ANTAIRA ute-404k User manual

Brand
ANTAIRA
Model
ute-404k
Type
User manual
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
i
UTE-404K
4-Port USB2.0 to Ethernet Adapter (USB over IP)
User Manual
Version 1.1
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
ii
© Copyright 2014 Antaira Technologies, LLC
All Rights Reserved
This document contains information, which is protected by copyright. Reproduction, adaptation or translation
without prior permission is prohibited, except as allowed under the copyright laws.
Trademark Information
Antaira is a registered trademark of Antaira Technologies, LLC, Microsoft Windows and the Windows logo are the
trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. WMM and WPA are the
registered trademarks of Wi-Fi Alliance. All other brand and product names are trademarks or registered
trademarks of their respective owners.
Notice: Copyrights © 2014 by Antaira Technologies, LLC. All rights reserved. Reproduction, adaptation, or
translation without prior permission of Antaira Technologies, LLC is prohibited, except as allowed under the
copyright laws.
Disclaimer
Antaira Technologies, LLC provides this manual without warranty of any kind, expressed or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose. Antaira Technologies,
LLC may make improvements and/or changes to the product and/or specifications of the product described in this
manual, without prior notice. Antaira Technologies, LLC will not be liable for any technical inaccuracies or
typographical errors found in this guide. Changes are periodically made to the information contained herein and
will be incorporated into later versions of the manual. The information contained is subject to change without prior
notice.
Industrial USB to Ethernet Server
4-Port USB 2.0 to Ethernet Server (USB over IP)
User Manual
Version 1.1 (Sept 2014)
This manual supports the following models:
UTE-404K
This document is the current official release manual. Please check our website (www.antaira.com) for any
updated manual or contact us by e-mail ([email protected]).
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
iii
Table of Contents
1. Introduction ................................................................. 1
1.1 Product Overview ............................................... 1
1.2 Product Features ............................................... 1
1.3 Product Hardware Features ............................... 2
1.4 Package Contents .............................................. 2
2. Hardware Description ................................................. 3
2.1 Physical Layout .................................................. 3
2.2 LED Indicators .................................................... 4
3. Hardware Installation .................................................. 5
3.1 Installation steps ................................................ 5
4. Software Installation ................................................... 6
5. Technical Specification .............................................. 7
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
1
1. Introduction
The UTE-404K is a 4-Port USB2.0 to Gigabit Ethernet Server that is designed for a client PC to
work with the remote USB devices over a local gigabit network or internet. It supports screw lock
features for the downstream (USB type A) connectors with the screw lock USB cables, in order to
prevent disconnecting the USB cables accidentally.
The UTE-404K also provides the scalability to quickly adapt devices to new USB technologies.
Multiple modules can be added to Ethernet.
1.1 Product Overview
Antaira’s UTE-404K is an industrial 4-Port USB2.0 USB to Gigabit Ethernet Server (hereinafter
referred to as “The USB Server”). It provides an ideal solution to allow USB devices over
Internet instantly. With its Client Software, the network users can use the remote USB devices
over a local network or the Internet as if they were connected directly to the local PC.
The USB Server supports High speed USB devices such as printers, scanners, digital cameras
embedded controllers, and HMIs over the network. It is ideal for any industrial applications that
access the USB devices remotely.
1.2 Product Features
Provides 4 * USB2.0 Downstream Host Ports over Ethernet
Supports Standard USB Hub Mode: the 4 USB Devices can be Accessed by either Ethernet
Port or the Upstream USB Connector
Allows Working With Remote USB Devices as with Local Ones
Supports High Speed/Full Speed USB2.0 Peripherals
Provides IEEE 802.3 10/100/1000Mbps, Auto Cross-over Ethernet Port
DC Jack and Terminal Blocks for DC +7~24V DC Power Input
Supports Windows XP, 2003, Vista and Win 7
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
2
1.3 Product Hardware Features
System Interface and Performance
4-port USB2.0 (Type A) downstream Host
1-port 10/100/1000Tx RJ45 Ethernet port
Power Input
7~24VDC
Power connection: DC Jack or Terminal
Operating Temperature
Standard operating temperature models: 0°C to 55°C
Case/Installation
Metal Housing
Desktop or Wall Mounting
1.4 Package Contents
1-UTE-404K – 4-Port USB2.0 to Ethernet Sever
1-Product CD
1-External AC to DC power adapter
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
3
2. Hardware Description
2.1 Physical Layout
Figure 2.1, below, shows the physical layout of Antaira’s UTE-404K – 4Port USB 2.0 to Ethernet
Server.
Figure2.1 – UTE-404K Physical Layout
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
4
2.2 LED Indicators
There are few LEDs display the USB and power status located on the top side of the USB to
Ethernet Server, each of them has its own specific meaning as below table 2.2.
LED
Col
or
Description
USB Link
Green
On
USB devices are linked to Ethernet Port
Off
Not connected to Ethernet Port
Power LED
Green
On
Power input is active
Off
Power input is inactive
LAN Port
Green
On
Connected to network
Off
Not connected to network
Yellow
Blinking
Transferring data on Ethernet
Off
No data transfer on Ethernet
DC Jack and Terminal Blocks Power Connectors:
o A 7V~24V DC Power is required for this product.
o Power is supplied from either the DC Jack or the Terminal Blocks, but not both at the
same time.
RJ45 Ethernet Connector:
o The unit comes with a 10/100/1000Mbps Ethernet port, and supports auto cross-over
feature.
Type-B USB Upstream Port Connector:
o If the type-B USB port is connected to any PC’s USB host port, the USB server will be
switched immediately to work as a simple USB hub, and the Ethernet port will be
automatically disabled.
o Please make sure the Ethernet is not accessing the USB devices (the USB devices
are in the free device state), otherwise, the USB devices may not function properly.
Table 2.2 – LED Indicators of UTE-404K
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
5
3. Hardware Installation
3.1 Installation steps
1. Use static electricity discharge precautions
Remove possible static discharge potential from any objects that the Adapter may come in
contact with before installation. This can be accomplished by touching a bare metal chassis
rail after the power turned off.
2. Attached the DC power source
There are 2 connectors can be added the power to the unit. One is the DC Jack (by the AC
/DC Adapter) and the other is the 2-pin terminal blocks.
3. Connecting LAN cable:
Use a standard straight-through Ethernet cable to connect to a Hub or Switch. The unit
supports auto cross-over feature.
4. Connect the USB Server’s USB ports to USB devices
Typical Connection Diagram:
Figure 3.1 – Typical UTE-404K connection diagram
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
6
4. Software Installation
The USB Server comes with an user friendly client software which maps USB devices connected to
the USB server onto the local host machine.
To access the USB devices on the USB Server, each Client PC should install this GUI utility - USB
Server Program. This GUI Utility provides Device Mapping functionality for a user to connect and
disconnect various devices found on the network. It also includes a USB Server Manager that lists
and provides option to configure various setting on the USB server remotely.
The Utility was shipped in an Install Shield in the following folder on the driver CD:
To install the “Install Shield”, please open the product CD and go to the folder as above figure 4.1,
double click the Install.exe program in the folder, follow the instruction of the installer to complete the
installation.
As soon as the utility is installed, launch the USB Server Program by double click the shortcut icon on
the desktop. Once the program was installed, the application icon will display in the system tray as
shown in the figure below. Double click the icon on the system tray to view and run the Utility on the
client PC.
Note: For the more detail about how to use this USB Server Program, please refer to the PDF
manual file in the same folder on the driver CD.
Figure 4.2 – USB Server Program location
Antaira USB to Ethernet Server
UTE-404K User Manual V1.1
7
5. Technical Specification
Table 5.1 has the technical specifications for Antaira’s UTE-404K: 4-port USB2.0 to Ethernet Server.
Standards
IEEE 802.3
10Base-T 10Mbit/s Ethernet
IEEE 802.3u
100Base-Tx Fast Ethernet
IEEE 802.3ab
1000Base-Tx Gigabit Ethernet
USB Server
USB (Downstream)
4*USB 2.0 (Type-A) - Supports Screw Lock
Mechanism
USB (Upstream)
1*USB (Type-B)
Ethernet (RJ45) Port
1*10/100/1000Tx
OS Support
Windows XP, 2003, Vista and Win 7
Mechanical
LED Indicator
1*USB Status; 1*USB upstream; 1*Power
Housing
Metal
Dimension
152 x 60.1 x 26.3 mm (5.98 x 2.36 x 1.03”)
Power
Requirement
Input Voltage
7~24VDC
Power Connection
1*DC Jack, and 1*2-Pin Terminal Block
Environmental
Limits
Operating Temperature
0° to 55° C (32° to 131° F)
Storage Temperature
-20° to 85° C (-4° to 185° F)
Operating Humidity
5 to 95% RH
Antaira Customer Service and Support
(Antaira US Headquarter) + 844-268-2472
(Antaira Europe Office) + 48-22-862-88-81
(Antaira Asia Office) + 886-2-2218-9733
Please report any problems to Antaira:
www.antaira.com / support@antaira.com
www.antaira.eu / [email protected]
www.antaira.com.tw / info@antaira.com.tw
Any changes to this material will be announced on the Antaira website.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

ANTAIRA ute-404k User manual

Brand
ANTAIRA
Model
ute-404k
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents