MULTIPLEX Drink Staging Platform Kit Owner Instruction Manual

Brand: MULTIPLEX

Model: Drink Staging Platform Kit

Type: Owner Instruction Manual

MULTIPLEX Drink Staging Platform Kit is a versatile and durable solution for mounting and organizing beverage dispensing equipment in commercial settings. Constructed from high-quality materials, it provides a stable and secure platform for drink staging, enhancing efficiency and optimizing workflow in busy beverage service areas. The kit includes all necessary components for easy installation, including a lidding platform, rear panel, and mounting hardware. It can be readily integrated with existing countertops, accommodating various dispensing tower configurations.

In accordance with our policy of continuous product development and improvement,

this information is subject to change at any time without notice.

EI213231 Revision 0 (JMT-KAK) 07-27-07

Manitowoc Beverage Equipment

2100 Future Drive  Sellersburg, IN 47172-1868

Tel: 812.246.7000, 800.367.4233  Fax: 812.246.9922

www.manitowocbeverage.com

Foodservice Group

Multiplex Beverage Equipment Installation Instructions for

Drink Staging Platform Kit

P.N. 00213231

Introduction

Before proceeding with the installation of the Drink Staging

Platform, check to see that the holes in the counter-top line

up with the mounting holes in the base of the Drink Staging

Platform (do not mount Drink Staging Platform at this time). If

holes do not line up, use the template provided with the Drink

Staging Platform to drill the required holes in the counter-

top. This also includes the 2" drain hole and the 4

/2" x 8"

rectangular cut-out for Syrup/Water lines and drain lines.

Caution: To Avoid Serious Injury

Important: Read the following warnings before beginning an

installation. Failure to do so may result in possible death or

serious injury.

DO Adhere to all National and Local Plumbing and Elec-

trical Safety Codes.

DO Turn “off” incoming electrical service switches

when servicing, installing, or repairing equipment.

DO Check that all flare fittings on the carbonation

tank(s) are tight. This check should be performed

with a wrench to ensure a quality seal.

DO Inspect pressure on Regulators before starting up

equipment.

DO Protect eyes when working around refrigerants.

DO Use caution when handling metal surface edges of

all equipment.

DO Handle CO

2 cylinders and gauges with care. Secure

cylinders properly against abrasion.

DO Store CO

2 cylinder(s) in well ventilated areas.

DO NOT Throw or drop a CO

2 cylinder. Secure the cylinder(s)

in an upright position with a chain.

DO NOT Connect the CO

2 cylinder(s) directly to the product

container. Doing so will result in an explosion caus-

ing possible death or injury. Best to connect the

2 cylinder(s) to a regulator(s).

DO NOT Store CO

2 cylinders in temperature above 125°F

(51.7°C) near furnaces, radiator or sources of heat.

DO NOT Release CO

2 gas from old cylinder.

DO NOT Touch Refrigeration lines inside units, some may

exceed temperatures of 200°F (93.3°C).

Notice: Water pipe connections and fixtures directly connected

to a potable water supply shall be sized, installed and

maintained in accordance with Federal, State, and Local codes.

Mounting the dispensing tower to the

drink staging platform kit

Note A: In most cases, the four (4) existing mounting holes to

the rear of the counter-top will line up with the base of the

Drink Staging Platform and should be used as a reference for

drilling the remaining holes.

Note B: The Drink Staging Platform can not be mounted to a

marine edge counter-top. Marine edge must be cut off before

drilling Drink Staging Platform holes in counter-top.

1. Attach elbow adapter and drain hose to dispensing tower

drain.

2. Attach Lidding Platform to Staging Platform Riser using

four (4)

/4"-20 x

/2" screws and nuts.

3. Apply bead of RTV sealant to bottom flange of dispensing

tower and position tower on Staging Platform. Align

three (3) holes in Lidding Platform with three (3) holes in

front flange of Dispensing Tower Drain Pan. Secure with

three (3)

/4"-20 x

/2" screws from bottom of Lidding Plat-

form.

4. Remove rear panel of Staging Platform and secure Dis-

pensing Tower at rear with

/4"-20 x

/2" screws and nuts

through rear flanges of Dispensing Tower and Staging Plat-

form.

Note: Dispensing Tower will overhang Staging Platform at sides

and rear.

5. Remove Splash Panel from Dispensing Tower and position

Staging Platform/ Dispensing Tower in position on counter.

Apply RTV sealant to bottom flange and secure Staging

Platform to counter with

/4"-20 x

/2" screws.

6. Route soda and syrup lines up through counter-top and

make connections to Dispensing Tower.

7. After checking for leaks, replace rear panel of Staging

Platform and Dispensing Tower Splash Panel. Install wire

drink rack in lower staging pan.

Completing the installation

The installation of the Drink Staging Platform is complete.

Refer to dispensing tower installation instructions provided

with unit to complete installation of dispensing tower.

EI213231 Revision 0 (JMT-KAK) 07-27-07

Equipment Installation Instructions

Installing the Dispensing Tower to the Drink Staging

Platform Kit (Figure 1)

Counter-top

Drink Staging

Platform

Dispensing

Tower

Rear Panel

Lidding

Platform

MULTIPLEX Drink Staging Platform Kit Owner Instruction Manual

MULTIPLEX Drink Staging Platform Kit Owner Instruction Manual

MULTIPLEX Drink Staging Platform Kit Owner Instruction Manual

Related papers

Other documents