISGGIO BZISGGIO BZISGAPC
BZITGGIO BZITGGIO BZITGAPC
BZNPDIF_Z1 BZNPDIF BZNPDIF
BZNPDIF_Z2 BZNPDIF BZNPDIF
BZNPDIF_Z3 BZNPDIF BZNPDIF
BZNPDIF_Z4 BZNPDIF BZNPDIF
BZNPDIF_Z5 BZNPDIF BZNPDIF
BZNPDIF_Z6 BZNPDIF BZNPDIF
BZNSPDIF_A BZNSPDIF BZASGAPC
BZASPDIF
BZNSGAPC
BZNSPDIF
BZNSPDIF_B BZNSPDIF BZBSGAPC
BZBSPDIF
BZNSGAPC
BZNSPDIF
Table continues on next page
Section 1 1MRK 511 398-UEN E
Introduction
12 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
Function block name Edition 1 logical nodes Edition 2 logical nodes
BZNTPDIF_A BZNTPDIF BZATGAPC
BZATPDIF
BZNTGAPC
BZNTPDIF
BZNTPDIF_B BZNTPDIF BZBTGAPC
BZBTPDIF
BZNTGAPC
BZNTPDIF
CBPGAPC CBPLLN0
CBPMMXU
CBPPTRC
HOLPTOV
HPH1PTOV
PH3PTUC
PH3PTOC
RP3PDOP
CBPMMXU
CBPPTRC
HOLPTOV
HPH1PTOV
PH3PTOC
PH3PTUC
RP3PDOP
CCPDSC CCRPLD CCPDSC
CCRBRF CCRBRF CCRBRF
CCRWRBRF CCRWRBRF CCRWRBRF
CCSRBRF CCSRBRF CCSRBRF
CCSSPVC CCSRDIF CCSSPVC
CMMXU CMMXU CMMXU
CMSQI CMSQI CMSQI
COUVGAPC COUVLLN0
COUVPTOV
COUVPTUV
COUVPTOV
COUVPTUV
CVGAPC GF2LLN0
GF2MMXN
GF2PHAR
GF2PTOV
GF2PTUC
GF2PTUV
GF2PVOC
PH1PTRC
GF2MMXN
GF2PHAR
GF2PTOV
GF2PTUC
GF2PTUV
GF2PVOC
PH1PTRC
CVMMXN CVMMXN CVMMXN
D2PTOC D2LLN0
D2PTOC
PH1PTRC
D2PTOC
PH1PTRC
DPGAPC DPGGIO DPGAPC
DRPRDRE DRPRDRE DRPRDRE
ECPSCH ECPSCH ECPSCH
ECRWPSCH ECRWPSCH ECRWPSCH
EF2PTOC EF2LLN0
EF2PTRC
EF2RDIR
GEN2PHAR
PH1PTOC
EF2PTRC
EF2RDIR
GEN2PHAR
PH1PTOC
EF4PTOC EF4LLN0
EF4PTRC
EF4RDIR
GEN4PHAR
PH1PTOC
EF4PTRC
EF4RDIR
GEN4PHAR
PH1PTOC
EFPIOC EFPIOC EFPIOC
EFRWPIOC EFRWPIOC EFRWPIOC
ETPMMTR ETPMMTR ETPMMTR
Table continues on next page
1MRK 511 398-UEN E Section 1
Introduction
670 series 13
Engineering manual
© Copyright 2017 ABB. All rights reserved
Function block name Edition 1 logical nodes Edition 2 logical nodes
FDPSPDIS FDPSPDIS FDPSPDIS
FMPSPDIS FMPSPDIS FMPSPDIS
FRPSPDIS FPSRPDIS FPSRPDIS
FTAQFVR FTAQFVR FTAQFVR
FUFSPVC SDDRFUF FUFSPVC
SDDSPVC
GENPDIF GENPDIF GENGAPC
GENPDIF
GENPHAR
GENPTRC
GOPPDOP GOPPDOP GOPPDOP
PH1PTRC
GRPTTR GRPTTR GRPTTR
GSPTTR GSPTTR GSPTTR
GUPPDUP GUPPDUP GUPPDUP
PH1PTRC
HZPDIF HZPDIF HZPDIF
INDCALCH INDCALH INDCALH
ITBGAPC IB16FCVB ITBGAPC
L3CPDIF L3CPDIF L3CGAPC
L3CPDIF
L3CPHAR
L3CPTRC
L4CPDIF L4CLLN0
L4CPDIF
L4CPTRC
LLN0
L4CGAPC
L4CPDIF
L4CPSCH
L4CPTRC
L4UFCNT L4UFCNT L4UFCNT
L6CPDIF L6CPDIF L6CGAPC
L6CPDIF
L6CPHAR
L6CPTRC
LAPPGAPC LAPPLLN0
LAPPPDUP
LAPPPUPF
LAPPPDUP
LAPPPUPF
LCCRPTRC LCCRPTRC LCCRPTRC
LCNSPTOC LCNSPTOC LCNSPTOC
LCNSPTOV LCNSPTOV LCNSPTOV
LCP3PTOC LCP3PTOC LCP3PTOC
LCP3PTUC LCP3PTUC LCP3PTUC
LCPTTR LCPTTR LCPTTR
LCZSPTOC LCZSPTOC LCZSPTOC
LCZSPTOV LCZSPTOV LCZSPTOV
LD0LLN0 LLN0 -
LDLPSCH LDLPDIF LDLPSCH
LDRGFC STSGGIO LDRGFC
LEXPDIS LEXPDIS LEXPDIS
LEXPTRC
LFPTTR LFPTTR LFPTTR
Table continues on next page
Section 1 1MRK 511 398-UEN E
Introduction
14 670 series
Engineering manual
© Copyright 2017 ABB. All rights reserved
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152

ABB Relion 670 series Engineering Manual

Category
Software
Type
Engineering Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI