MULTIPLEX Twenty Faucet Beer Station Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Twenty Faucet Beer Station
Type
Installation guide

MULTIPLEX Twenty Faucet Beer Station is designed for professional use in bars, restaurants, and other food service establishments. This versatile beer station boasts 20 faucets, allowing you to offer a wide variety of beers to your customers. The station is constructed from durable materials, ensuring longevity and reliability in demanding environments.

The MULTIPLEX Twenty Faucet Beer Station features a compact design that makes it suitable for spaces of all sizes. Its innovative design incorporates a support channel and side channels for easy installation and stability. This beer station is compatible with various beer kegs, providing you with the flexibility to dispense different types of beers.

MULTIPLEX Twenty Faucet Beer Station is designed for professional use in bars, restaurants, and other food service establishments. This versatile beer station boasts 20 faucets, allowing you to offer a wide variety of beers to your customers. The station is constructed from durable materials, ensuring longevity and reliability in demanding environments.

The MULTIPLEX Twenty Faucet Beer Station features a compact design that makes it suitable for spaces of all sizes. Its innovative design incorporates a support channel and side channels for easy installation and stability. This beer station is compatible with various beer kegs, providing you with the flexibility to dispense different types of beers.

In accordance with our policy of continuous product development and improvement,
this information is subject to change at any time without notice.
EI219196 Issued (JMT/KAK) 10 May, 2001
Manitowoc Beverage Equipment
2100 Future Drive Sellersburg, IN 47172-1868
Tel: 812.246.7000, 800.367.4233 Fax: 812.246.9922
www.manitowocbeverage.com
Foodservice Group
Multiplex Beverage Equipment Installation Instructions for
Twenty Faucet Beer Station (64" wide)
P.N. 00219196
1. Cut a 9
7
/8" (25.1 cm) x 60
1
/8" (152.7 cm) level opening
through the wall of the walk-in-cooler (refer to figure 1).
Bottom of opening is 1" (2.5 cm) above bottom of Beer
Faucet Plate.
2. Place a long support channel inside of the top of the open-
ing with 1" flange on the outside and a side channel to
each end of the opening. Install the side channels so the
short flanges of the side channels will be under and sup-
porting the long support channel. Attach to the inside wall
with screws provided (refer to figure 2).
3. Hang faucet plate by hooking over 1" flange of support
channel. Install the lower support channel.
Note: The lower support channel installs in the same manner
as the top channel except the channel will rest on top of the
short flanges of the side channels (refer to figure 3).
Figure 1
Figure 2
Support Channel
Side Channel
Figure 3
2
EI219196 Issued (JMT/KAK) 10 May, 2001
Equipment Installation Instructions
Caution: To Avoid Serious Injury
Important: Read the following warnings before beginning an installation. Failure to do so
may result in possible death or serious injury.
DO Adhere to all National and Local Plumbing and Electrical Safety Codes.
DO Turn “off” incoming electrical service switches when servicing, installing, or
repairing equipment.
DO Check that all flare fittings on the carbonation tank(s) are tight. This check
should be performed with a wrench to ensure a quality seal.
DO Inspect pressure on Regulators before starting up equipment.
DO Protect eyes when working around refrigerants.
DO Use caution when handling metal surface edges of all equipment.
DO Handle CO
2 cylinders and gauges with care. Secure cylinders properly against
abrasion.
DO Store CO2 cylinder(s) in well ventilated areas.
DO NOT Throw or drop a CO2 cylinder. Secure the cylinder(s) in an upright position
with a chain.
DO NOT Connect the CO2 cylinder(s) directly to the product container. Doing so will
result in an explosion causing possible death or injury. Best to connect the
CO2 cylinder(s) to a regulator(s).
DO NOT Store CO2 cylinders in temperature above 125°F (51.7°C) near furnaces,
radiator or sources of heat.
DO NOT Release CO2 gas from old cylinder.
DO NOT Touch Refrigeration lines inside units, some may exceed temperatures of
200°F (93.3°C).
Notice: Water pipe connections and fixtures directly connected to a potable water supply
shall be sized, installed and maintained in accordance with Federal, State, and Local codes.
  • Page 1 1
  • Page 2 2

MULTIPLEX Twenty Faucet Beer Station Installation guide

MULTIPLEX
Brand
MULTIPLEX
Model
Twenty Faucet Beer Station
Type
Installation guide

MULTIPLEX Twenty Faucet Beer Station is designed for professional use in bars, restaurants, and other food service establishments. This versatile beer station boasts 20 faucets, allowing you to offer a wide variety of beers to your customers. The station is constructed from durable materials, ensuring longevity and reliability in demanding environments.

The MULTIPLEX Twenty Faucet Beer Station features a compact design that makes it suitable for spaces of all sizes. Its innovative design incorporates a support channel and side channels for easy installation and stability. This beer station is compatible with various beer kegs, providing you with the flexibility to dispense different types of beers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents