Allen-Bradley FactoryTalk Analytics for Devices Quick start guide

Allen-Bradley
Brand
Allen-Bradley
Model
FactoryTalk Analytics for Devices
Category
Networking
Type
Quick start guide

Allen-Bradley FactoryTalk Analytics for Devices is an analytical appliance that monitors the status of control devices on an EtherNet/IP network. It can detect EtherNet/IP devices automatically, analyze device data for display on device-specific dashboards, and perform system-level health and diagnostics.

The appliance is easy to set up and use. Simply connect it to your network and power it on. The appliance will automatically detect EtherNet/IP devices on the network and begin collecting data. You can then access the appliance's web interface to view data and configure settings.

FactoryTalk Analytics for Devices can help you to improve the performance and reliability of your control system. By monitoring the status of your devices, the appliance can identify potential problems before they cause downtime. The appliance can also provide you with insights into how your devices are performing, so that you can make informed decisions about how to improve their efficiency.

Allen-Bradley FactoryTalk Analytics for Devices is an analytical appliance that monitors the status of control devices on an EtherNet/IP network. It can detect EtherNet/IP devices automatically, analyze device data for display on device-specific dashboards, and perform system-level health and diagnostics.

The appliance is easy to set up and use. Simply connect it to your network and power it on. The appliance will automatically detect EtherNet/IP devices on the network and begin collecting data. You can then access the appliance's web interface to view data and configure settings.

FactoryTalk Analytics for Devices can help you to improve the performance and reliability of your control system. By monitoring the status of your devices, the appliance can identify potential problems before they cause downtime. The appliance can also provide you with insights into how your devices are performing, so that you can make informed decisions about how to improve their efficiency.

Quick Start
FactoryTalk Analytics for Devices
FactoryTalk® Analytics for Devices is an analytical appliance that monitors the status of control devices on an
EtherNet/IP network. The appliance:
• Detects EtherNet/IP devices automatically
• Analyzes device data for display on device-specific dashboards
• Performs system-level health and diagnostics
What’s in the Box
To install the appliance, you need:
• 24V DC power supply
• RJ45 Ethernet cable
Item Description
1 24V DC power input
2 ETH1 Ethernet port
3 ETH2 Ethernet port
4 Power button
1 23
4
2 Rockwell Automation Publication 6200-QS001C-EN-P - May 2018
FactoryTalk Analytics for Devices
Set Up the Appliance
Connect the Appliance to a Computer
1. Connect the ETH1 port of the appliance directly to an Ethernet port on a computer.
You use the computer to configure the appliance.
2. Connect 24V DC power to the appliance.
Optional:
• 6200V-MPS4: 90 W, 24V AC-to-DC power adapter
• 6200V-DCCONN: DC power mating connector housing
Open the power connector to expose the screws so that you can insert the input wires.
For additional mounting and accessory information, see VersaView 5000 ThinManager Thin Clients and Industrial
Computers User Manual, publication 6200-UM001
.
IMPORTANT Do not press the power button. The appliance powers up when you connect the power cable.
Pin Description
10V input
2Functional Earth
3 +24V DC input
1
2
3
32790-M
Rockwell Automation Publication 6200-QS001C-EN-P - May 2018 3
FactoryTalk Analytics for Devices
Access a Browser to Configure the Appliance
The appliance works best with the current versions of these browsers:
• Internet Explorer
• Google Chrome
1. Change the IP address of the computer to be in the same range as the default IP address of the appliance.
For example, set the IP address of the computer to 192.168.100.20 and the subnet mask to 255.255.255.0.
a. From the Windows Control Panel or System Tray, choose Network and Sharing Center > Change adapter
settings.
b. Right-click the Local Area Connection that is connected to the appliance and select Properties.
c. Double-click the Internet Protocol Version 4 (TCP/IPv4) connection.
d. Choose Use the following address and enter the IP address and subnet mask.
e. Click OK to save the changes.
IMPORTANT The default IP address of the appliance is 192.168.100.1.
a
b
c
d
4 Rockwell Automation Publication 6200-QS001C-EN-P - May 2018
FactoryTalk Analytics for Devices
2. Open a web browser on the computer and go to: http://192.168.100.1
3. Click Get Started and follow the browser prompts to configure the appliance:
4. View and accept the end-user license agreements.
Setting Description
Appliance host name Define the network name of the appliance.
Date, time, and time zone Set the time stamp for any events the appliance detects in the target network.
Connectivity options Select system update and data synchronization options.
Appliance network options Define network settings for the appliance within the target network.
Important: We recommend that you set a static IP address for the appliance. A DHCP
configuration takes longer to propagate.
Security Define the administrator password and access the security certificate.
Rockwell Automation Publication 6200-QS001C-EN-P - May 2018 5
FactoryTalk Analytics for Devices
The final configuration screen displays a link to access the appliance web services.
5. To complete the configuration, click Finish and Shut Down.
The appliance shuts down.
6. When all status indicators stop flashing (the Power indicator changes from solid green to off ), disconnect the
power and network cables.
7. Follow the steps in the next section to connect the appliance to the target network.
Connect the Appliance to the Target Network
Connect the Appliance to the Target Network
As many as 6 workstations can simultaneously access the same appliance. The workstations do not require any client
licenses.
IMPORTANT Do not press the power button. Disconnect power by removing the power cable.
T1
246
T2 T3
1
1314 23 2495 96 1T11T2
23456
E3 Plus
TEST/
RESET
NETWORK
STATUS
TRIP
WARN
1A0FB851
3.003 B
OUT A OUT B
IN 1
IN 2
D
NET
S/N
FRN SER
LSD
MSD
0
82
46
JWM
0
82
46
PWR
HDD
DISPLAY PORT
COM 1
USB 3.0
ETH 1ETH 2
VGA
24VDC
USB 2.0
REDUNDANCY MODULE
OK
COMM
PRI
CAN_H
ADDRESS/ERROR
SHIELD
CAN_L
V-
V+
MODULE
REWORK
0
1
2
3
0
1
2
3
4
5
6
7
TTL
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
DC INPUT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Appliance
Client Workstation
CompactLogix™ Controller
ControlLogix® Controller
E300™ Electronic
Overload Relay
PowerFlex® 525 Drive
6 Rockwell Automation Publication 6200-QS001C-EN-P - May 2018
FactoryTalk Analytics for Devices
Power Up the Appliance
Reconnect the power cable.
Get Started
Access the appliance web services from a web browser at: http://shelbyaddress/
where shelbyaddress = the IP address you configured for the appliance in the configuration steps.
The appliance connects to the first 100 devices it finds on the target network and displays the System Feed.
Available Tabs
IMPORTANT Do not press the power button. The appliance powers up when you connect the power cable.
IMPORTANT To avoid problems with the appliance, click Shut Down Appliance on the Control Panel to turn off the appliance.
Tab Description
System Feed Shows the higher-level stories of the devices in your system.
Explorer Displays dashboards for the devices in your system. Select a device to display data that is specific to that device.
Action Deck Displays action cards for the conditions that the appliance reports.
Click Vote Up or swipe to the right from your touch device to vote it up if the device is relevant to you.
Click Vote Down or swipe to the left if the device is not relevant to you. After six consecutive swipes to the left, the
appliance no longer displays the information for that device. The appliance learns what is most important to you.
Item Description
1 Power button
2Power indicator
3 Hard disk drive (HDD) activity indicator
1
2
3
Rockwell Automation Publication 6200-QS001C-EN-P - May 2018 7
FactoryTalk Analytics for Devices
Ask questions through the Ask Shelby chat interface at the bottom, left corner of every screen. Every question that you
ask helps train the appliance to understand your needs, even when the appliance does not know the answer today.
Download the Security Certificate
1. From the Explorer tab of the appliance web services, click the Control Panel ( ) and the System tab.
2. Click Download SSL Certificate and follow the prompts to save the file on your computer.
Additional Settings
From the Explorer tab of the appliance web services, select the Control Panel ( ) to change configuration settings.
Yo u ca n :
• Restart or shut down the appliance.
• Reset the appliance to factory settings.
• Select specific devices or ranges of devices for the appliance to monitor.
• Define network access for ETH1 and ETH2 ports.
• Initiate an update for the appliance.
IMPORTANT To avoid problems with the appliance, click the Shutdown Appliance button on the Control Panel to turn off the
appliance. Do not disconnect power.
Allen-Bradley, Rockwell Software, Rockwell Automation, LISTEN. THINK. SOLVE, FactoryTalk, CompactLogix, ControlLogix, E300, and PowerFlex are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 6200-QS001C-EN-P - May 2018 PN-423354 / DIR 10003000325_02
Supersedes 6200-QS001B-EN-P- December 2017 Copyright © 2018 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Rockwell Automation Support
Use the following resources to access support information.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the
How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Technical Support Center
Knowledgebase Articles, How-to Videos, FAQs, Chat,
User Forums, and Product Notification Updates.
www.rockwellautomation.com/knowledgebase
Local Technical Support Phone Numbers Locate the phone number for your country.
www.rockwellautomation.com/global/support/get-support-no
w.page
Direct Dial Codes
Find the Direct Dial Code for your product. Use the
code to route your call directly to a technical support
engineer.
www.rockwellautomation.com/global/support/direct-dial.pag
e
Literature Library
Installation Instructions, Manuals, Brochures, and
Technical Data.
www.rockwellautomation.com/literature
Product Compatibility and Download Center
(PCDC)
Get help determining how products interact, check
features and capabilities, and find associated
firmware.
www.rockwellautomation.com/global/support/pcdc.page
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-com
Thank You
Welcome to FactoryTalk Analytics for Devices (we call it ‘Shelby’). We’re glad you’re here. This product is new, and
is improving regularly, but we hope you find Shelby useful from the moment you plug it in. Shelby offers many new
things: a new way to view industrial data, a new way to make products, and a new way to enhance products over
time.
Shelby gets better and smarter over time, as we learn from you how to improve. The sync process is where we get data
about how Shelby is working and being used. In exchange, you get the latest and greatest features, analytics, and
actionable information. Whether your Shelby works online or offline, we’ve made a way for it to continue working
better. We also want to hear from you! If you have information or feedback, email us at:
ftanalytics@ra.rockwell.com
So, a big thank you from the team, for investing with us as we make industrial data easier to use and understand. This
is only the beginning, and we’re excited for what’s still to come!
To order Shelby, go to http://commerce.rockwellautomation.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Allen-Bradley FactoryTalk Analytics for Devices Quick start guide

Allen-Bradley
Brand
Allen-Bradley
Model
FactoryTalk Analytics for Devices
Category
Networking
Type
Quick start guide

Allen-Bradley FactoryTalk Analytics for Devices is an analytical appliance that monitors the status of control devices on an EtherNet/IP network. It can detect EtherNet/IP devices automatically, analyze device data for display on device-specific dashboards, and perform system-level health and diagnostics.

The appliance is easy to set up and use. Simply connect it to your network and power it on. The appliance will automatically detect EtherNet/IP devices on the network and begin collecting data. You can then access the appliance's web interface to view data and configure settings.

FactoryTalk Analytics for Devices can help you to improve the performance and reliability of your control system. By monitoring the status of your devices, the appliance can identify potential problems before they cause downtime. The appliance can also provide you with insights into how your devices are performing, so that you can make informed decisions about how to improve their efficiency.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents