EZ-Load Thermal Printer
Owner’s Manual
Legal Notices
Disclaimer
Information in this document is subject to change without notice. Consult your Nanoptix Inc. sales
representative for information that is applicable and current. Nanoptix Inc. reserves the right to
improve products as new technology, components, software, and firmware become available.
No part of this document may be reproduced or transmitted in any form or by any means,
electronic or mechanical, for any purpose without the express written permission of Nanoptix Inc.
Copyright
Copyright 2003 by Nanoptix Inc.
Dieppe, New Brunswick Canada
All rights reserved
Printed in Canada
Confidential, Unpublished
Property of Nanoptix Inc.
Trademarks
Epson is registered trademark of Epson Corporation.
Windows is registered trademark of Microsoft Corporation.
Nanoptix is a trademark. Other trademarks and registered trademarks are the property of their
respective holders.
Federal Communications Commission (FCC)
Radio Frequency Interference Statement
Warning
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
Information to the User
This equipment must be installed and used in strict accordance with the manufacturer's
instructions. However, there is no guarantee that interference to radio communications will not
occur in a particular commercial installation. If this equipment does cause interference, which can
be determined by turning the equipment off and on, the user is encouraged to contact Nanoptix
Inc. immediately.
101049
Sept. 21, 2005
ii
EZ-Load Thermal Printer
Owner’s Manual
Nanoptix Inc. is not responsible for any radio or television interference caused by unauthorized
modification of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Nanoptix Inc. The correction of interferences caused by
such unauthorized modification, substitution or attachment will be the responsibility of the user.
In order to ensure compliance with the Product Safety, ICES, FCC and CE marking requirements,
you must use the power supply, power cord, and interface cable which were shipped with this
product or which meet the following parameters:
Power Supply
UL Listed power supply with standard 60Hz-50Hz, 100-240VAC input and 24VDC output
equipped with AC line filtering, over-current and short-circuit protection.
Use of this product with a power supply other than the Nanoptix Inc. power supply will require you
to test the power supply and Nanoptix Inc. printer for FCC and CE mark certification.
Communication Interface Cable
An approved Nanoptix interface cable must be used with this product. Using a cable other than
Nanoptix approved product will require that you test the cable with the Nanoptix Inc. printer and
your system for FCC and CE mark certification.
Power Cord
A UL listed, detachable power cord must be used. A power cord with Type SVT marking must be
used. For applications outside the North America, power cords that meet the particular country’s
certification and application requirements should be used.
Use of a power cord other than described here may result in a violation of safety certifications
that is in force in the country of use.
Industry Canada (IC)
Radio Frequency Interference Statement
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
101049
Sept. 21, 2005
iii
EZ-Load Thermal Printer
Owner’s Manual
Table of Contents
1. About the Printer........................................................................ 1
1.1 Description of Printer ...................................................................................1
1.2 General specifications..................................................................................2
1.3 Printer Controls.............................................................................................3
To reset Printer........................................................................................................................ 3
Paper Feed Button................................................................................................................... 4
1.4 Changing Paper ............................................................................................5
1.5 Testing the Printer........................................................................................8
1.6 Troubleshooting the Printer.........................................................................9
Printer LED .............................................................................................................................. 9
Printing Problems .................................................................................................................... 9
Printer Does Not Work........................................................................................................... 10
2. Media and Supplies Guide....................................................... 11
2.1 Thermal Paper Specifications....................................................................11
2.2 Ordering Thermal Paper.............................................................................11
2.3 Ordering Miscellaneous Supplies .............................................................12
Power Supply and Power Cord.............................................................................................. 12
Ordering Communication Cables........................................................................................... 12
Communication Cables Pin-Out ............................................................................................ 13
3. Communicating with the Printer............................................. 14
APPENDIX A: Mechanical Drawings............................................. 15
101049
Sept. 21, 2005
iv
EZ-Load Thermal Printer
Owner’s Manual
Figures
FIGURE 1: NANOPTIX EZ-LOAD PRINTER................................................................................................. 1
FIGURE 2: RESETTING PRINTER................................................................................................................ 3
FIGURE 3: PAPER FEED BUTTON .............................................................................................................. 4
FIGURE 4: LOADING PAPER ....................................................................................................................... 5
FIGURE 5: ALIGNING PAPER EDGE .......................................................................................................... 6
FIGURE 6: CLOSING DOOR......................................................................................................................... 6
FIGURE 7: TEST TICKET.............................................................................................................................. 8
FIGURE 8: MECHANICAL DIMENSIONS.....................................................................................................15
101049
Sept. 21, 2005
v
EZ-Load Thermal Printer
Owner’s Manual
Tables
TABLE 1: SPECIFICATION........................................................................................................................... 2
TABLE 2: TROUBLESHOOTING WITH THE STATUS LED......................................................................... 9
TABLE 3: TROUBLESHOOTING PRINTING PROBLEMS........................................................................... 9
TABLE 4: PRINTER DOES NOT WORK......................................................................................................10
TABLE 5: THERMAL PAPER DIMENSIONS ...............................................................................................11
TABLE 6: ORDERING THERMAL PAPER...................................................................................................11
TABLE 7: POWER SUPPLY AND POWER CORD PART NUMBERS ........................................................12
TABLE 8: COMMUNICATION CABLES PART NUMBERS.........................................................................12
TABLE 9: RS-232 INTERFACE PIN-OUT.....................................................................................................13
101049
Sept. 21, 2005
vi
EZ-Load Thermal Printer
Owner’s Manual
1. About the Printer
1.1 Description of Printer
The Nanoptix EZ-Load printer is extremely fast, quiet, and very reliable. With thermal
printing technology, there is no ribbon cassette to change, and paper loading is
extremely simple. The printer is small enough to fit almost anywhere and is easy to use
with the ticket exiting from the front.
Figure 1: Nanoptix EZ-Load Printer
101049
Sept. 21, 2005
1
EZ-Load Thermal Printer
Owner’s Manual
1.2 General specifications
Print Method Direct Thermal
Resolution 8 dot/mm (203 dpi)
Print Width 80mm
Paper Width 80mm or 82.5 mm
Max Roll Diameter 115mm
Operating Temperature 0 to 50 C
Storage Temperature -40 C to +65 C
Operating Relative Humidity 20% to 85% RH at 50C (non-condensing)
Communication Interface Options USB, RS-232C, RS-485, IEEE1284
Memory/Firmware 1 Mbit of SRAM, 4 Mbit of flash and 128kbit of
EEPROM
Resident Character Sets Arial Bold (6 sizes)
Note: Other Character sets can be
programmed quickly
Integrated Bar Codes UPC-A, UPC-E, interleaved 2 of 5, 3 of 9,
Code 128, EAN 8, EAN 13.
Note: Other Bar Codes can be programmed
quickly
Speed Up to 130 mm/second
Sensors • Paper out
• Door open
• Knife not homed
• Paper low
• Top of form (optional)
Human Interface Drop-in paper loading, status LED, paper feed
button
Dimensions 148mm width x 255mm height x 155mm depth
Weight 3.5 Kg
Immunity EN-55024
Emission Standards United States - FCC Part 15 Subpart B
Canada - Industry Canada ICES-003
Europe – EN 55022
Class A.
Table 1: Specification
101049
Sept. 21, 2005
2
EZ-Load Thermal Printer
Owner’s Manual
1.4 Changing Paper
Caution: Do not operate the printer if it runs out of paper. The printer will not operate
without paper, but it may continue to accept data from the host computer. Because the
printer cannot print any transactions, the data may be lost.
1. Open the front door.
2. Remove the used roll.
3. Tear off the end of the new roll so that the edge is loose and place the new roll into
the paper bucket with a few inches of loose paper.
Figure 4: Loading Paper
Caution: Be sure the paper unrolls from the top. Otherwise, the printer will not print or
the paper will jam.
101049
Sept. 21, 2005
5
EZ-Load Thermal Printer
Owner’s Manual
6. Advance the paper by pressing on the paper feed button and tear off the excess
paper.
Note: In the event of a paper jam, remove the roll, tear a new clean edge, and replace it
in the paper bucket, as described above. Be sure that the paper unrolls from the bottom
of the roll.
101049
Sept. 21, 2005
7
EZ-Load Thermal Printer
Owner’s Manual
1.5 Testing the Printer
Run this test to check the printer. The test prints and cuts a resident test ticket. Verify
this ticket to judge the printing quality.
Model: TITANIA
Firmware: TIT-2.41G-61UCS
COMMUNICATION
Interface: IEEE1284 (0) or Serial
Baud: 9600
Data Bits: 8
Parity: NONE
Handshaking: NONE
Print Mode: NTL
Aux Port: Disabled
PRINT CONTROL
Darkness Control: -1%
Voltage: 24.2 Volts
Temperature: 26 Celcius
Speed: 4 IPS
Black Bar Index: Disabled
SYSTEM RESOURCES
FLASH -Used: 0
-Free: 24576
LIBRARY INVENTORY
Templates: 0,1,2
Print Regions: 1,2,3,4,5,6,7,8,
h,9,A,B,C,D,E,F,G,
I,J,K,L,N,O,P,Q,R,
S,T,U,Z,X,a,b,c,d,
e,f,g,i,j,k,l,m,n,
o,p,q,
Graphics: None
Fonts: 0,3,5,7,8
MANUFACTURING INFORMATION
Printer ID: 5465789
Date Code: 20184
PWM Setting: 7F7F7F7FFFFFFF
A to D: DE7AA400FD000000
Resets: 9
Tickets: 00001336
Status: TIT-2.41G-40-40-40-40-40-P
Figure 7: Test Ticket
To print the test ticket, power-on the printer while pressing and holding the Paper Feed
Button for approximately 3 seconds. A test ticket similar to above will be printed
approximately 5 seconds after. Press the paper feed button once more and the ticket
will feed. Pressing the button again will result in blank tickets.
101049
Sept. 21, 2005
8
EZ-Load Thermal Printer
Owner’s Manual
1.6 Troubleshooting the Printer
The printer is simple and generally trouble-free, but from time to time minor problems
may occur. Follow these procedures to determine the cause and resolution of any
problems the printer may be having. If the procedures in this section do not correct the
problem, contact a service representative.
Printer LED
Condition LED Status
Unit ready ON
Unit is in Reset or Booting OFF
Unit in standby (powered off) OFF
Paper Out Slow Blink
Door Open Fast Blink
Paper Jam Fast Blink
Missing Black Index Mark Fast Blink
Temperature Error Med Blink
Voltage Error Med Blink
Print Head Error Med Blink
Table 2: Troubleshooting with the status LED
Printing Problems
Problem Possible Causes What to Do
Receipt does not come
out all the way. Paper is jammed. Open the receipt cover,
inspect the knife, and
clear any jammed paper.
Printer starts to print,
but stops while the
receipt is being printed.
Paper is jammed. Open the receipt cover,
inspect the knife, and
clear any jammed paper.
Paper is jammed.
Open the receipt cover,
inspect the knife, and
clear any jammed paper.
Receipt is not cut. The printer is not
configured for a knife. Contact your authorized
service representative.
Paper roll loaded
incorrectly. Check that the paper is
loaded properly.
Print is light or spotty. Thermal printhead is
dirty. Use recommended
thermal receipt paper.
Vertical column of print
is missing. This indicates a serious
problem with the printer
electronics.
Contact your authorized
service representative.
One side of receipt is
missing. This indicates a serious
problem with the printer
electronics.
Contact your authorized
service representative.
Table 3: Troubleshooting Printing Problems
101049
Sept. 21, 2005
9
EZ-Load Thermal Printer
Owner’s Manual
Printer Does Not Work
Problem Possible Causes What to Do
Check that printer cables
are properly connected
on both ends.
Printer not plugged in. Check that the host or
power supply is switched
on. Check Printer LED.
Printer Does Not
Function When Turned
On.
Door not fully
closed. Close the door.
Table 4: Printer Does Not Work
101049
Sept. 21, 2005
10
EZ-Load Thermal Printer
Owner’s Manual
2. Media and Supplies Guide
2.1 Thermal Paper Specifications
The printer requires qualified thermal paper with the following dimensions:
Width Diameter Outside Core Diameter
80 mm ± .2 mm (3.15 in. ± .008 in.) 115 mm max. (4.5 in.) 45mm (1.75 inches)
82.5 mm ± .2 mm (3.25 in. ± .008 in.) 115 mm max. (4.5 in.) 45mm (1.75 inches)
Table 5: Thermal Paper Dimensions
The paper should not be attached to the core. If Top of Form Option is installed, paper
with a colored stripe at the end can be used to indicate that the paper is running low.
2.2 Ordering Thermal Paper
We recommend the following paper grades produced by their respective manufacturers.
There are a number of paper converters qualified to supply this paper, provided the
thermal paper rolls are from these recommended grades.
Manufacturer Paper Grade Paper Thickness
Kanzaki Specialty Papers
(USA) Lotto 480 83 g/m2 – 3.3mil
Kanzan Spezialpapiere
GMBH (Germany) KLS 36
KLS 46 79g/m2 – 3.1mil
81g/m2 – 3.2mil
Appleton Papers, Inc.
(USA) Optima T-886 B (now Heatsafe 200-3.2) 82g/m2 – 3.2mil
Blumberg GMBH T49-32 88 g/m2 – 3.5mil
Mitsubishi TP8065 80g/m2 – 3.1mil
Table 6: Ordering Thermal Paper
Additional grades can be qualified and made available. Contact your sales
representative for more information.
101049
Sept. 21, 2005
11
EZ-Load Thermal Printer
Owner’s Manual
2.3 Ordering Miscellaneous Supplies
Power Supply and Power Cord
Contact your sales representative to order the power supply and power cords listed in
the table. The numbers are for reference only. Suppliers may use other numbers.
Part Part Number
Power Supply (24VDC, 2.5A max., 60W) 102048
Power Cord – North American 102080
Power Cord – Continental Europe 102086
Table 7: Power Supply and Power Cord Part Numbers
Ordering Communication Cables
Contact your sales representative to order the communication cables listed in the table.
The numbers are for reference only. Suppliers may use other numbers.
Part Part Number
Standard RS232 communication cable (Host Cable)
(DB9 male plug, DB9 female receptacle) 102082
Standard RS232 communication cable (Host Cable)
(DB9 female receptacle, DB25 male plug) 102106
Serial RS232 communication harness (Adapter Harness)
(DB9 male plug to DB25 female receptacle) 102042
Parallel communication cable (Host Cable)
(IEEE 1284 Type A to B - Large Centronics to DB25) 102083
USB communication cable (Host Cable)
(Type A to mini B) 102085
Table 8: Communication Cables Part Numbers
101049
Sept. 21, 2005
12
EZ-Load Thermal Printer
Owner’s Manual
Communication Cables Pin-Out
The tables below detail the connection pin-out for the RS-232 interface
(Female Receptacle DB-9).
Pin Signal Name Printer I/O Host I/O Printer
Function
1 n/a always driven low
(high on RS232
side)
Input None
2 PRT_RS232_TXD Output Input Data transmit
3 PRT_RS232_RXD Input Output Data receive
4 n/a No connect Output None
5 Signal Ground Signal Ground Signal Ground Signal
Ground
6 RS232_DSR Output Input Printer Ready
(Connected to
PRT_RS232_
RTS Pin 8)
7 PRT_RS232_CTS
(host RTS) Input Output Handshake
8 PRT_RS232_RTS
(host CTS) Output Input Handshake
9 n/a always driven high
(low on RS232
side)
Input None
Shell Frame Ground Frame Ground Frame Ground Shield
Table 9: RS-232 Interface Pin-Out
101049
Sept. 21, 2005
13
EZ-Load Thermal Printer
Owner’s Manual
3. Communicating with the Printer
Over the years, Nanoptix has developed emulations for compatibility with the most
popular printers in the market. At the time of printing this manual, the following
emulations are available:
i. Epson LQ570+
ii. Epson TM-T88III
iii. Star TUP-400
iv. Axiohm A722
v. Ithaca P70
vi. Ithaca P170
vii. Citizen 3551
Please contact your sales representative if you require other emulations. If we do not
have the emulation you need, we can provide most emulations in a short timeframe. If
you are not required to emulate other printer, please ask your sales representative for
the latest Nanoptix Windows Driver or the “Nanoptix Programming Guide” which will list
the Nanoptix ESC/P commands.
101049
Sept. 21, 2005
14
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Champion Power Equipment Model #100179 Installation guide
-
-
Champion 100199 Installation guide
-
CognitiveTPG A760 User manual
-
Wincor Nixdorf TH420 User guide
-
-
Axiohm A794-D100 User manual
-
-
TransAct Technologies ITHERM 280 User manual
-
Gtech Accutherm User manual
