SignaMax SF-Series Pre-Polished Fiber Optic Connectors Installation guide

Brand
SignaMax
Model
SF-Series Pre-Polished Fiber Optic Connectors
Type
Installation guide
Field-Installable Pre-Polished Optical Fiber Connectors
www.signamax.com
999 N.W. 159
th
Drive
Miami, FL 33169
800.446.2377
305.944.7710
Fax: 305.949.4483
Copyright 2007 Signamax/AESP, Inc. All rights reserved
Signamax Connectivity Systems is a trademark of AESP, Inc.
Specifications subject to change
Connectivity Solutions
INSTALLATION INSTRUCTIONS
FPC
-
02 Rev.A JAN
-
2016
1
The following installation instructions are intended to be
used when installing the following Signamax optical
Connectors:
FPCxx-SCxx-02
FPCxx-LCxx-02
NOTES:
1. Optical fiber connectors shown in these instructions used for
example purpose only; actual product maybe slightly different in
dimensions and design detail.
2. Picture of tool used for example purpose only; actual tools may
differ from those shown.
3. All illustrations are not to scale
Make sure you have all necessary
tools for the job:
• Cable jacket stripping tool
• Optical fiber stripping tool
• Optical fiber cleaving tool
• Lint-free cloth wipes
• Optical fiber cleaning fluid
• Metric ruler and marker pen
WARNING:
• Wear safety glasses before handling
optical fiber to protect the eyes.
• Never look into the end of a connector or
an optical fiber which may have a laser
coupled to it.
Identify components of the connectors kits:
1: Fiber Connector 2: 900-µm Boot 3: 250-µm Tube
!
3
1
2
Be sure there is no space between
the wedge and connector, if there is,
push the wedge and connector
together to realign.
3
Place the 900-µm boot on the fiber cable, if applicable
then slide 250-µm tube on the fiber. Angle cut first.
Strip 35 mm of 900- and 250-µm
coating off.
2
4
Clean the fiber with a lint-free wipe and
fiber preparation fluid.
5
Strip 35 mm of 250-µm coating off.
Field-Installable Pre-Polished Optical Fiber Connectors
www.signamax.com
999 N.W. 159
th
Drive
Miami, FL 33169
800.446.2377
305.944.7710
Fax: 305.949.4483
Copyright 2007 Signamax/AESP, Inc. All rights reserved
Signamax Connectivity Systems is a trademark of AESP, Inc.
Specifications subject to change
Connectivity Solutions
INSTALLATION INSTRUCTIONS
FPC
-
02 Rev.A JAN
-
2016
Insert the fiber into the connector.
Create a slight bend in the connector
to maintain connection.
2
2
Push the sides tabs to release
and remove the wedge.
2
Slide the boot onto the connector
body.
1
1
Unlock the lever by push out,
being careful not to press the side
tabs
Verify good termination by using a visible
light source.
Good Connection: Bad Connection:
No Light Visible Light
7
By re-inserting the wedge into
the connector, fiber connector
could be re-terminated.
!
8
9
10
Termination of the fiber connector is
complete.
11
12
Set the fiber on the Cleaver and cleave
the fiber to 10.5 mm.
6
  • Page 1 1
  • Page 2 2

SignaMax SF-Series Pre-Polished Fiber Optic Connectors Installation guide

Brand
SignaMax
Model
SF-Series Pre-Polished Fiber Optic Connectors
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents