MicroNet SP3362A User manual

Micronet

R

Faster and Easier Networks

User’s Manual

ADSL2+ Router

Model No. SP3362A

http://www.micronet.info

1

CE Declaration of conformity

This equipment complies with the requirements relating to electromagnetic

compatibility, EN55022 class A for ITE, the essential protection

requirement of Council Directive 89/336/EEC on the approximation of the

laws of the Member States relating to electromagnetic compatibility.

FCC Part 68

This equipment complies with Part 68 of the FCC Rules. On the bottom of

this equipment is a label that contains the FCC Registration Number and

Ringer Equivalence Number (REN) for this equipment. You must provide

this information to the telephone company upon request.

The REN is useful when determining the quantity of devices you may

connect to the telephone line and still have all of those devices ring when

your number is called. In most, but not all areas, the sum of the REN of all

devices connected to one line should not exceed five (5.0). To be certain of

the number of devices you may connect to your line, as determined by the

REN, you should contact your local telephone company to determine the

maximum REN for your calling area.

If the modem causes harm to the telephone network, the telephone

company may discontinue your service temporarily. When possible, they

will notify you in advance. But if advance notice isn't realistic, you will be

notified as soon as possible. You will be advised of your right to file a

2

complaint with the FCC.

The telephone company may make changes in its facilities, equipment,

operations, or procedures that could affect the proper operation of your

equipment. If they do, you will be notified in advance to give you an

opportunity to maintain uninterrupted telephone service.

If you experience trouble with this modem, please contact your dealer for

repair/warranty information. The telephone company may ask you to

disconnect this equipment from the network until the problem has been

corrected or you are sure that the equipment is not malfunctioning.

This equipment may not be used on coin service provided by the

telephone company. Connection to party lines is subject to state tariffs.

Installation

This device is equipped with a USOC RJ11C connector.

FCC Part 15

The modem generates and uses radio frequency energy. If it is not

installed and used properly in strict accordance with the user's manual, it

may cause interference with radio and television reception. The modem

has been tested and found to comply with the limits for Class B computing

devices in accordance with the specifications in Subpart B, Part 15 of the

FCC regulations. These specifications are designed to provide reasonable

protection against such interference in a residential installation. However,

3

there is no guarantee that interference will not occur in a particular

installation. FCC regulations require that shielded interface cables be used

with your modem.

If interference does occur, we suggest the following measures be taken to

rectify the problem:

1) Move the receiving antenna.

2) Move the modem away from the radio or TV.

3) Plug the modem into a different electrical outlet.

4) Discuss the problem with a qualified radio / TV technician.

CAUTION:

Changes or modifications not expressly approved by the party responsible

for compliance to the FCC Rules could void the user's authority to operate

this equipment.

Cable connections:

All equipment connected to this modem must use shielded cable as the

interconnection means.

Notes:

Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including

interference that may cause undesired operation.

4

Contents

CE Declaration of conformity......................................................................1

Chapter 1 Introduction..............................................................................7

1.1 Overview........................................................................................7

1.2 Features ........................................................................................8

1.3 System Requirements.................................................................10

Chapter 2 Installation.............................................................................11

2.1 Checklist......................................................................................11

2.2 The Front LEDs ...........................................................................12

2.3 The Rear Ports ............................................................................13

2.4 Hardware installation...................................................................14

2.5 Splitter Configuration...................................................................15

Chapter 3 Connection............................................................................18

3.1 Setup router via Ethernet Cable..................................................18

3.2 Determine connection settings....................................................31

3.3 Connecting the Router to network...............................................31

3.4 The relative configuration on PC.................................................32

Chapter 4 Configuration..........................................................................40

4.1 Login.............................................................................................40

4.2 Quick Start....................................................................................42

4.3

Interface Setup............................................................................44

4.3.1 Internet..............................................................................44

4.3.2

LAN ................................................................................51

5

4.4 Advanced Setup...........................................................................54

4.4.1 Firewall.............................................................................54

4.4.2 Routing.............................................................................54

4.4.3 NAT .................................................................................56

4.4.4 QoS ...............................................................................61

4.4.5 VLAN................................................................................63

4.4.6 ADSL ................................................................................65

4.5 Access Management....................................................................67

4.5.1 ACL ..................................................................................67

4.5.2

IP Filter.............................................................................69

4.5.3

SNMP...............................................................................74

4.5.4

UPnP................................................................................74

4.5.5

DDNS................................................................................76

4.5.6

CWMP...............................................................................77

4.6 Maintenance.................................................................................79

4.6.1 Administration...................................................................79

4.6.2

Time Zone........................................................................79

4.6.3

Firmware...........................................................................81

4.6.4

System Restart.................................................................82

4.6.5

Diagnostic.........................................................................83

4.7

Status............................................................................................84

4.7.1

Device Info........................................................................84

4.7.2

System Log.......................................................................87

4.7.3

Statistics...........................................................................88

Chapter 5 Troubleshooting......................................................................89

5.1 Using LEDs to Diagnose Problems..............................................89

6

5.1.1 Power LED.......................................................................89

5.1.2 LAN LED..........................................................................90

5.1.3 ADSL LED........................................................................90

5.2 Problems with the Web Interface.................................................91

5.3 Problems with the Login Username and Password.....................92

5.4 Problems with LAN Interface.......................................................92

5.5 Problems with WAN Interface......................................................93

5.6 Problems with the Internet Access...............................................94

Appendix A Glossary...............................................................................96

Appendix B Cabling...............................................................................103

Appendix C Service / Port.....................................................................104

7

Chapter 1 Introduction

The ADSL2+ Modem Router provides home connectivity to an ADSL service

provider network over an ADSL/ Asynchronous Transfer Mode (ATM)

physical layer. The router can run upstream maximum transmission rates

of 2Mbps and downstream maximum transmission rates of 24Mbps. The

actual rate depends on the copper category of your telephone wire,

distance from the central office and the type of ADSL2+ service

subscribed. One Ethernet port is provided for connection to an Ethernet

LAN or Ethernet-equipped PC and this router is easy to install and to

configure.

1.1 Overview

This router is optimized to address the growing demand for

high-speed Internet access, and it does so as a single, highly-integrated

and cost-effective solution. This router provides RJ-45 Ethernet port

for network connection.

8

1.2 Features

ADSL2/2+ Compliance

♦ Compliant with ADSL standards

Full-rate ANSI.413 Issue 2 , ITU G.dmt (G.992.1) , G.dmt bis (G.992.3)

and G.adslplus(G.992.5) standards

Splitter less ITU G.lite (G.992.2) specification

Annex A (ADSL over POTS) and Annex B (ADSL over ISDN), compliant

to ETSI TS 101 388

♦ DMT modulation and demodulation

♦ Full-rate adaptive modem

Maximum downstream rate of 24 Mbps

Maximum upstream rate of 2 Mbps

♦ Tone detection for low power mode

♦ Supports splitter less ADSL implementation

♦ Interoperable with all major DSLAM equipment

ATM Protocols

♦ WAN mode support: PPP over ATM (RFC 2364) and PPP over Ethernet

(RFC 2516)

♦ LAN mode support: bridged/routed Ethernet over ATM (RFC 2684) and

classical IP over ATM (RFC 1577)

♦ Up to 8 VCs (virtual circuits)

♦ ATM SAR (segmentation and reassembly)

♦ ATM AALC (adaptation layer type 5)

9

Bridge Mode

♦ Ethernet to ADSL self learning Transparent Bridging (IEEE 802.1D)

♦ Supports MAC learning addresses

Router Mode

♦ IP routing-RIPv2

♦ Static routing

♦ DNS Proxy

♦ Dynamic DNS

♦ DMZ

♦ Port Forwarding

♦ DHCP (dynamic host configuration protocol) server and client

♦ NAT (network address translation)

♦ ICMP (Internet control message protocol)

Security

♦ Stateful packet inspection and filtering

♦ Intrusion detection and protection

♦ PAP (password authentication protocol)

♦ CHAP (challenge authentication protocol)

♦ Password protected system management

Ethernet Interface

♦ Compliant with IEEE 802.3 and 802.3u 10/100 Mbps

10

HTTP Web-Based Management

♦ Firmware upgrade by UI

♦ WAN and LAN side connection statistics

♦ Configuration of static routes and routing table

♦ Password protected access

♦ System log

♦ Configuration of VCs (virtual circuits)

1.3 System Requirements

♦ Pentium III 266 MHz processor or higher

♦ 128 MB RAM minimum

♦ 20 MB of free disk space minimum

♦ RJ45 Ethernet Port

♦ CD-ROM drive

11

Chapter 2 Installation

This chapter offers information on how to install your router. If you are

not familiar with the hardware or software parameters presented here,

please consult your service provider for the values required.

2.1 Checklist

Check the box contents carefully to ensure that all items are included.

If any of the items are missing or damaged, contact your local distributor.

Contents description

♦ ADSL2+ Modem Router

♦ Quick Installation Guide

♦ User manual CD

♦ Power adapter

♦ RJ-11 telephone cable

♦ RJ-45 Ethernet cable

12

2.2 The Front LEDs

LED Description

ADSL

When connection with Internet (ADSL Connected) is

established, this LED will light up.

When this LED is flashing: NO ADSL physical connection

DATA

When router is transferring data between Internet and router,

this LED will be flashing.

LAN

When connection 10/100MB with end user is established, this

LED will light up. When router is transferring data between

router and end user, this LED will be flashing.

PWR

When an active power adapter is connected with router, this

LED will light up.

13

2.3 The Rear Ports

Connector Description

LINE Connect with telephone line.

Reset Reset button.

LAN

Connect with Ethernet Cable to Switch Hub or

PC

POWER Connect with power adapter

ON/OFF Power switch button

14

2.4 Hardware installation

This section describes how to connect and configure the ADSL router.

1) Connect the ADSL line

Connect the router directly to the wall jack using the included ADSL

RJ-11 telephone cable.

2) Connect a workstation to the Router's LAN port

Use Ethernet RJ-45 cable to connect computer or expend Ethernet

network.

3) Connect the power adapter to the Router

Connect the power adapter to the port labeled POWER on the rear

panel of router.

4) Connect all cables to the Network

The procedure for connecting cables differs depending on whether or

not your telephone equipment is connected to a POTS splitter. The next

section explains ADSL splitter and describes the configuration in

networks of ADSL over POTS and ADSL over ISDN.

15

2.5 Splitter Configuration

ADSL splitter builds-on a micro-filter it stops the ADSL signal

interfering with the voice part of your phone line. The graph hereunder

shows the frequency range that your phone (POTS) and ADSL occupy.

Use ADSL splitter to separate the bands for POTS and ADSL and get

better communication quality.

POTS Splitter Configuration (ADSL over POTS)

A POTS splitter separates data signals from voice signals on your

telephone line. The POTS splitter works by running a separate data line

from the voice line, so that the ADSL router has a cable dedicated for data

transmission. Figure 2-5.1 and 2-5.2 shows how to connect all cables to

the Router.

16

Figure 2-5.1 Router connected through a POTS Splitter

Note: The POTS splitter may also be installed on the outside of the house

adjacent to the telephone network interface device (NID).

Figure 2-5.2 Router connected through several micro-filters

17

ISDN Splitter Configuration (ADSL over ISDN)

A ISDN splitter separates ADSL signals from ISDN signals on your ISDN

telephone line. The ISDN splitter works by running a separate ADSL line

from the ISDN line, so that the ADSL router has a cable dedicated for data

transmission. Figure 2-5.3 shows how to connect all cables to the Router.

Figure 2-5.3 Router Connected through an ISDN Splitter

Note: The ISDN splitter may also be installed on the outside of the house

adjacent to the telephone network interface device (NID).

18

Chapter 3 Connection

You can connect ADSL2+ modem router with PC through either Ethernet

cable cable. After connection is established, you can configure the

host PC to be a DHCP client. You have to repeat the same steps for every

host PC on your network if you use DHCP function on your router.

3.1 Setup router via Ethernet Cable

If there is an available LAN card present on your PC, you just simply

connect ADSL router and PC through the Ethernet cable. Once you

establish Internet connection, you could browse the Web through the

Ethernet cable.

19

3.2 Determine connection settings

Before configuring the router, you need to know the connection

information supplied by your ADSL service provider.

3.3 Connecting the Router to network

Unlike a simple hub or switch, the setup of the ADSL Router consists

of more than simply plugging everything together. Because the Router acts

as a DHCP server, you will have to set some values within the Router and

also configure your networked PCs to accept the IP Addresses the Router

chooses to assign to them. Generally, there are several different operating

modes for your applications. Your ISP will tell you which mode is

necessary for your system. The modes available are router, bridge,

PPPoE+NAT and PPPoA+NAT.

Page is loading ...

MicroNet SP3362A User manual

MicroNet SP3362A User manual

Related papers

Other documents