Dometic SZ LCD Thermostat Operating instructions

Dometic
Brand
Dometic
Model
SZ LCD Thermostat
Type
Operating instructions

This manual is also suitable for

Dometic 3313325.031 SZ LCD Thermostat offers precise temperature control for your home's heating and cooling systems. With its user-friendly interface, you can effortlessly switch between fan, cool, and furnace modes to maintain your desired comfort level. The auto fan feature optimizes airflow, while the programmable temperature set-points allow for energy-efficient operation. Additionally, the thermostat displays error codes for easy troubleshooting, ensuring efficient system performance.

Dometic 3313325.031 SZ LCD Thermostat offers precise temperature control for your home's heating and cooling systems. With its user-friendly interface, you can effortlessly switch between fan, cool, and furnace modes to maintain your desired comfort level. The auto fan feature optimizes airflow, while the programmable temperature set-points allow for energy-efficient operation. Additionally, the thermostat displays error codes for easy troubleshooting, ensuring efficient system performance.

Single Zone LCD Thermostat
User’s Guide
Error Code:
E1 Loss of communication between the Single Zone LCD
thermostat and module board. LCD will cycle between E1
and previous mode setting. System will shut down.
E2 Open circuit or out of range Indoor Temperature Sensor.
Heating and cooling operation will be locked out. Fan op-
eration can continue to operate.
E3 Shorted Indoor Temperature Sensor. Heating and cooling
operation will be locked out. Fan operation can continue
to operate.
E4 Open circuit or out of range Outdoor Temperature Sensor
(Select Models). Heat pump will be locked out. Air condi-
tioner, furnace, and fan mode of operation can continue
to operate.
E5 Open circuit or out of range Freeze Sensor. Air condi-
tioner mode of operation will be locked out. Furnace, heat
strip, heat pump, and fan mode of operation can continue
to operate but displays the last temperature set-point.
REVISION_A
Form No. 3313325.031 08/16
(French 3313326.039_A)
©2016 Dometic Corporation
LaGrange, IN 46761
USA
SERVICE OFFICE
Dometic Corporation
1120 North Main Street
Elkhart, IN 46514
CANADA
Dometic Corporation
46 Zatonski, Unit 3
Brantford, ON N3T 5L8
CANADA
For Service Center
& Dealer Locations:
Please visit: www.eDometic.com
Special Features:
• Auto Fan
See Operating Instructions for more
Information on this special feature.
LCD Error Code
When the system determines that one
of the faults listed below has occurred
an error code will be displayed in the
LCD.
In the unlikely event you experience a
system failure, refer to the “SERVICE”
section of the Operating Instructions
furnished with your unit.
Dometic Single Zone LCD Thermostat Quick Start-Up
The basic steps for operating your Air Conditioner or Heat Pump are described in
this User’s Guide. For more detailed information on modes of operation and special
features refer to the Operating Instructions Manual.
Quick reference to control buttons
Press to decrease
temperature set-point
Press to increase
temperature set-point
Indicates mode of operation
when illuminated
* Select models
Press to select
mode of operation
On/Off
Mode
Fan
Cool
Furnace
*Heat
Pump or
Heat Strip
˚F
Fan Mode Setting
1. Press and release the On/Off Mode button. Press and
release the “+” or “―” button to cycle through the fan
speed options (Lo (Low), Hi (High), Au (Auto)).
On/Off
Mode
Fan
Cool
Furnace
Mode of Operation
A mode is an operation that can be performed by the
Dometic Single Zone LCD Thermostat.
2. Press and release the On/Off Mode button to cycle
through the available modes. All Dometic Single Zone
LCD Thermostats have Cool and Furnace modes. Select
models will have an additional mode, either Heat Pump
or Heat Strip. When desired mode has been selected, the
LCD will display the temperature set-point and the green
LED will be lit next to the selected mode.
To change the set-point, press the “+” button to increase
the set point and the “―” button to decrease the set-point.
On/Off
Mode
Fan
Cool
Furnace
˚F
On/Off
Mode
Fan
Cool
Furnace
˚F
Inside Temperature
3. To display the Inside Temperature, the Single Zone LCD
thermostat must be in the OFF Mode. Press either the “+”
or “―” button to display the Inside Temperature.
  • Page 1 1

Dometic SZ LCD Thermostat Operating instructions

Dometic
Brand
Dometic
Model
SZ LCD Thermostat
Type
Operating instructions
This manual is also suitable for

Dometic 3313325.031 SZ LCD Thermostat offers precise temperature control for your home's heating and cooling systems. With its user-friendly interface, you can effortlessly switch between fan, cool, and furnace modes to maintain your desired comfort level. The auto fan feature optimizes airflow, while the programmable temperature set-points allow for energy-efficient operation. Additionally, the thermostat displays error codes for easy troubleshooting, ensuring efficient system performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents