Posiflex CD-3603R User manual

Type
User manual
CD-3x02U/R
Newland NLS-N1 Scanner Engine
Advanced Manual
Version: A0
i
Contents
Preface ................................................................................................................................... - 4 -
Introduction ....................................................................................................................... - 4 -
Chapter Description ........................................................................................................... - 4 -
Explanation of Icons .......................................................................................................... - 5 -
Chapter 1 EasySet .................................................................................................................. - 6 -
Chapter 2 System Settings ..................................................................................................... - 8 -
Introduction ....................................................................................................................... - 8 -
Programming Barcode/Programming Command/Function ............................................... - 9 -
Use of Programming Command ........................................................................................ - 9 -
Use of Programming Barcodes ........................................................................................ - 12 -
Chapter 3 TTL-232 Interface ................................................................................................ - 48 -
Introduction ..................................................................................................................... - 48 -
Chapter 4 USB Interface ...................................................................................................... - 53 -
Introduction ..................................................................................................................... - 53 -
HID POS (POS HID Barcode Scanner) .......................................................................... - 77 -
Chapter 5 Symbologies ........................................................................................................ - 80 -
Introduction ..................................................................................................................... - 80 -
Global Settings ................................................................................................................ - 80 -
Code 128.......................................................................................................................... - 82 -
EAN-8 ............................................................................................................................. - 84 -
EAN-13 ........................................................................................................................... - 88 -
UPC-E ............................................................................................................................. - 98 -
UPC-A ........................................................................................................................... - 103 -
Interleaved 2 of 5 ........................................................................................................... - 108 -
Febraban ........................................................................................................................ - 112 -
ITF-14 ............................................................................................................................ - 119 -
ITF-6 .............................................................................................................................. - 120 -
ii
Matrix 2 of 5 .................................................................................................................. - 122 -
Code 39.......................................................................................................................... - 125 -
Codabar ......................................................................................................................... - 132 -
Code 93.......................................................................................................................... - 137 -
GS1-128 (UCC/EAN-128) ............................................................................................ - 140 -
GS1 Databar (RSS) ....................................................................................................... - 143 -
Code 11.......................................................................................................................... - 144 -
ISBN .............................................................................................................................. - 149 -
ISSN .............................................................................................................................. - 150 -
Industrial 25 ................................................................................................................... - 151 -
Standard 25 .................................................................................................................... - 154 -
Plessey ........................................................................................................................... - 157 -
MSI-Plessey................................................................................................................... - 161 -
AIM 128 ........................................................................................................................ - 165 -
PDF417 .......................................................................................................................... - 167 -
QR Code ........................................................................................................................ - 171 -
Data Matrix .................................................................................................................... - 173 -
Chapter 6 Data Formatter ................................................................................................. - 179 -
Introduction ................................................................................................................... - 179 -
Add a Data Format ........................................................................................................ - 179 -
Enable/Disable Data Formatter ..................................................................................... - 183 -
Data Format Selection ................................................................................................... - 185 -
Change Data Format for a Single Scan ......................................................................... - 186 -
Clear Data Format ......................................................................................................... - 187 -
Query Data Formats ...................................................................................................... - 188 -
Formatter Command Type 6 ......................................................................................... - 189 -
Chapter 7 Prefix & Suffix ................................................................................................... - 202 -
Introduction ................................................................................................................... - 202 -
iii
Global Settings .............................................................................................................. - 202 -
Prefix Sequence ............................................................................................................. - 203 -
Custom Prefix ................................................................................................................ - 203 -
AIM ID Prefix ............................................................................................................... - 205 -
Code ID Prefix ............................................................................................................... - 205 -
Custom Suffix ................................................................................................................ - 212 -
Data Packing .................................................................................................................. - 213 -
Terminating Character Suffix ........................................................................................ - 215 -
Chapter 8 Batch Programming .......................................................................................... - 218 -
Introduction ................................................................................................................... - 218 -
Create a Batch Command .............................................................................................. - 218 -
Create a Batch Barcode ................................................................................................. - 219 -
Use Batch Barcode ........................................................................................................ - 219 -
Appendix ............................................................................................................................ - 220 -
Digit Barcodes ............................................................................................................... - 220 -
Save/Cancel Barcodes ................................................................................................... - 223 -
Factory Defaults Table .................................................................................................. - 225 -
AIM ID Table ................................................................................................................ - 233 -
Code ID Table ............................................................................................................... - 234 -
Symbology ID Number ................................................................................................. - 235 -
ASCII Table .................................................................................................................. - 236 -
Unicode Key Maps ........................................................................................................ - 241 -
Enter Setup
- 4 -
Exit Setup
Preface
Introduction
This manual provides detailed instructions for setting up and using the CD-3202U/R
scanner engine.
Chapter Description
Chapter 1, EasySet: Introduces a useful tool you can use to set up the
CD-3202U/R scanner engine.
Chapter 2, System Settings: Introduces three configuration methods and
describes how to configure general parameters of the CD-3202U/R scanner
engine.
Chapter 3, TTL-232 Interface: Describes how to configure TTL-232
communication parameters.
Chapter 4, USB Interface: Describes how to configure USB communication
parameters.
Chapter 5, Symbologies: Lists all compatible symbologies and describes how to
configure the relevant parameters.
Chapter 6, Data Formatter: Explains how to customize scanned data with the
advanced data formatter.
Chapter 7, Prefix & Suffix: Describes how to use prefix and suffix to customize
scanned data.
Chapter 8, Batch Programming: Explains how to integrate a complex
programming task into a single barcode.
Appendix: Provides factory defaults table and a bunch of frequently used
programming barcodes.
Enter Setup
- 5 -
Exit Setup
Explanation of Icons
This icon indicates something relevant to this manual.
This icon indicates this information requires extra attention
from the reader.
This icon indicates handy tips that can help you use or
configure the engine with ease.
This icon indicates practical examples that can help you to
acquaint yourself with operations.
Enter Setup
- 6 -
Exit Setup
Chapter 1 EasySet
EasySet, developed by Fujian Newland Auto-ID Tech. Co., Ltd., is a configuration
tool for Newland’s 1D/2D handheld barcode scanner, fixed mount barcode scanners
and OEM scan engines. Its main features include:
View device & configuration information of online device
Configure device
Updatefirmwareof online device
Load/modify existing XML configuration file; save current settings to an XML
file
Create/print/save programmingbarcodes toa PDForWord file
View/edit/saveimagestored on online device in the original
image/BMP/JPG/TIFF format
Send serial commands to online device and receive device response
Supported languages:Chinese and English
EasySet supports 32-bit/64-bit Microsoft WinXP/Win7/Win 8/Win 8.1/Win 10
operating systems.
EasySet can communicate with device via one of the following interface: TTL-232,
USB COM Port Emulation (UFCOM driverrequired), USB CDC (UFCOM
driverrequired), USB DataPipe (UFCOM driverrequired), USB HID-POS.
Enter Setup
- 7 -
Exit Setup
Enter Setup
- 8 -
Exit Setup
Chapter 2 System Settings
Introduction
There are three ways to configure the CD-3202U/R scanner engine: Barcode
programming, command programming and Easyset programming.
Barcode Programming
The CD-3202U/R scanner engine can be configured by scanning programming
barcodes. All user programmable features/options are described along with their
programming barcodes/commands in the following sections.
This programming method is most straightforward. However, it requires manually
scanning barcodes. As a result, errors are more likely to occur.
Command Programming
The CD-3202U/R scanner engine can also be configured by serial commands sent
from the host device.
Users can design an application program to send those command strings to the
engines to perform device configuration.
EasySet Programming
Besides the two methods mentioned above, you can conveniently perform engine
configuration through EasySet too. EasySet is a Windows-based configuration tool
particularly designed for Newland products. Enabling users to gain access to decoded
data and captured images and to configure engines. For more information about this
tool, refer to the EasySet User Guide.
Enter Setup
- 9 -
Exit Setup
Programming Barcode/Programming Command/Function
The figure aboveis an example that shows you the programming barcode and
command for the Enter Setup function:
1. The No Case Conversion barcode.
2. The No Case Conversion command.
3. The description of feature/option.
4. ** indicates factory default settings.
Use of Programming Command
Besides the barcode programming method, the engine can also be configured by serial
commands (HEX) sent from the host device. All commands must be entered in
uppercase letters.
Query Commands
For query commands, the entry in the Data field in the syntax above is one of the
following characters means:
* (HEX: 2A) What is the engine’s current value for the setting(s).
& (HEX: 26) What is the factory default value for the setting(s).
^ (HEX: 5E) What is the range of possible values for the setting(s).
The value of the StoreType field in a query command can be either “@” (HEX: 40) or
“#” (HEX: 23).
A query command with the SubTag field omitted means to query all the settings
concerning a tag. For example, to query all the current settings about Code 11, you
should enter 7E 01 30 30 30 30 40 43 31 31 2A 3B 03(i.e.
Enter Setup
- 10 -
Exit Setup
~<SOH>0000@C11*;<ETX>).
Command Syntax
Prefix StorageType Tag SubTag {Data} [,SubTag {Data}] [;Tag SubTag {Data}]
[…]Suffix
Prefix: “~<SOH>0000” (HEX: 7E 01 30 30 30 30), 6 characters.
StorageType: “@” (HEX: 40) or “#” (HEX: 23), 1 character. “@” means permanent
setting which will not be lost by removing power from the engine or rebooting it; “#”
means temporary setting which will be lost by removing power from the engine or
rebooting it.
Tag: A 3-character case-sensitive field that identifies the desired command group. For
example, all USB HIDKeyboardconfiguration settings are identified with a Tag of
KBW.
SubTag: A 3-character case-sensitive field that identifies the desired parameter within
the tag group. For example, the SubTag for the keyboard layout is CTY.
Data: The value for a feature or parameter setting, identified by the Tag and SubTag.
Suffix: “;<ETX>” (HEX: 3B 03), 2 characters.
Multiple commands can be issued within one Prefix/Suffix sequence. For
configuration commands, only the Tag, SubTag, and Data fields must be repeated for
each command in sequence. If an additional command is to be applied to the same
Tag, then the command is separated with a comma (,) and only the SubTag and Data
fields of the additional commands are issued. If the additional command requires a
different Tag field, the command is separated from previous command by a semicolon
(;).
Responses
Different from command sequence, the prefix of a response consists of the six
characters of “<STX><SOH>0000” (HEX: 02 01 30 30 30 30).
The engine responds to serial commands with one of the following three responses:
<ACK>(HEX: 06) Indicates a good command which has been processed.
<NAK>(HEX: 15) Indicates a good configuration command with its Data field
Enter Setup
- 11 -
Exit Setup
entry out of the allowable range for this Tag and SubTag combination (e.g. an entry
for an inter-keystroke delay of 100 when the field will only allow 2 digits), or an
invalid query command.
<ENQ>(HEX: 05) Indicates an invalid Tag or SubTag command.
When responding, the engine echoes back the command sequence with the status
character above inserted directly before each of the punctuation marks (the comma or
semicolon) in the command.
Examples
Example 1: Enable Code 11, set the minimum and maximum lengths to 12 and 22
respectively.
Enter: 7E 01 30 30 30 30 40 43 31 31 45 4E 41 31 2C 4D 49 4E 31 32 2C 4D 41 58
32 32 3B 03
(~<SOH>0000@C11ENA1,MIN12,MAX22;<ETX>)
Response: 02 01 30 30 30 30 40 43 31 31 45 4E 41 31 06 2C 4D 49 4E 31 32 06 2C
4D 41 58 32 32 06 3B 03
(<STX><SOH>0000@C11ENA1<ACK>,MIN12<ACK>,MAX22<ACK>;<ETX>)
Example 2: Query the current minimum and maximum lengths of Code 11.
Enter: 7E 01 30 30 30 30 40 43 31 31 4D 49 4E 2A 2C 4D 41 58 2A 3B 03
(~<SOH>0000@C11MIN*,MAX*;<ETX>)
Response: 02 01 30 30 30 30 40 43 31 31 4D 49 4E 31 32 06 2C 4D 41 58 32 32 06
3B 03
(<STX><SOH>0000@C11MIN12<ACK>,MAX22<ACK>;<ETX>)
Enter Setup
- 12 -
Exit Setup
Use of Programming Barcodes
Scanning the Enter Setup barcode can enable the engine to enter the setup mode.
Then you can scan a number of programming barcodes to configure your engine. To
exit the setup mode, scan the Exit Setup barcode or a non-programing barcode, or
reboot the engine.
**Exit Setup
Enter Setup
Programming barcode data (i.e. the characters under programming barcode) can be
transmitted to the host device. Scan the appropriate barcode below to enable or
disable the transmission of programming barcode data to the host device.
**Do Not Transmit Programming
Barcode Data
Enter Setup
- 13 -
Exit Setup
Transmit Programming Barcode Data
Internal Illumination
A couple of illumination options are provided to improve the lighting conditions
during every image capture:
Normal: Illumination LEDs on the engine are turned on during image capture.
Always On: Illumination LEDs on the engine keep on after the engine is
powered on.
Off: Illumination LEDs on the engine are off all the time.
**Normal
Off
Always On
Enter Setup
- 14 -
Exit Setup
External Illumination
**Off
Normal
Always On
Aiming
When scanning/capturing image, the engine projects an aiming pattern which allows
positioning the target barcode within its field of view and thus makes decoding easier.
Normal: The engine projects an aiming pattern only during barcode
scanning/capture.
Always On: Aiming pattern is constantly on after the engine is powered on.
Off: Aiming pattern is off all the time.
Enter Setup
- 15 -
Exit Setup
**Normal
Off
Always On
Good Read LED
The LED can be programmed to be On or Off to indicate good read.
**On
Off
Enter Setup
- 16 -
Exit Setup
Good Read LED Duration
This parameter sets the amount of time that the Good Read LED to remain on
following a good read. It is programmable in 1ms increments from 1ms to 2,500ms.
**Short (20ms)
Medium (120ms)
Long (220ms)
Prolonged (320ms)
Custom (1 10,000ms)
Enter Setup
- 17 -
Exit Setup
Set the Good Read LED duration to 800ms:
1. Scan the Enter Setup barcode.
2. Scan the Custom barcode.
3. Scan the numeric barcodes “8”, “0” and “0” from the
“Digit Barcodes” section in Appendix.
4. Scan the Save barcode from the “Save/Cancel Barcodes”
section in Appendix.
5. Scan the Exit Setup barcode.
Power On Beep
The engine can be programmed to beep when it is powered on. Scan the Off barcode
if you do not want a power on beep.
**On
Off
Enter Setup
- 18 -
Exit Setup
Good Read Beep
Scanning the Off barcode can turn off the beep that indicates successful decode;
scanning the On barcode can turn it back on.
**On
Off
Good Read Beep Duration
This parameter sets the length of the beep the engine emits on a good read. It is
programmable in 1ms increments from 20ms to 300ms.
Short (40ms)
**Medium (80ms)
Enter Setup
- 19 -
Exit Setup
Long (120ms)
Custom (20-300ms)
Set the Good Read Beep duration to 200ms:
1. Scan the Enter Setup barcode.
2. Scan the Custom barcode.
3. Scan the numeric barcodes “2”, “0” and “0” from the
“Digit Barcodes” section in Appendix.
4. Scan the Save barcode from the “Save/Cancel Barcodes”
section in Appendix.
5. Scan the Exit Setup barcode.
Good Read Beep Frequency
This parameter is programmable in 1Hz increments from 20Hz to 20,000Hz.
Extra Low (800Hz)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242

Posiflex CD-3603R User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI