Chuango DWC-102 User manual

DWC-102
Chuango
Brand
Chuango
Model
DWC-102
Type
User manual

This manual is also suitable for

Chuango DWC-102 is a wireless door/window contact that alerts you when a door or window is opened. It features low battery and tamper alerts, and an external input for wired accessories. Easy to install with double-sided tape or screws, it operates on two AAA batteries and has a transmitting distance of up to 80 meters in an open area.

Chuango DWC-102 is a wireless door/window contact that alerts you when a door or window is opened. It features low battery and tamper alerts, and an external input for wired accessories. Easy to install with double-sided tape or screws, it operates on two AAA batteries and has a transmitting distance of up to 80 meters in an open area.

DWC-102
User Manual
Wireless Door/Window
Contact
PCB Layout
Tamper switch
Zone setup
Installation & Notice
Open the case and remove the battery activation strip.
Mount the sensor on the door frame and the magnet on the door.
Make sure the magnet is on the right side of the transmitter
Place the transmitter in the desired location, mount the
magnet no more than 1cm away from the transmitter and secure
the transmitter and magnet with double-sided tapes or screws.
Avoid mounting sensors in areas with a large quantity of metal
or electrical wiring, such as a furnace or utility room.
The DWC-102 is a Door/Window Contact that can be installed on
doors, windows, and any other objects that open and close.
The sensor transmits signals to the control panel when a magnet
mounted near the sensor is moved away. It will also transmit alert
signal to the control panel in case of low battery.
External input for wired accessory is available at the N/C interface.
The tamper protection ensures that sabotage attempts to move
the contact will result in an alarm activation.
Introduction
Product Overview
Transmitter Magnet
LED indicator
Specifications
0°C~+50°C
107 x 54
x 14.5mm
49 x 19.4 x 9.6mm
DC 3V (AAA 1.5V LR03 Battery x 2 pc)
433.92MHz
≤ 23uA ≤ 40mA
Power supply
Static current Alarm current
Transmitting distance
Radio frequency
Housing material ABS plastic
Operating temperature
Transmitter dimensions (LxWxH)
Magnet dimensions (LxWxH)
Relative humidity ≤80% (non-condensing)
≤80m (in open area)
AA 1.5V LR6
LED Indication
LED flashes once: Door/window is opened and transmitter sends
signal to the control panel.
Flash once per 3 seconds: Low power indication, please change
battery as soon as possible. (User will get alert SMS about the low
battery if the door contact is connected to the GSM alarm system.)
Ver: DWC-102-EN-1405-V5.0
2014 Chuango. All rights reserved.
NOTE: Tamper will be triggered no matter the door/window contact
is armed or disarmed.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment..
  • Page 1 1

Chuango DWC-102 User manual

DWC-102
Chuango
Brand
Chuango
Model
DWC-102
Type
User manual
This manual is also suitable for

Chuango DWC-102 is a wireless door/window contact that alerts you when a door or window is opened. It features low battery and tamper alerts, and an external input for wired accessories. Easy to install with double-sided tape or screws, it operates on two AAA batteries and has a transmitting distance of up to 80 meters in an open area.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents