Thermo Fisher Scientific A27-6x50 Rotor User manual

50138015-01 October 2012

Thermo Scientific

A27-6x50 Rotor

for Sorvall LYNX Superspeed Centrifuges

Instruction Manual

Visit us online to register your warranty.

www.thermoscientific.com/labwarranty

Delrin, TEFLON, and Viton are registered trademarks of DuPont. Noryl is a registered trademark of SABIC

POLYCLEAR is a registered trademark of Hongye CO., Ltd. Hypaque is a registered trademark of Amersham Health As.

RULON A and Tygon are registered trademarks of Saint-Gobain Performance Plastics. Alconox is a registered trademark

of Alconox. Ficoll is a registered trademark of GE Healthcare. Haemo-Sol is a registered trademark of Haemo-Sol. Triton

X-100 is a registered trademark of Sigma-Aldrich Co. LLC. Pyrex is a registered trademark of Corning.

All other trademarks are the property of Thermo Fisher Scientific Inc. and its subsidiaries.

Manufacturer

Thermo Fisher Scientific

Robert-Bosch-Straße 1

D - 63505 Langenselbold

Germany

Thermo Fisher Scientific Inc. provides this document to its customers with a product purchase to use in the

product operation. This document is copyright protected and any reproduction of the whole or any part of this

document is strictly prohibited, except with the written authorization of Thermo Fisher Scientific Inc.

The contents of this document are subject to change without notice. All technical information in this

document is for reference purposes only. System configurations and specifications in this document supersede

all previous information received by the purchaser.

Thermo Fisher Scientific Inc. makes no representations that this document is complete, accurate or error-

free and assumes no responsibility and will not be liable for any errors, omissions, damage or loss that

might result from any use of this document, even if the information in the document is followed

properly.

This document is not part of any sales contract between Thermo Fisher Scientific Inc. and a purchaser. This

document shall in no way govern or modify any Terms and Conditions of Sale, which Terms and Conditions of

Sale shall govern all conflicting information between the two documents.

Original instruction manual 50138015-01 printed in October 2012.

50138015-01 is a translation of 50138014-01.

Thermo Scientific A27-6x50 Rotor i

T

Preface ........................................................................................................................................ ii

Scope of Supply ........................................................................................................................ ii

Precautions ............................................................................................................................... iii

Chapter 1 Rotor Information .......................................................................................................................1

Rotor Data ..................................................................................................................1

Rotor Package ..............................................................................................................2

Rotor Accessory ...........................................................................................................2

Information on Tubes and Bottles ...............................................................................2

Chapter 2 Thermo Scientific Auto-Lock Rotor Exchange .....................................................................5

Open and Close Rotor .................................................................................................5

Rotor Installation .........................................................................................................5

Removing the Rotor ....................................................................................................6

Chapter 3 Rotor Loading ..............................................................................................................................9

Before a Run ................................................................................................................9

Proper Loading ............................................................................................................9

Improper Loading ......................................................................................................10

Maximum Loading ....................................................................................................10

Lifetime .....................................................................................................................10

Chapter 4 Aerosol-tight Applications .....................................................................................................11

Basic Principles ..........................................................................................................11

Fill Level ....................................................................................................................11

Checking the Aerosol-Tightness ................................................................................11

Chapter 5 Maintenance and Care ...........................................................................................................13

Cleaning Intervals ......................................................................................................13

Cleaning ....................................................................................................................13

Maintenance of O-Rings in Rotor Lid .......................................................................15

Disinfection ...............................................................................................................16

Decontamination .......................................................................................................17

Autoclaving ................................................................................................................18

Service of Thermo Fisher Scientific ............................................................................18

Shipping and Deposing of Centrifuge and Accessories ...............................................19

RCF-Values..................................................................................................................21

Rotor Care Guide........................................................................................................29

Routine Evaluation and Care of Your Rotor ..............................................................30

Rotor Maintenance ....................................................................................................31

Chemical Compatibility Chart .................................................................................35

Contact Information...................................................................................................41

Table of Contents

Thermo Scientific A27-6x50 Rotor ii

P

Preface

Before starting to use the rotor, read through this instruction manual carefully and follow the

instructions.

The information contained in this instruction manual is the property of Thermo Fisher Scientific; it is

forbidden to copy or pass on this information without explicit approval.

Failure to follow the instructions and safety information in this instruction manual will result in the

expiration of the sellers warranty.

Scope of Supply

If any parts are missing, please contact your nearest Thermo Fisher Scientific representative.

Article Number Quantity Check

75003007 A27-6x50 Rotor 1

75003786 Grease for Threads 1

70009824 Anti-corrosion Oil 1

75007006 Replacement O-Rings with Vacuum Grease 1

65614 Retaining Ring Pliers 1

50136234 CD with Manual 1

This symbol refers to general hazards.

CAUTION means that material damage could occur.

WARNING means that injuries or material damage or contamination could occur.

This symbol refers to biological hazards.

Observe the information contained in the instruction manual to keep yourself and your

environment safe.

Preface

iii A27-6x50 Rotor Thermo Scientific

Precautions

This symbol means that the rotor and centrifuge manual contain additional important

information.

Observe the information contained in the instruction manual to keep yourself and your

environment safe.

WARNING

In order to ensure safe operation of the A27-6x50 rotor, the following general safety

regulations must be followed:

•Do not remove the magnet at the rotor bottom.

•Do not use rotors which show any signs of corrosion and/or cracks.

•Use only with rotors which have been loaded properly.

•Never overload the rotor.

•Use only accessories which have been approved by Thermo Fisher Scientific.

Exceptions to this rule are commercially available glass or plastic centrifuge tubes,

provided they have been approved for the speed or the RCF value of the rotor.

•Please observe the safety instructions.

Please pay particular attention to the following aspects:

•The rotor may be carried by the lid handle if the lid is properly tightened.

•Rotor installation: Check that the rotor is locked properly into place before operating

the centrifuge.

•Always balance the samples.

Maximum sample density at maximum speed: 1.2

g

cm3

-----------

Thermo Scientific A27-6x50 Rotor 1

1

Rotor Information

Rotor Data

Contents

•“Rotor Data” on page 1

•“Rotor Package” on page 2

•“Rotor Accessory” on page 2

•“Information on Tubes and Bottles” on page 2

Centrifuge Sorvall Lynx 6000 Sorvall Lynx 4000

Weight of empty Rotor [kg] 5.6 5.6

Max. Cycle Number 50000 50000

Maximum permissible Load [ g ] 6x75 6x75

Maximum Speed nmax [ rpm ] 27000 24000

Maximum RCF-Value at nmax 79057 62465

K-Value at nmax 485

Radius max. / min. [ cm ] 9.7 / 2.4 9.7 / 2.4

Angle [ ° ] 34 34

Accel. / Braking Time [ s ] pending pending

Maximum Speed at 4°C [s] 25500 23500

Sample Cooling at nmax [°C] (Ambient Temperature of 23°C, Run

Time 60 Minutes)

96

Aerosol-tight*

*Tested and approved by HPA, Porton-Down, UK

Yes Yes

Maximum Autoclave Temperature (°C) 121 121

1 Rotor Information

Rotor Package

2A27-6x50 Rotor Thermo Scientific

Rotor Package

Rotor Accessory

Information on Tubes and Bottles

Description Article Number

A27-6x50 Rotor 75003007

Grease for Threads 75003786

Anti-corrosion Oil 70009824

Replacement O-Rings with Vacuum Grease 75007006

Retaining Ring Pliers 65614

CD with Manual 50136234

Description Article Number

Ultracrimp Sealing Tool and Crimp Gauge 03920

Ultracrimp Gauge Replacement 03919

Ultracrimp Extra Plugs and Caps 03999

Rotor Cap 03538

Rotor Stand 75003711

Description Article Number Type Article Number Description

PA Ultracrimp Tube 03528 Closure Included Plugs and Aluminum

Caps

Accessory 03538 Rotor Cap

Accessory 03529 Tube Racks

Accessory 03920 Sealing Tool

Nalgene PC Oak Ridge Tube 3138-0050 Closure Included PP Sealing

Nalgene PPCO Oak Ridge Tube 3139-0050 Closure Included PP Sealing

FEP Oak Ridge Tube 3114-0050 Closure Included FEP Screw Top

PP Flanged Tube 03147 Closure 03268 PP Snap-On

PC Flanged Tube 03146 Closure 03268 PP Snap-On

PA Flanged Tube 03139 – – –

SS Flanged Tube 00517 Closure 00518 SS Sealing

Tool 01014 Wrench

1 Rotor Information

Information on Tubes and Bottles

Thermo Scientific A27-6x50 Rotor 3

PC Oak Ridge Tube 314348 Closure 314347 Aluminum Sealing

Adapter 00419 1 Place/Adapter

Tool 314353 Tube Extractor Tool

PP Oak Ridge Tube 314349 Closure 314347 Aluminum Sealing

Adapter 00419 1 Place/Adapter

Tool 314353 Tube Extractor Tool

Glass Tube Adapter 00368 Optional Caps

Nalgene PC Oak Ridge Tube 3138-16 Closure Included PA Sealing

Adapter 00382 1 Place/Adapter

Nalgene PP Oak Ridge Tube 3139-16 Closure Included PA Sealing

Adapter 00382 1 Place/Adapter

PP Flanged Tube 03244 Closure 03299 PP Snap-On

Adapter 00382 1 place/adapt

PC Flanged Tube 03243 Closure 03269 PP Snap-On

Adapter 00382 1 place/adapt

Glass Tube – Adapter 00363 1 Place/Adapter

GL Pyrex® Tube 03109 Adapter 00363 1 Place/Adapter

PP Flanged Tube 03116 Closure 03266 PP Nonsealing

Adapter 00402 1 Place/Adapter

PC Flanged Tube 03115 Closure 03266 PP Nonsealing

Adapter 00402 1 Place/Adapter

Nalgene PP Oak Ridge Tube 3139-10 Closure Included PA Sealing

Adapter 00425 1 Place/Adapter

PP Oak Ridge Tube1 03929 Closure 03279 PP Sealing

Adapter 00425 1 Place/Adapter

PC Oak Ridge Tube 03020 Closure 03279 PP Sealing

Adapter 00425 1 Place/Adapter

Nalgene PC Oak Ridge Tube 3138-10 Closure Included PA Sealing

Adapter 00425 1 Place/Adapter

PA Thin-Walled Tube 03124 Adapter 00473 2 Places/Adapter

PC Flanged Tube 03120 Closure 03265 PP Snap-On

Adapter 00473 2 Places/Adapter

PP Flanged Tube 03121 Closure 03265 PP Snap-On

Adapter 00473 2 Places/Adapter

PP Flanged Tube 03105 Closure 03264 PP Snap-On

Adapter 00381 2 Places/Adapter

PP Flanged Tube 03104 Closure 03264 PP Snap-On

Description Article Number Type Article Number Description

1 Rotor Information

Information on Tubes and Bottles

4A27-6x50 Rotor Thermo Scientific

Adapter 00381 2 Places/Adapter

GL Pyrex Tube 03100 Adapter 00364 2 Places/Adapter

Conical Microtube 314352H01 Adapter 00381 2 Places/Adapter

Conical Microtube – Adapter 00381 2 Places/Adapter

Description Article Number Type Article Number Description

Thermo Scientific A27-6x50 Rotor 5

2

Thermo Scientific Auto-Lock Rotor Exchange

Open and Close Rotor

1. To tighten the lid, twist the lid handle clockwise until "hand tight". As a general rule, once the lid

is tightend to the point of resistance, tighten an additional 1/4 turn.

2. To remove the lid, twist the lid handle counter clockwise until the lid can be removed from the

rotor.

Rotor Installation

This rotor is equipped with Thermo Scientific Auto-Lock rotor exchange.

This system is used to automatically lock the rotor to the centrifuge spindle, eliminating the need to

manually bolt the rotor to the centrifuge spindle.

Proceed as follows:

1. Open the door of the centrifuge and if necessary remove any dust, foreign objects or residue from

the chamber.

Contents

•“Open and Close Rotor” on page 5

•“Rotor Installation” on page 5

•“Removing the Rotor” on page 6

Note The rotor may be carried by the lid handle if the lid is properly tightened.

CAUTION Unapproved or incorrectly combined accessories can cause serious damage to

the centrifuge.

2 Thermo Scientific Auto-Lock Rotor Exchange

Removing the Rotor

6A27-6x50 Rotor Thermo Scientific

Auto-Lock and o-ring must be clean and undamaged.

Figure 2-1. Auto-Lock

2. Place the rotor over the centrifuge spindle and let it slide slowly down the centrifuge spindle.

The rotor clicks automatically into place.

3. Check if the rotor is properly installed by lifting it slightly on the handle. If the rotor has not been

locked, place the rotor over the centrifuge spindle again.

4. Close the centrifuge door.

Removing the Rotor

To remove the rotor, proceed as follows:

1. Open the centrifuge door.

Auto-Lock

O-Ring

CAUTION Do not force the rotor onto the centrifuge spindle.

If the rotor is very light, then it may be necessary to press it onto the centrifuge spindle

with a bit of pressure.

WARNING If the rotor cannot be properly locked in place after several attempts, then the

Auto-Lock may be damaged and you are not permitted to operate the rotor.

Check for any damage to the rotor: Damaged rotors must not be used.

Keep the centrifuge spindle area of the rotor clear of objects.

Operate the rotor always with the lid closed.

CAUTION Check that the rotor is properly locked on the centrifuge spindle before each

use by pulling it at its handle.

CAUTION Be sure to check all sealings before starting any aerosol-tight applications.

2 Thermo Scientific Auto-Lock Rotor Exchange

Removing the Rotor

Thermo Scientific A27-6x50 Rotor 7

2. Grab the rotor handle with one or both hands and push down on against the Auto-Lock button. At

the same time, pull the rotor directly upwards and remove it from the centrifuge spindle. Make

sure not to tilt the rotor while doing this.

Note The rotor lid must be properly tightened to the rotor body in order to remove the rotor from

the centrifuge.

Thermo Scientific A27-6x50 Rotor 9

3

Rotor Loading

Before a Run

1. Please read and observe the safety instructions contained in these operating instructions and in the

instructions for use.

2. Check the rotor and all accessory parts for damages such as cracks, scratches or traces of corrosion.

3. Check the rotor chamber, the centrifuge spindle and the Auto-Lock of the rotor.

4. Check the rotor’s suitability using the chemical compatibility chart on on page-35.

Proper Loading

Contents

•“Before a Run” on page 9

•“Proper Loading” on page 9

•“Improper Loading” on page 10

•“Maximum Loading” on page 10

•“Lifetime” on page 10

Note You can also fully load the rotor. It is very important that the tubes are balanced against each

other.

3 Rotor Loading

Improper Loading

10 A27-6x50 Rotor Thermo Scientific

Improper Loading

Maximum Loading

The rotor can run at high speeds. The rotor design has sufficient reserve stability even when spinning at

top speed.

The safety system of the centrifuge requires that you do not overload the rotor.

There are two options available for centrifuging samples whose weight, including adapter, exceeds the

maximum permissible load:

•Reduce the fill level.

•Reduce the speed.

•Calculate the maximum speed with this formula and set the centrifuge at the calculated maximum

speed:

Lifetime

The lifetime of rotors and buckets is dependent on the amount of mechanical load. Do not exceed the

number of cycles recommended for rotors and buckets.

The maximum number of cycles for the rotor is given in the rotor table in section “Rotor Data” on

page 1.

The maximum number of cycles for buckets is marked on the buckets themselves.

Service Life Examples

nper = Permissible Speed

nmax = Maximum Speed

nper nmax

maximum permissible load

actual load

-----------------------------------------------------------------------

=

WARNING Replace the rotor when the specified number of cycles is reached. Due to the

mechanical load a rotor can break and thus damage the centrifuge.

Usage profile Maximum lifetime at 50,000 cycles

25 runs / day

200 days / year

10 years

Thermo Scientific A27-6x50 Rotor 11

4

Aerosol-tight Applications

Basic Principles

•Check that the sample containers are well suited for the desired centrifugation process.

Fill Level

Open top tubes are only to be filled to a level which ensures that the sample is unable to reach the top

of the tube during centrifugation. Therefore fill the tube only 2/3 of the rated level.

Checking the Aerosol-Tightness

The aerosol tightness testing of the rotors and buckets depend on the microbiological test process in

accordance with the EN 61010-2-020 Appendix AA.

Whether or not a rotor is aerosol-tight depends primarily on proper handling.

Check as needed to make sure your rotor is aerosol-tight.

The careful inspection of the seals and seal surfaces for signs of wear and damage such as cracks,

scratches and embrittlement is extremely important.

Aerosol-tight applications are not possible if the rotor is run without the lid.

Contents

•“Basic Principles” on page 11

•“Fill Level” on page 11

•“Checking the Aerosol-Tightness” on page 11

CAUTION Aerosol-tight rotors and tubes may only be opened in an approved safety

work-bench when centrifuging dangerous samples.

Mind the maximum permissible load.

CAUTION Be sure to check all sealings before starting any aerosol-tight applications.

4 Aerosol-tight Applications

Checking the Aerosol-Tightness

12 A27-6x50 Rotor Thermo Scientific

Aerosol-tightness requires the correct operation when filling the sample vessels and closing the rotor lid.

Quick Test

As a quick test, it is possible to test the aerosol-tightness of fixed-angle rotors using the following

process:

1. Lubricate all seals lightly.

Always use the special grease 76003500 when lubricating the seals.

2. Fill the cavities with approx. 10 ml of carbonated mineral water.

3. Close the rotor as explained in the handling instructions.

4. Shake the rotor vigorously using your hands.

This releases the carbonic acid gas which is bound in the water, resulting in excess pressure. Do not

apply pressure to the lid when doing so.

Leaks can be detected by escaping water or the sound of escaping gas.

Replace the seals if you detect any leaks. Then repeat the test.

5. Dry the rotor, rotor lid and the cover seal.

CAUTION Prior to each use, the seals in the rotor are to be inspected in order to assure that

they are correctly seated and are not worn or damaged.

Thermo Scientific A27-6x50 Rotor 13

5

Maintenance and Care

Cleaning Intervals

For the sake of personal, environmental, and material protection, it is your duty to clean and if

necessary disinfect the rotor on a regular basis.

Cleaning

Clean rotor and accessories as follows:

•Use warm water with a neutral solvent.

•Never use caustic cleaning agents such as soap suds, phosphoric acid, bleaching solutions or

scrubbing powder.

Contents

•“Cleaning Intervals” on page 13

•“Cleaning” on page 13

•“Disinfection” on page 16

•“Decontamination” on page 17

•“Autoclaving” on page 18

•“Service of Thermo Fisher Scientific” on page 18

Maintenance Recommended interval

Clean Rotor Chamber Daily or when soiled

Clean Rotor Daily or when soiled

Accessories Daily or when soiled

CAUTION Refrain from using any other cleaning or decontamination procedure than

those recommended here, if you are not entirely sure that the intended procedure is safe

for the equipment.

Use only approved cleansers.

If in doubt, contact Thermo Fisher Scientific.

5 Maintenance and Care

Cleaning

14 A27-6x50 Rotor Thermo Scientific

•Rinse the cavities out thoroughly.

•Use a soft brush without metal bristles to remove stubborn residue.

•Afterwards rinse with distilled water.

•Place the rotors on a plastic grate with their cavities pointing down.

•If drying boxes are used, the temperature must never exceed 50°C, since higher temperatures could

damage the material and shorten the lifetime of the parts.

•Use only disinfectants with a pH of 6-8.

•Dry aluminum parts off with a soft cloth.

•After cleaning, treat the entire surface of aluminum parts with corrosion protection oil

(70009824). Also treat the rotor cavities with oil.

•Store the aluminum parts at room temperature or in a cold-storage room with the cavities pointing

down.

Clean rotor and accessories as follows:

1. Open the centrifuge.

2. Turn off the centrifuge.

3. Release the rotor.

4. Grasp the rotor with both hands and lift it vertically off the centrifuge spindle.

5. Remove the centrifuge tubes and adapters.

6. Use a neutral cleaning agent with a pH value between 6 and 8 for cleaning.

7. Dry all of the rotors and accessories after cleaning with a cloth or in a warm air cabinet at a

maximum temperature of 50°C.

8. Store the rotor with its lid open.

•After cleaning, treat the entire surface of aluminum parts with corrosion protection oil

(70009824). Also treat the rotor cavities with oil.

•Grease the seal (76003500).

•Grease the thread in the lid (75003786).

CAUTION Before using any cleaning or decontamination methods except those

recommended by the manufacturer, users should check with the manufacturer that the

proposed method will not damage the equipment.

CAUTION When cleaning, do not allow liquids, especially organic solvents, to get on the

drive shaft or the bearings of the centrifuge.

Organic solvents break down the grease in the motor bearing. The drive shaft could freeze

up.

5 Maintenance and Care

Maintenance of O-Rings in Rotor Lid

Thermo Scientific A27-6x50 Rotor 15

Maintenance of O-Rings in Rotor Lid

In order to maintain the O-rings (red in the drawings) you have to disassemble the rotor lid.

In order to reach O-rings you need a retaining ring plier (65614, shipped with rotor).

1. Hold the rotor lid with the lid knob (1) in your palm and the thread pointing upwards.

2. Insert the retaining ring plier (65614) in the eyes of the retaining ring (5).

3. Close the retaining ring plier (65614) and lift the retaining ring over the thread.

4. In order to remove the O-ring (6) in the threads push the O-ring on two opposing side so it will

form a loop, which you then can use to remove the O-ring.

Note Check the O-ring when the rotor leaks and when autoclaving.

Note You can insert a paper-clip to the loop to lift the O-ring over the thread.

4

3

5

1

6

2

1

7

6

3

4

5

2

CAUTION Do not use any sharp items to remove the O-ring from the groove.

Page is loading ...

Thermo Fisher Scientific A27-6x50 Rotor User manual

Thermo Fisher Scientific A27-6x50 Rotor User manual

Related papers

Other documents