Mace XCi Card Quick start guide

Mace
Brand
Mace
Model
XCi Card
Type
Quick start guide

Mace XCi Card

The Mace XCi Card is a powerful and versatile device that can be used to monitor and control a wide range of water-related parameters. It is ideal for use in a variety of applications, including water treatment plants, wastewater treatment plants, and industrial facilities.

The XCi Card is easy to install and use. It can be connected to a PC using FloCom+ software, which provides a user-friendly interface for configuring the card and viewing data. The card can also be used with a variety of other software applications, including SCADA systems and data loggers.

The XCi Card is a cost-effective way to improve the efficiency and reliability of your water treatment system. It can help you to:

Mace XCi Card

The Mace XCi Card is a powerful and versatile device that can be used to monitor and control a wide range of water-related parameters. It is ideal for use in a variety of applications, including water treatment plants, wastewater treatment plants, and industrial facilities.

The XCi Card is easy to install and use. It can be connected to a PC using FloCom+ software, which provides a user-friendly interface for configuring the card and viewing data. The card can also be used with a variety of other software applications, including SCADA systems and data loggers.

The XCi Card is a cost-effective way to improve the efficiency and reliability of your water treatment system. It can help you to:

1. Register for a User Login at www.macemeters.com
2. Download FloCom
+
software and the XCi device product manual. These will be
needed to complete the card installation procedure.
3. If you are installing this card into a new XCi device proceed to Step 4. However if you
are installing this card into a device which is already in use, then users are advised to
“Download” data and “Stop” the device in FloCom
+
prior to installing additional cards.
4. Open the XCi device enclosure and ground yourself by touching the screw labelled
“Ground yourself here” on the LCD circuit board.
11. From the main menu of FloCom
+
, click “System” then “Module check” and ensure
that your newly installed card/s are listed and in the correct card slots.
10. “Connect” to the XCi device with a PC using FloCom
+
as detailed in the XCi device
product manual.
10
12. If they are not listed and/or not in the correct slot, “Disconnect” from the XCi device
in FloCom
+
.
13. REMOVE the oending card/s and WAIT for at least one minute. This allows the
microprocessor on the card to reset. Follow steps 4-12 for re-installation.
WARNING: Before removing the card/s you MUST re-ground yourself by
following the procedure outlined in step 4.
4
www.macemeters.com
mace water monitoring solutions
Installation Guide:
FloSeries3
Cards
Part No. 825-325 Revision 1.1
MACE USA LLC
PO Box 7144. Overland Park,
KS 66207, USA
Ph: 888 440 4215 Fax: 888 440 6999
Email: [email protected]
www.maceusa.com
Measuring & Control Equipment (MACE) Pty Ltd
PO Box 911, Pennant Hills,
NSW 1715, Australia
Ph: +61 (0)2 9658 1234 Fax: +61 (0)2 9651 7989
Email: [email protected]
www.macemeters.com
Part No. 825-325 Rev. 1.1
7. Remove the FloSeries3 card from its packaging. Position the new card in your hand
such that the large cream 48-pin connector is facing down and aligned with the mating
connector on the backplane PCB.
5. Remove the three screws (using a #2 Phillips screwdriver) fastening the PCB clamping
bracket. Take care not to drop screws in the box as damage may occur to the circuitry.
6. Ground yourself again as per instructions in step 4.
5
7
8
9
8. Ground yourself again. Your nger must remain grounded on the screw whilst
carefully inserting the card into any spare slot.
NOTE: If installing a WebComm card then you MUST use card slot 5.
Take care to align the pins of the two connectors together. There is a slot at the top
of the card area that helps the alignment process. Ensure that the card is contained
within this slot and press down rmly to ensure that it is fully seated.
9. Replace the PCB clamping bracket ensuring that the slots in the underside of the
bracket are aligned with the tops of all the cards. Fix the bracket into place with the
three screws. DO NOT over tighten the screws.
INSTALLATION GUIDE: FLOSERIES3 CARDS PAGE 2 PAGE 3 MACE WATER MONITORING SOLUTIONS
  • Page 1 1
  • Page 2 2

Mace XCi Card Quick start guide

Mace
Brand
Mace
Model
XCi Card
Type
Quick start guide

Mace XCi Card

The Mace XCi Card is a powerful and versatile device that can be used to monitor and control a wide range of water-related parameters. It is ideal for use in a variety of applications, including water treatment plants, wastewater treatment plants, and industrial facilities.

The XCi Card is easy to install and use. It can be connected to a PC using FloCom+ software, which provides a user-friendly interface for configuring the card and viewing data. The card can also be used with a variety of other software applications, including SCADA systems and data loggers.

The XCi Card is a cost-effective way to improve the efficiency and reliability of your water treatment system. It can help you to:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents