Posiflex CD-3604U/R Quick setup guide

Brand: Posiflex

Model: CD-3604U/R

Type: Quick setup guide

Package Contents

CD-3604U

 2D image scanner

 USB cable

 Quick setup guide

CD-3604R

 2D image scanner

 RS-232 cable

 Quick setup guide

Parts of the 2D Image Scanner

Default Settings

Scanning the following barcode can restore the engine to the factory defaults.

Before setting, please scan the Enter Setup barcode on P.3. If your CD-

3604U/R is planned to be installed into our Posiflex kiosk model, please scan

the barcode on the right side. After setting, please scan the Exit Setup barcode

on P.3.

Trigger Button1

Scan Window

w/ Object Detector

Mounting Screw Hole

Beeper Hole

Interface Cable Connector

CD-3604 (U/R)

2D Image Scanner

Quick Setup Guide

18091901010 Ver. A0

http://www.posiflex.com

Restore Kiosk Trigger Default

(For Kiosk Model)

$>:S010186.<

Restore All Factory Defaults

Scanner Maintenance

The scanner is designed for long-term trouble-free operation and rarely requires

any maintenance. Only an occasional cleaning of the scanner window is necessary

in order to remove dirt and fingerprints.

Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to

avoid the scan window from being scratched and damaged. The scan window can

be cleaned while the scanner is running.

The standard interface cable is attached to the scanner with a 10-pin modular

connector. When the connector is properly seated, it is secured in the scanner by a

flexible retention tab. The cable is designed to be field replaceable. Replacement

cables can be obtained from your authorized distributor. To replace the cable, take

the following steps.

1. Make sure the power of both the host terminal and the scanner is powered off.

2. Disconnect the old scanner cable from the host terminal.

3. Press down the retention tab, and gently pull out the cable.

4. Insert the new interface cable into the bottom of the scanner until it clicks.

Then, plug the new cable into the host.

Troubleshooting

This section contains information about how to solve problems that you may

encounter when operating the scanner. If a trouble occurs, please refer to the

following diagnostic tips as a mean to solve the trouble. However, before referring

to the tips, make sure that the scanner is installed well. If the problem remains,

contact your dealer.

Problem

Diagnostic Tips

The scanner is on but cannot read

any barcode.

The scanner window is dirty. Clean the scanner

window as described in the Scanner

Maintenance section.

The presented barcode type is not enabled. Use

this guide to tell the scanner to accept that type

of barcode.

The host terminal has disabled the scanner.

Check the setup of host terminal.

The barcode type presented is not supported by

the scanner.

The scanner does not accept more

than two or three barcode labels.

Determine whether the required barcode types

are enabled or not.

A stray barcode is sitting somewhere in the

scanner field of view. Remove all barcode labels

from the scanner’s scan volume and try again.

Problem

Diagnostic Tips

The scanner cannot send the data to the POS

system. Make sure that the scanner is installed

well and your host POS system is ready to

receive data.

A barcode is read by the scanner

but not accepted by the POS

system.

The communication settings of the system port

and the scanner do not match. Adjust the settings

to make them match to each other.

The scanner is not installed well. Contact your

dealer for the proper installation. The software

running on the POS system does not support the

data format of the barcode label.

When a barcode stays close to the

scanner, the barcode cannot be read

automatically by the scanner.

Check whether or not you have enabled the

Manual Trigger mode. If you have enabled this

mode accidentally, please disable the Manual

Trigger mode by scanning the “Disable trigger”

barcode in the advanced user manual.

Programming Codes

Below are some suggestion you need to bear in mind while scanning labels:

1. The barcode labels shown in bold and black are default factory settings.

2. Please cover the unwanted codes for scanning the specific barcode required

for the programming to prevent confusion in code scanning.

3. Use the user manual downloaded from our global website for advanced

programming.

4. While scanning the setup barcode labels provided in the quick guide, you need

to pull the trigger to initiate the decoding process.

Programming Barcodes

Scanning the Enter Setup barcode can enable the engine to enter the setup

mode. Then you can scan a number of programming barcodes to configure

your engine. To exit the setup mode, scan the Exit Setup barcode or a non-

programming barcode, or reboot the engine.

Enter Setup

Exit Setup

Firmware Version

Scan the below barcode to retrieve the current firmware version.

USB/RS-232 Interface

There are four options for USB connection:

 USB HID-KBW: In keyboard mode, place the mouse cursor on the notepad,

etc., and the data will be entered into the notepad after successful decoding.

 USB HID POS: Use HID POS protocol to communicate.

 USB Virtual COM: Enumerate into a virtual serial port. At this time, the PC

needs to use the serial port assistant to receive data.

 RS-232 Interface: Rs232 interface is a common way to connect scanner and

host equipment (such as PC, POS and other equipment). When using the

RS232 interface, the scanner and the host device must match the

communication parameter configuration completely to ensure smooth

communication and correct content.

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

USB HID-KBW (default)

$>:S0F0116.<$

USB HID POS

$>: S0F0516.<$

USB Virtual COM

$>: S0F0216.<$

RS232

$>: S0F0016.<$

Trigger Mode

 Manual Mode: Press the button to trigger the reading, and release the button

to end the reading. If the reading is successful or the reading time exceeds

the single reading time, the reading will end.

 Automatic Scanning Mode: In the induction mode, you can activate the

scanner to work by pressing a button, sending a command, or auto-sensing.

 Continuous Scanning Mode: Under continuous Scanning Mode，after a

period of time when a reading is successful, it will automatically start the

next reading. Start or end scanning until the button is pressed and released

(buttons and commands can be terminated and reopened)

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Manual Mode (default)

(Command + Button)

$>: S03001A.<$

Automatic Mode

(Command+Button+Auto-sensing)

$>: S03011A.<$

Continuous Mode

(Button+Command)

$>: S03021A.<$

Illumination

A couple of illumination options are provided to improve the lighting conditions

during every image capture:

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Off

$>:S0C0000.<$

Reading On (default)

$>:S0C0400.<$

Always On

$>:S0C0800.<$

Aiming

When scanning/capturing image, the engine projects an aiming pattern which

allows positioning the target barcode whining its field of view and thus makes

decoding easier.

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Off

$>:S300000.<$

Reading On (Lit when reading, default)

$>:S301000.<$

Always On

$>:S302000.<$

Good Read Beep Frequency

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Low

$>:SFFDA27.<$

Medium

$>:SFF4B27.<$

Loud (default)

$>:SFF2527.<$

Prompt Tone Duration

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

40ms (Short)

$>:SFF1F28.<$

80ms (Middle) (default)

$>:SFF3E28.<$

120ms (Long)

$>:SFF5D28.<$

Good Read Tone Sound

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Low

$>:S030018.<$

Medium

$>:S030118.<$

Loud

$>:S030218.<$

Enabling/Disabling of readable codes

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

Enable All Barcodes

$>:S010187.<$

Disable All Barcodes

$>:S010087.<$

Enable All 1D Codes

$>:S020287.<$

Disable All 1D Codes

$>:S020087.<$

Enable All 2D Codes

$>:S040487.<$

Disable All 2D Codes

$>:S040087.<$

Enable Code128/AIM128/EAN128/NL128 (default)

$>:S010188.<$

Disable Code128/AIM128/EAN128/NL128

$>:S010088.<$

Enable UPC/EAN/ISSN/ISBN (default)

$>:S010189.<$

Disable UPS/EAN/ISSN/ISBN

$>:S010089.<$

Enable Codabar

$>:S01018C.<$

Disable Codabar (default)

$>:S01008C.<$

Enable Code 39 (default)

$>:S01018A.<$

Disable Code 39

$>:S01008A.<$

Enable Code 32 (default)

$>:S0101AB.<$

Disable Code 32

$>:S0100AB.<$

Enable Code 93 (default)

$>:S01018D.<$

Disable Code 93

$>:S01008D.<$

Enable Code 11

$>:S01018F.<$

Disable Code 11 (default)

$>:S01008F.<$

Enable ITF-25/ITF-14/ITF-6/Deutsche12/Deutsche14 (default)

$>:S01018B.<$

Disable ITF-25/ITF-14/ITF-6/Deutsche12/Deutsche14

$>:S01008B.<$

Enable Industrial 25

$>:S010193.<$

Disable Industrial 25 (default)

$>:S010093.<$

Enable Matrix 25

$>:S01018E.<$

Disable Matrix 25 (default)

$>:S01008E.<$

Enable NEC 25/Japan Matrix 25

$>:S01019E.<$

Disable NEC 25/Japan Matrix 25 (default)

$>:S01009E.<$

Enable Standard 25

$>:S010192.<$

Disable Standard 25 (default)

$>:S010092.<$

Enable Data Logic 25

$>:S01019F.<$

Disable Data Logic 25 (default)

$>:S01009F.<$

Enable MSI-Plessey

$>:S010191.<$

Disable MSI-Plessey (default)

$>:S010091.<$

Enable Plessey

$>:S0101A0.<$

Disable Plessey (default)

$>:S0100A0.<$

Enable RSS-EXP/RSS_14/GS1 Data

$>:S010190.<$

Disable RSS-EXP/RSS_14/GS1 Data (default)

$>:S010090.<$

Enable Telepen

$>:S010194.<$

Disable Telepen (default)

$>:S010094.<$

Enable Pharma Code One-Track

$>:S0101A1.<$

Disable Pharma Code One-Track (default)

$>:S0100A1.<$

Enable Pharma Code Two-Track

$>:S0101A2.<$

Disable Pharma Code Two-Track (default)

$>:S0100A2.<$

Enable AZTEC

$>:S01019A.<$

Disable AZTEC (default)

$>:S01009A.<$

Enable CODABLOCK A

$>:S01019C.<$

Disable CODABLOCK A (default)

$>:S01009C.<$

Enable CODABLOCK F

$>:S01019D.<$

Disable CODABLOCK F (default)

$>:S01009D.<$

Enable Data Matrix (default)

$>:S010197.<$

Disable Data Matrix

$>:S010097.<$

Enable MaxiCode

$>:S010199.<$

Disable MaxiCode (default)

$>:S010099.<$

Enable PDF417 (default)

$>:S010195.<$

Disable PDF417

$>:S010095.<$

Enable Micro PDF

$>:S0101A3.<$

Disable Micro PDF (default)

$>:S0100A3.<$

Enable Micro QR

$>:S010198.<$

Disable Micro QR (default)

$>:S010098.<$

Enable Han Xin Code

$>:S01019B.<$

Disable Han Xin Code (default)

$>:S01009B.<$

Enable DOTCODE

$>:S0101AE.<$

Disable DOTCODE (default)

$>:S0100AE.<$

Allow ID Card Reading

$>:S0101AC.<$

Prohibit ID Card Reading (default)

$>:S0100AC.<$

Allow Passport Reading

$>:S0202AC.<$

Prohibit Passport Reading

$>:S0200AC.<$

Baud rate settings (Only for CD-3604R)

Baud rate is the number of bits of data transmitted per second. Set the baud rate to

match the host requirements.

Before setting, please scan the Enter Setup barcode on P.3.

After setting, please scan the Exit Setup barcode on P.3.

1200bps

$>:S0F0047.<$

2400bps

$>:S0F0147.<$

4800bps

$>:S0F0247.<$

9600bps (default)

$>:S0F0347.<$

19200bps

$>:S0F0547.<$

38400bps

$>:S0F0647.<$

57600bps

$>:S0F0747.<$

115200bps

$>:S0F0847.<$

Specifications

Item

Characteristics

Performance

Image Sensor

1280*800 CMOS

Illumination

White LED

Aiming

Red LED

Symbologies

QR, Micro QR, PD417, Micro PDF,

Data Matrix, Aztex, Maxicode, Han

Xin, etc.

Code 128, EAN-13, EAN-8, Code 39,

UPC-A, UPC-E, Codabar, Interleaved

2 of 5, ITF-6, ITF-14, ISBN, Code

93, UCC/EAN-128, GS1 Databar,

Matrix 2 of 5, Standard 2 of 5,

Plessey, MSI-Plessey, etc.

Resolution*

≧4mil

Typical Depth of Field*

EAN-13 (13mil): 40mm-360mm

PDF417 (6.67mil): 30mm-200mm

Data Matrix (10mil): 30mm-220mm

Code 39 (5mil): 40mm-180mm

QR Code (20mil): 40mm-330mm

Min. Symbol Contrast

≧25%

Scan Angle**

Roll: 360°, Pitch: ±50°, skew: ±50°

Field of View

Horizontal 49.6°, Vertical 37.2°

Electrical

Interface

RS-232, USB

*Test conditions: T=25°C Illumination=200lux using incandescent lamp.

**Test conditions: Scan Distance=(min. DOF + max. DOF)/2; T=25°C;

Illumination=200lux using incandescent lamp.

※

The product information and specifications are subject to change without

prior notice. To get the detailed information of the CD-3604U/R, please

check this model from Posiflex Global Website.

(http://www.posiflex.com/en-global/Download/download). Or download

the advanced manual for more detailed settings.

Posiflex CD-3604U/R Quick setup guide

Posiflex CD-3604U/R Quick setup guide

Posiflex CD-3604U/R Quick setup guide

Related papers

Other documents