Savant FTK-F2000-01 User guide

Brand: Savant

Model: FTK-F2000-01

Type: User guide

This manual is also suitable for

FTK-FTEST-00

ImportantCleaverNotes

SAVANT www.savant.com Page1of2

45PerserveranceWay,Hyannis,MA02601

ThecleaverinthisSavantSSF™terminationkitcomespre ‐adjustedtocleavetheSSF™Stronger,

Safer,andFasterfiberopticglassanditsintegralpolymericcoating.SSF™fibersaresignificantly

moredurablethanandhave10,000xthebendofstandardfiber,soadjustmentisnecessarytoallow

thiscleaverand

otherindustrystandardcleaverstosuccessfullycleaveSSF™fibers.



Thisadjustment,calleda“BladeHeightAdjustment”involvesraisingtheblade/wheelinthecleaver

upveryslightlysoitcan“score”theoutercoveringoftheglassfibercorrectlywhilethefiberis

tensionedacrosstwopads.Thisprovidesaclean“break”oftheglassfiberandallowsmaximum

signaltransfer.

Theadjustmentisdetailedintheinstructionsincludedwithyourcleaver.Wheel

heightisraisedinveryfineincrementsuntilasuccessfulcleaveisachieved.Ifforanyreasonan

adjustmentisnecessaryinthefield,pleaserefertotheincludedinstructional.Thewheelheight

adjustmenttakes5to10

minutestoperform.



Yournewcleaverhasbeenfactory‐adjustedandverifiedbymicroscopetoensuresuccessful90‐

degreeendfacecleavespriortoshipping.





Frequently Asked Questions:

In which “slot” do I position the fiber?

A:Thecleaverisconfiguredtoaccept250um,900um,2mm,and3mmjacketedfibers.Sinceyouwill

typicallybeworkingwith250um(diameterofacrylatesoftpeelcoloredcoating),youmayuseeitherslot

dependingonhowthejacketedfibercanbepositionedonthetray.Usetheslotthat

allowsyouto

positionthefibermosteffectively:laidstraight/ata90‐degreeanglewiththecleaverwheel.Typicallyslots

canaccommodateallfibertypes.Positioningisimportantinobtainingqualitycleaves/endfacesonthe

fiberopticcableyouareworkingwith.

How do I prep the fiber?

A:Makesuretoremoveallofthesoftpeelcoatingfromthedeterminedpointontheopticalcabletothe

endperyourconnectorinstructional’scleavemeasurement.Ensurethesoftpeeliscompletelyremoved

byrunningyourfingersonallsidesoftheglass.Ifdesiredafiberwipe

maybeutilized.However,itisnot

necessaryastheopticalglassiscoated/protected.Neverattempttocleavethefiberwiththesoftpeel

coatingstillontheglass,asthiswill“dirty”thecleavingwheel.Ifthisoccurs,cleanwithacottonswab

soakedinalcohol.



My cleaver is not working/will not cleave the glass fiber – solution?

A:Afterpositioningthefiber,useyourthumbtopushthecleaverslidelever(locatedlowerrightonthe

cleaver).Sometimesdoingthistooslowlywillcausethefibertonotcleave.Givetheslideleveragood

push.Youarenottryingto“snapit;”justuseasteady

push.Withjustabitofpractice,thefibershould

successfullycleave.Alsomakesureyouareclosingthe“lid/handle”ofthecleavercompletely.Thefiber

additionallyneedstoextendouttherightside,beingplacedoverbothblackpadsandplacedoverthe

trashcollectorsothatoncecleaved,the

wasteglasscanbecaughtinthesmalltrashbin.

Savant FTK-F2000-01 User guide

Brand: Savant

Model: FTK-F2000-01

Type: User guide

This manual is also suitable for

FTK-FTEST-00

Download PDF

report

Savant FTK-F2000-01 User guide

This manual is also suitable for

Savant FTK-F2000-01 User guide

Related papers

Other documents