Williams Sound Application Digi-wave™ Dock User guide

Brand: Williams Sound

Model: Application Digi-wave™ Dock

Type: User guide

Digi-Wave

™

Dock Application Guide

SYSTEM EXAMPLES

Digi-Wave Dock Application Guide

Table of Contents

Purpose of this Guide 3

Base Station Transmitter 4

Base Station Receiver 6

Teleconferencing 8

Range Extender 10

Interpretation with Wireless Presenter 12

Two-Way, Two-Language Question and Answer 14

5 Simultaneous Talkers with a 2.0 System 17

Extending a 2.0 Series system with 300 Series Product 20

Digi-Wave Dock Application Guide

Purpose of this Guide

The Digi-Wave Dock provides a way to:

(a) connect Digi-Wave wireless product to a hard-wired system,

(b) hard-wire wireless product together, and

This guide is designed to present various ways the Digi-Wave Dock can be utilized. The dock is a versatile piece of equipment, and the

following examples are by no means exhaustive. These examples are provided as a starting point for more creative or complex uses.

“DLT” in this guide refers to DLT 300 or DLT 100 2.0.

“DLR” in this guide refers to DLR 60, DLR 60 2.0 or DLR 360.

Note: The DLT 100 and DLR 50 units do not have active audio pins to send or receive audio through the 30-pin connector on the Dock. So

these units cannot be used in any of the scenarios described in this guide. The DLT 100 can be charged in the dock (only).

Cannot be used in any scenarios this guide:

DLT 100

DLR 50

Can be used in applicable scenarios in this guide:

DLT 300

DLT 100 2.0

DLR 360

DLR 60 2.0

DLR 60

Digi-Wave Dock Application Guide

Base Station Transmitter

The Digi-Wave Dock can be used as a method of transmitting audio from a sound system to the audience listening with transceivers or

receivers.

How it works:

An audio program, presenter’s voice, etc. is sent from a sound system or other equipment to the dock line input. The dock delivers the

audio to the docked transceiver which broadcasts the audio out to receivers (or transceivers) in the audience.

Required Equipment:

One Digi-Wave Dock, one DLT 300 Transceiver

Digi-Wave Dock Application Guide

Unit Programming for Base Station Transmitter

Unit

Location

Model Mode Priority Group Channel

Docked *

DLT 300

1-way - Main Speaker:

Master

01 0

Audience DLR 360 - - 01 0

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

Digi-Wave Dock

(rear)

A497

Docked

DLT

Analog

Line Output

(XLR or RCA)

Analog Line Input

(XLR or RCA)

An audio program, speakers voice, etc. is sent from a sound system or other equipment to the dock input. The dock delivers the audio to the docked

transceiver which broadcasts the audio out to receivers (or transceivers) in the audience.

Sound System,

Analog Mixer, etc.

Dock Bay Switch

set to “Auto”

DLT Programming:

Mode:

Priority:

Group: 01

Channel: 0

Talk Mode: PnL

Talk Button: ON

DLR Programming:

Group: 01

Channel: 0

Audience

Presenter

Digi-Wave Dock Application Guide

Base Station Receiver

The Digi-Wave Dock can be used to receive audio from a DLT, and send this audio into a sound system. Utilized in this way, a presenter

can be recorded, heard by the audience using receivers, or heard by the audience through loudspeakers.

How it works:

A presenter’s voice is transmitted from a DLT 300 transceiver to a docked DLR 360 receiver. The dock sends the audio through it’s line

outputs into a sound system or other equipment.

Required Equipment:

One Digi-Wave Dock, one DLR 360 Receiver

Digi-Wave Dock Application Guide

Base Station Receiver

Unit Programming

Unit

Location

Model Mode Priority Group Channel

Presenter

DLT 300

1-way - Main Speaker:

Master

01 0

Docked *

DLR 360 - -

01 0

*The docked DLR should have it’s bay switch set to “Auto”; this keeps it powered up and it will begin receiving when the dock

powers up and the Master is found.

The presenter’s DLT should be set to 1-way mode-Main Speaker/Master; this way when the presenter enters the room, the docked receiver

(or transceiver) will sync with the presenter’s DLT and begin receiving the audio, automatically.

Using a docked receiver is recommended for simplicity, but if using a docked DLT, it should be set to 2-way Slave mode. This will not work

if the docked DLT is in one-way mode.

Digi-Wave Dock (rear)

A496

Docked

DLR

Analog Line Input

(XLR or RCA)

Sound System

Analog Line Output

(XLR or RCA)

A speaker’s voice is transmitted from a DLT 100 2.0 to a docked DLR 60 2.0 receiver (or DLT 100 2.0

transceiver). The dock sends the audio through it’s outputs into a sound system or other equipment.

Presenter

Dock Bay Switch

set to “Auto”

The Audience hears the

Presenter through the

Sound System

3.5mm

HEADPHONE

DLR Programming:

Group: 01

Channel: 00

DLT Programming:

Mode:

Priority:

Group: 1

Channel: 0

Talk Mode: PnL

Talk Button: ON

Digi-Wave Dock Application Guide

Teleconferencing

The dock provides full duplex audio capability when a DLT Transceiver is docked. Utilized in this way, two-way communication can be

established between two conference rooms, with audio sent/received over the internet. People on both sides can speak/listen with DLT

transceivers, or just listen with DLR receivers. A program such as Skype or other teleconference software can be used to make the

conference call over the internet. The two-way audio from each dock is connected to the computer in that conference room, and the audio

from the dock is routed into a sound system in that room. Additional DLTs can be added for hearing assistance, asking and answering

questions, or for presentations where a person will be standing or walking.

How it works:

In Conference Room 1, people’s voices are picked up using the internal microphone* on a portable DLT on the conference room table.

This audio is transmitted to a docked DLT. The dock sends the audio through it’s outputs to a computer. The computer sends the audio

through the internet where it is received by a computer in Conference Room 2. The computer in Conference Room 2 sends its audio to a

sound system for people in Conference Room 2 to hear. Additional DLTs can be used for hearing assistance or Q&A.

In the same manner, audio is sent from Conference Room 2 to Conference Room 1. Typically this type of system is coupled with a video

screen in each conference room, so the people in both locations can see each other.

*a conference microphone could also be used for improved pickup of multiple voices (not shown)

Required Equipment:

Two Digi-Wave Docks, four DLTs, four 3.5mm to RCA cables, conference microphone if desired

Conference Room 1

Conference Room 2

VOLUME

POWER HEADPHONE

POWER AMPLIFIER

POWER

COMPUTER

VOLUME

POWER HEADPHONE

POWER AMPLIFIER

POWER

COMPUTER

Digi-Wave Dock Application Guide

Teleconferencing

Unit Programming

Unit

Location

Model Mode Priority Group Address

Docked *

Conf Rm 1

DLT 300

2-way:

Master 1

1 01

Presenters

Conf Rm 1

DLT 300

2-way:

Guest

02 ... 99**

Docked *

Conf Rm 2

DLT 300

2-way:

Master 1

1 01

Presenters

Conf Rm 2

DLT 300

2-way:

Guest 1

02 ... 99**

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

** Each DLT transceiver within a Group must have a unique address.

Conference Room 1 and 2 are separated by a large enough physical distance that both rooms are out of range of each other’s Digi-Wave

System. This eliminates the need to have each system on separate groups, so they can both use Group 1.

A499

Docked

DLT

Line

Output

(RCA)

In Conference Room 1, a speaker’s voice is transmitted from a DLT 100 2.0 to a docked DLT 100

2.0. The dock sends the audio through it’s outputs into a computer. The computer sends the

audio through the internet where it is received by a computer in Conference Room 2. The

computer in Conference Room 2 sends its audio to a dock that has a docked DLT 100 2.0

transceiver. A listener with a DLT or DLR in Conference Room 2 hears the audio from Conference

Room 1.

In the same manner, audio is sent from Conference Room 2 to Conference Room 1, completing

the 2-way communication circuit. Typically this type of system is coupled with a video screen in

each conference room, so the people in both locations can see and hear each other (not shown).

Line Input

(RCA)

Line Input

(RCA)

Digi-Wave Dock

(rear)

Line Output

(3.5mm

stereo)

Line Input

(3.5mm stereo)

Line Output (3.5mm stereo)

Conf Rm 1 Audio

Conf Rm 2 Audio

Dock-

Bay-

Switch

set to

“Auto”

Dock-

Bay-

Switch

set to

“Auto”

Docked

DLT

Line

Output

(RCA)

Main Presenter

Conf. Rm. 1

Desktop

Computer

INTERNET

Desktop

Computer

Digi-Wave Dock

(rear)

Main Presenter

Conf. Rm 2

CONFERENCE ROOM 1 CONFERENCE ROOM 2

Line Input

(3.5mm stereo)

Additional people

in the room

can join the

conference

with transceivers

in this same

configuration

(must have

unique

addresses

03...99)

DLT Programming:

Mode:

Priority:

Group: 1

Address: 2

Talk Mode: PnL

Talk Button: ON

Additional people

in the room

can join the

conference

with transceivers

in this same

configuration

(must have

unique

addresses

03...99)

DLT Programming:

Mode:

Priority:

Group: 1

Address: 2

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: PnL

Talk Button: ON

Digi-Wave Dock Application Guide

Range Extender

The Digi-Wave Dock can be used to extend the range of an existing Digi-wave System - for reaching a larger audience, reaching audiences

in additional rooms or areas, or for establising two-way communication that is outside the normal range of wireless operation (shown).

How it works:

In Building A, a talker’s voice is transmitted from a handheld DLT to a docked DLT. The dock sends the received audio through it’s output,

through the rst XLR cable, to the input of a second dock in Building B. The second dock has a DLT transceiver that broadcasts the audio

to a person listening with a handheld DLT. When the person in Building B speaks, audio travels from the handheld DLT, to the docked DLT,

and back along a second XLR cable to Building A where it enters the rst dock’s input, completing a two-way communication path. The

length of the range extension is limited by the type of XLR cables used, but can be as much as 500 feet or even much more.

Required Equipment:

Two Digi-Wave docks, two long XLR cables, and 4 DLT Transceivers

(2) XLR cables

Distance = 500 ft or more

Building A

Building B

Docked

DLT

Docked

DLT

Handheld

DLT

Handheld

DLT

Digi-Wave Dock Application Guide

Range Extender

Unit Programming

Unit

Location

Model Mode Priority Group Address

Docked *

Area/Rm 1

DLT 300

2-way:

Master 1

1 01

Presenter

Area/Rm 1

DLT 300

2-way:

Guest

02 ... 99*

Docked *

Area/Rm 2

DLT 300

2-way:

Master 1

1 01

Presenter

Area/Rm 2

DLT 300

2-way:

Guest 1

02 ... 99*

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

** Each unit within a Group must have a unique address.

A500

Docked

DLT

in 2-way

Master

Chaiman

mode

ANALOG

LINE

OUTPUT

(XLR)

Digi-Wave Dock

(rear)

Docked

DLT

in 2-way

Master

Chaiman

mode

ANALOG

LINE

INPUT

(XLR)

ANALOG

LINE

OUTPUT

(XLR)

AREA / ROOM 1

Presenter

Digi-Wave Dock

(rear)

AREA / ROOM 2

Presenter

Area/Room 1 Area/Room 2

Distance = 500 feet or more

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: Ptt or PnL

Talk Button: ON

ANALOG

LINE

INPUT

(XLR)

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: Ptt or PnL

Talk Button: ON

Bay switch

set to “Auto”

Bay switch

set to “Auto”

Digi-Wave Dock Application Guide

Interpretation with Wireless Presenter

The Digi-Wave Dock can be used to easily connect an IC-2 Interpreter’s console and provide a wireless transceiver for the main presenter

(oor). The audience hears the interpreted language (from the IC-2 console) on Channel 1, or the original presenter on Channel 0.

How it works:

The main presenter’s voice (i.e. English) is transmitted from a portable DLT in 1-way mode on Ch. 0, to a docked DLT in Interpreter Mode

on Ch. 1. The dock sends the presenter’s voice through an XLR cable to the Floor input on the IC-2. The interpreter hears the presenter’s

voice and interprets into Spanish. Spanish comes back from the IC-2 to the Dock on an XLR cable. The docked DLT broadcasts the

interpreter’s voice to the audience listening with DLR receivers on Channel 1.

Additional languages (Channels 2-14) require daisy-chaining additional IC-2’s and additional Dock Bays, one for each interpreted language.

In this example just the rst interpreted language/IC-2/dock is shown.

Note that this “Floor-In” method need only be connected on the rst IC-2 when daisy-chaining a system, as the oor will be carried on the

bus to each IC-2 in the chain.

Required Equipment:

One Digi-Wave dock, one IC-2 Interpreters Console, 2 DLT Transceivers, 2 XLR cables, audience DLRs as required.

Digi-Wave Dock Application Guide

Interpretation with Wireless Presenter

Unit Programming

Unit

Location

Model Mode Priority Group Channel

Docked *

DLT 300

1-way - Interpreter:

Guest 1 0

Wireless

Presenter

Ch. 0

DLT 300

1-way - Main Speaker:

Master 1 1

Audience

Members

DLR 360 - - 1 0-14

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

The Audience listens to the Floor or interpreted channels. Docked unit is Ch. 1-14, one channel per language.

A503

Analog

Line Input

(XLR)

Digi-Wave Dock (rear)

Analog

Line Output

(XLR)

Analog

Line Input

(XLR)

Analog

Line Output

(XLR)

IC-2 (rear)

DLT Programming:

Mode:

Priority:

Group: 1

Channel: 0

Talk Mode: PnL

Talk Button: ON

Dock Bay Switch

set to “Auto”

DLR Programming:

Group: 01

Channel: 00 English,

or 01 Spanish

Audience hears English on Ch. 0 from portable DLT

or Spanish on Ch. 1 from docked DLT

Main Presenter (English)

Interpreter’s Voice (Spanish)

DLT Programming:

Mode:

Priority:

Group: 1

Channel: 1

Talk Mode: PnL

Talk Button: ON

Docked DLT

Audience

Wireless Presenter

Digi-Wave Dock Application Guide

Two-Way, Two-Language Question and Answer

This solution can be used for two groups who speak dierent languages and need a back-and-forth dialogue. A single interpreter

alternates between languages, rst interpreting English to Spanish, then interpreting Spanish to English, and so on. The Digi-Wave Dock

can be used to easily connect an IC-2 Interpreter’s console for this setup. In this example the audience can ask questions and hear the

answers in their language ( English on Group 1, or Spanish on Group 2).

How it works:

By using the Ch. 2 Out and Relay-In on the IC-2, the Interpreter hears Group 1 (English) while interpreting to Group 2 (Spanish). If a

question is asked in Spanish, the interpreter switches to “Relay-In/Ch 2 Out OFF” mode to hear the question in Spanish and interprets

Spanish back to English. English travels back from the IC-2 in the opposite direction.

Audience members choose the Group for whichever language they want (Group 1 for English, or Group 2 for Spanish). The Audience

stays in their Group (they don’t need to change Groups), and they can ask questions, make statements, and hear questions and answers/

statements in their language. When anyone in either group asks a question, the audience members hear it in their language, and they also

hear the answer in their language.

Required Equipment:

One Digi-Wave dock, One IC-2 Interpreter’s Console, two DLTs, 3 XLR cables, one XLR-RJ45 IC-2 cable, audience DLTs/DLRs as required.

1. Question

asked in

English

Moderator

listening

not speaking

Interpreter

Audience hears all

Questions and Answers

in their Language

2. Question

interpreted

and heard in

Spanish

3. Answer

spoken in

Spanish

4. Answer

interpreted

and heard in

English

Digi-Wave Dock Application Guide

A585

Order of speaking:

English

Spanish

Audience Member

speaks 1st Question

in English

Interpreter

interprets1st Question

English -> Spanish

Audience Member

speaks 1st Answer

in Spanish

delay

Interpreter switches interpretation mode on IC-2 and begins interpreting the other language.

Interpreter

interprets 1st Answer

Spanish -> English

Audience Member

speaks 2nd Question

in English

delay

Interpreter

interprets 2nd Question

English -> Spanish

Audience Member

speaks 2nd Answer

in Spanish

Interpreter

interprets 2nd Answer

Spanish -> English

delay

End of dialog. The person speaking has finished.

delay

There is a slight delay when the Interpreter starts listening to a new line of dialog and begins interpreting to the other language.

Two-Way, Two-Language Question and Answer

Unit Programming

Unit

Location

Model Mode Priority Group Address

Dock 1

Bay 1 *

(English)

DLT 300

2-way

Master 1

1 01

Dock 1

Bay 2 *

(Spanish)

DLT 300

2-way

Master 1

2 01

Spanish

Audience

Ch. 1

DLT 300

presenter

2-way

Guest

02 ... 99 **

DLR 360

listeners

- -

English

Audience

Ch. 2

DLT 300

presenter

2-way

Guest

02 ... 99 **

DLR 360

listeners

- -

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

** Each unit within a Group must have a unique address.

Digi-Wave Dock Application Guide

A505

Docked

DLT

Group 1

English

Analog

Line Input

(XLR)

Digi-Wave

Dock (rear)

Analog

Line Input

(XLR)

Analog

Line Input

(XLR)

Docked

DLT

Group 2

Spanish

DLT Programming:

Mode:

Priority:

Group: 1

Address: 02...99*

Talk Mode: PnL

Talk Button: ON

Bay switches

set to “Auto”

Audience members

with DLRs

listen to

Group 1 English

3. Audience member answers

in Spanish

1. Audience member asks English question

Spanish

(Group 2)

English

(Group 1)

Interpreter translating

English to Spanish

on Group 2

or Spanish to English

on Group 1

2. Interpreter speaks question in Spanish

4. Interpreter speaks answer in English

DLT Programming:

Mode:

Priority:

Group: 1

Address: 01

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 2

Address: 01

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 2

Address: 02...99*

Talk Mode: PnL

Talk Button: ON

DLR Programming:

Group: 01

Address: 02...99*

DLR Programming:

Group: 02

Address: 02...99*

Audience members

with DLTs

can ask questions

and hear answers

in Group 1 English

Audience members

with DLTs

can ask questions

and hear answers

in Group 2 Spanish

Audience members

with DLRs

listen to

Group 2 Spanish

Digi-Wave Dock Application Guide

Five Simultaneous Talkers with a 2.0 System

The 2.0 series Digi-Wave System is limited to two simultaneous talkers within the wireless system. Now the Digi-Wave Dock can be used

to add three additional speakers for a total of ve. This scenario is set up as one-way communication from the presenters to the audience.

In this example, a city council meeting has ve council members that need to speak at any given time. The audience needs to hear all ve

council members. Since all council members are sitting at the same table, they can hear each other speak, and do not require two-way

communication with each other. The system example here allows the audience to hear all ve council members.

Note that many other congurations are possible to allow a free-oating transceiver for audience questions/comments - and in that case

this would have to be set up as a two-way communication system, with transceivers in the dock. A wireless microphone system could be

mixed into the dock if a wireless microphone system is available.

How it works:

This example takes advantage of the dock’s ability to mix input signals. By combining inputs at the rst dock, the voices of Council

Members 2 & 3 (Group 2) are combined with the voices of Council Members 4 & 5 (Group 3), then combined with the voice of Council

Member 5 (Group 1). The combined audio from all groups is transmitted out to the audience on Group 1.

Required Equipment:

Two Digi-Wave docks, six DLTs (1 docked, 5 for talkers), two DLRs (both docked), one stereo RCA cable, one XLR cable, audience DLTs/

DLRs as required.

l M

embe

Group 3

Group 2

Group 1

(All ve voices)

Group 1

Digi-Wave Dock Application Guide

Five Simultaneous Talkers with a 2.0 System

Unit Programming

Unit

Location

Model Mode Priority Group Address

Dock 1

Bay 1 *

DLT 100 2.0

2-way

Chairman Master

01**

Dock 1

Bay 2 *

DLR 60 2.0 - - 2 -

Dock 2

Bay 1 *

DLR 60 2.0 - - 3

Council

Member

DLT 100 2.0

2-way

Chairman Slave

02 **

Council

Member

DLT 100 2.0

2-way

Chairman Master

01 **

Council

Member

DLT 100 2.0

2-way

Chairman Slave

02 **

Council

Member

DLT 100 2.0

2-way

Chairman Master

01 **

Council

Member

DLT 100 2.0

2-way

Chairman Slave

02 **

Audience DLR 60 2.0 - - 1

* Docked DLT must have it’s bay switch set to “Auto”. This keeps the battery charged and locks the TALK button on. When

the Dock gets powered up the DLT will begin transmitting automatically. When listeners enter the room, their receivers (or

transceivers) will sync to the docked unit and begin receiving audio.

Docked DLRs should also have the bay switch set to “Auto”; this keeps them powered up and they begin receiving when the

dock powers up and the Master is found.

** Each unit in a Group must have a unique address.

Digi-Wave Dock Application Guide

A510

Taking advantage of the dock’s ability to mix input signals, this configuration alllows 5 people to talk at the same time. By daisy-chaining inputs from one dock to the next, a

speaker’s voice is mixed in, one at a time, to the end of the chain. The return connection from the last bay’s output back to the first bay’s input completes the chain, allowing

everyone to hear, and speak to, each other.

Digi-Wave

Dock (rear)

DLT

Transceiver

Group 1

DLR

Receiver

Group 2

DLR

Receiver

Group 3

Audience

DLRs

(Group 1)

Standard

RCA cable

Standard

XLR cable

DLT Programming:

Mode:

Priority:

Group: 3

Address: 2

Talk Mode: PnL

Talk Button: ON

DLR Programming:

Group: 02

Council

Member #5

DLT

Group 1

DLT Programming:

Mode:

Priority:

Group: 1

Address: 1

Talk Mode: PnL

Talk Button: ON

DLR Programming:

Group: 03

Council

Member #1

DLT

Group 2

Council

Member #2

DLT

Group 2

Council

Member #3

DLT

Group 3

Council

Member #4

DLT

Group 3

DLT Programming:

Mode:

Priority:

Group: 2

Address: 1

Talk Mode: PnL

Talk Button: ON

DLR Programming:

Group: 01

Group 1

Group 2

Group 3

Digi-Wave

Dock (rear)

Dock bay

not used

Bay switches

set to “Auto”

Bay switch

set to “Auto”

Council Members

1 & 2

Council Members

3 & 4

DLT Programming:

Mode:

Priority:

Group: 3

Address: 1

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 2

Address: 2

Talk Mode: PnL

Talk Button: ON

DLT Programming:

Mode:

Priority:

Group: 1

Address: 2

Talk Mode: PnL

Talk Button: ON

CHAIRMAN

MAS

GROUP

TALK

CHAIRMAN

MAS

GROUP

TALK

CHAIRMAN

SLV

GROUP

TALK

CHAIRMAN

MAS

GROUP

TALK

CHAIRMAN

SLV

GROUP

TALK

Digi-Wave Dock Application Guide

Extending a 2.0 Series system with 300 Series Product

The 2.0 series systems are not directly compatible with the newer 300 Series systems. However, by using the Digi-Wave Dock, these

systems can now be used together. The dock can also be used to extend the range of a 2.0 system by adding 300 Series product.

How it works:

A DLT 100 2.0 is inserted into one bay, and a DLT 300 is inserted in the second bay. The bays are tied together with standard XLR cables,

routing the outputs of each bay to the inputs of the other bay. By doing this, two-way communication is established. The DLTs are set to

2-way mode. Audio level adjustments will need to be made to balance voices.

Required Equipment:

One Digi-Wave dock, one DLT 100 2.0, one DLT 300, two XLR cables, and talker DLTs per system as required (in this example, three DLT

300’s and two DLT 100 2.0’s).

2.0 Series System

300 Series System

Page is loading ...

Williams Sound Application Digi-wave™ Dock User guide

Williams Sound Application Digi-wave™ Dock User guide

Williams Sound Application Digi-wave™ Dock User guide

Related papers

Other documents