Posiflex CD-3203U is a 2D image scanner which enables you to read a wide range of barcodes, including Code 39, Code 128, UPC, PDF417, QR Code, and DataMatrix. It features an image resolution of 640 horizontal x 400 vertical pixels and a field of view of 42.0゜horizontal and 28.0゜vertical. The scanner is equipped with a hyper red 660nm LED aiming element and a 610nm LED aiming dot with a brightness level of 130 fcd nominal. It has a reading range of 30~120mm for Code 39 with a resolution of 0.127, and a maximum reading range of 570mm for DataMatrix with a resolution of 0.31.
Posiflex CD-3203U is a 2D image scanner which enables you to read a wide range of barcodes, including Code 39, Code 128, UPC, PDF417, QR Code, and DataMatrix. It features an image resolution of 640 horizontal x 400 vertical pixels and a field of view of 42.0゜horizontal and 28.0゜vertical. The scanner is equipped with a hyper red 660nm LED aiming element and a 610nm LED aiming dot with a brightness level of 130 fcd nominal. It has a reading range of 30~120mm for Code 39 with a resolution of 0.127, and a maximum reading range of 570mm for DataMatrix with a resolution of 0.31.
2
Scanner Maintenance
The scanner is designed for long-term trouble-free operation and rarely
requires any maintenance. Only an occasional cleaning of the scanner window
is necessary in order to remove dirt and fingerprints.
Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to
avoid the scan window from being scratched and damaged. The scan window
can be cleaned while the scanner is running.
The standard interface cable is attached to the scanner with a 10-pin modular
connector. When the connector is properly seated, it is secured in the scanner
by a flexible retention tab. The cable is designed to be field replaceable.
Replacement cables can be obtained from your authorized distributor. To
replace the cable, take the following steps.
1. Make sure the power of both the host terminal and the scanner is powered
off.
2. Disconnect the old scanner cable from the host terminal.
3. Press down the retention tab, and gently pull out the cable.
4. Insert the new interface cable into the bottom of the scanner until it clicks.
Then, plug the new cable into the host.
LED Indication
Status
Explanation
Blue LED flashes one time
Good read
Troubleshooting
This section contains information about how to solve problems that you may
encounter when operating the scanner. If a trouble occurs, please refer to the
following diagnostic tips as a mean to solve the trouble. However, before
referring to the tips, make sure that the scanner is installed well. If the problem
remains, contact your dealer.
Problem
Diagnostic Tips
The scanner is on but cannot read
any barcode.
The scanner window is dirty. Clean the scanner
window as described in the Scanner
Maintenance section.
The presented barcode type is not enabled. Use
this guide to tell the scanner to accept that type
of barcode.
The host terminal has disabled the scanner.
Check the setup of host terminal.
The barcode type presented is not supported by
the scanner.
3
Problem
Diagnostic Tips
The scanner does not accept more
than two or three barcode labels.
Determine whether the required barcode types
are enabled or not.
A stray barcode is sitting somewhere in the
scanner field of view. Remove all barcode labels
from the scanner’s scan volume and try again.
The scanner cannot send the data to the POS
system. Make sure that the scanner is installed
well and your host POS system is ready to
receive data.
A barcode is read by the scanner
but not accepted by the POS
system.
The communication settings of the system port
and the scanner do not match. Adjust the settings
to make them match to each other.
The scanner is not installed well. Contact your
dealer for the proper installation. The software
running on the POS system does not support the
data format of the barcode label.
When a barcode stays close to the
scanner, the barcode cannot be read
automatically by the scanner.
Check whether or not you have enabled the
Manual Trigger mode. If you have enabled this
mode accidentally, please disable the Manual
Trigger mode by scanning the “Disable trigger”
barcode in the advanced user manual.
Programming Codes
Below are some suggestion you need to bear in mind while scanning labels:
1. The barcode labels shown with “ * ” are default factory settings.
2. Please cover the unwanted codes for scanning the specific barcode
required for the programming to prevent confusion in code scanning.
3. Use the user manual downloaded from our global website for advanced
programming.
4. While scanning the setup barcode labels provided in the quick guide, you
need to pull the trigger to initiate the decoding process.
Report Version
Scan the bar code below to report the version of software currently installed in
the decoder.
4
Report Decoder Manufacturing Information
Scan the bar code below to report the part number, serial number, and
manufacture date of the decoder.
Report Scan Engine Manufacturing Information
Scan the bar code below to report the part number, serial number, and
manufacture date of the scan engine.
Default Settings
Set Factory Defaults clears all custom default values and sets the factory
default values.
USB Device Type
Scan one of the following barcodes to select the USB device type.
NOTE: When changing USB Device Types, the engine resets and issues the
standard startup beep sequences.
NOTE: Before selecting USB CDC Host (Virtual COM), install the USB
CDC driver located at Posiflex Global Website.
If using Windows XP, this self-contained driver provides functionality but
prompts with a warning message as Microsoft no longer re-certifies drivers for
this operating system.
5
(Virtual COM)
Trigger Mode
Standard (Level): A trigger press activates decode processing. Decode
processing continues until the bar code decodes, or you release the
trigger.
Presentation (Blink): The engine activates decode processing when it
detects a bar code in its field of view. After a period of non-use, the
LEDs turn off until the engine senses motion.
Auto Aim: The engine projects the aiming pattern when it senses motion.
A trigger press activates decode processing. After two seconds of
inactivity the aiming pattern shuts off.
Auto Aim with Illumination: The engine turns on the aiming pattern and
internal illumination LEDs when it senses motion. A trigger press
activates decode processing. After two seconds inactivity the aiming
pattern and internal illumination LEDs automatically shut off.
Host and Hardware Trigger Mode: A host command or trigger press
issues the triggering signal, which is interpreted as a level trigger option.
6
Illumination
Selecting Enable Decoding Illumination causes the engine to turn on
illumination every image capture to aid decoding. Select Disable Decoding
Illumination to prevent the engine from using decoding illumination.
Enabling illumination usually results in superior images. The effectiveness of
illumination decreases as the distance to the target increases.
7
Aiming
Select Enable Decode Aiming Pattern to project the aiming pattern during
bar code capture, or Disable Decode Aiming Pattern to turn the aiming
pattern off.
Beep After Good Decode
Scan one of the following bar codes to select whether or not the engine beeps
after a good decode. If you select Disable Beep After Good Decode, the
beeper still operates during parameter menu scanning a indicate error
conditions.
8
Enabling/Disabling of readable codes
Scan the Disable All Code Types bar code to disable all symbologies.
Scan Enable All Code Types to enable all symbologies.
9
10
11
12
13
14
15
16
17
18
19
20
Specifications
Item
Characteristics
Image Sensor
Image Resolution
640 horizontal x 400 vertical pixels
Field of View (FOV)
42.0゜horizontal, 28.0゜vertical
Illumination
System
LED
Hyper red 660nm
Pattern Angle
50.3゜horizontal, 32.0゜vertical at
50% intensity
LED Aiming
Element
LED
610nm
Aiming Dot Brightness
Level
130 fcd nominal
Reading Ranges
Code 39:
30~120mm (Resolution(0.127))
40~205mm (Resolution(0.25))
75~355mm (Resolution(0.33))
Code 128:
40~190mm (Resolution(0.25))
UPC:
60~300mm (Resolution(0.33))
PDF417:
25~220mm (Resolution(0.25))
QR Code:
10~310mm (Resolution(0.381))
DataMatrix:
15~570mm (Resolution(0.31))
Optical Resolution
5.0 mil (code 39), 6.6 mil (PDF417)
Ambient Light Immunity (Sunlight)
10000 ft. candles (107,639 lux)
Focusing Distance from Front of Engine
194mm / 7.64 inches
Interface
USB
※
The product information and specifications are subject to change without
prior notice. To get the detailed information of the CD-3203U, please
check this model from Posiflex Global Website. Or download the
advanced manual for more detailed settings.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Posiflex CD-3203U is a 2D image scanner which enables you to read a wide range of barcodes, including Code 39, Code 128, UPC, PDF417, QR Code, and DataMatrix. It features an image resolution of 640 horizontal x 400 vertical pixels and a field of view of 42.0゜horizontal and 28.0゜vertical. The scanner is equipped with a hyper red 660nm LED aiming element and a 610nm LED aiming dot with a brightness level of 130 fcd nominal. It has a reading range of 30~120mm for Code 39 with a resolution of 0.127, and a maximum reading range of 570mm for DataMatrix with a resolution of 0.31.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Zebex Z-8072 User manual
-
Zebra CS6080 Product Reference Guide
-
Zebra MS4717 Owner's manual
-
-
-
Zebra DS9308 Product Reference Guide
-
Zebra DS36X8 Product Reference Guide
-
Zebra DS9908 Owner's manual
-
-