Trane BMSC000AAA011000 Operating instructions

Brand: Trane

Model: BMSC000AAA011000

Type: Operating instructions

This manual is also suitable for

SAFETY WARNING

Only qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-

conditioning equipment can be hazardous and requires specific knowledge and training. Improperly installed, adjusted or altered equipment

by an unqualified person could result in death or serious injury.When working on the equipment, observe all precautions in the literature and

on the tags, stickers, and labels that are attached to the equipment.

Tracer

™

SC System Controller

Daily Operations

Guide

BAS-SVU025A-EN

November 2013

This document and the information in it are the property ofTrane and may not be used

or reproduced in whole or in part, without the written permission ofTrane.Trane reserves

the right to revise this publication at any time and to make changes to its content without

obligation to notify any person of such revision or change.

Trademarks

Trane and its logo are trademarks ofTrane in the United States and other countries. All

trademarks referenced in this document are the trademarks of their respective owners.

Warnings, Cautions, and Notices

Warnings, cautions, and notices are provided in appropriate places throughout this

document:

Revision History

New

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in

death or serious injury.

CAUTIONs

Indicates a potentially hazardous situation which, if not avoided, could result in

minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE:

Indicates a situation that could result in equipment or property-damage only

accidents.

Table of Contents

BAS-SVU025A-EN 3

Introduction ......................................................6

How to Use This Guide ........................................... 6

Additional Resources ............................................ 7

Product Overview .................................................8

Tracer SC Model Numbers ........................................ 8

Tracer SC Components ........................................... 8

Tracer SC Accessories ........................................... 9

Tracer SC Service Parts .......................................... 9

Licensing and Hardware ......................................... 11

Setup Requirements ............................................ 11

Navigating the User Interface .......................................12

Applying the Table Filter ........................................ 13

Using the Actions Button ........................................ 14

The Navigation Tree ..............................................15

Using the Navigation Tree ....................................... 15

Drag a Tracer SC Component onto the Tree ....................... 16

Drag a Tree Component onto the Home Button .................... 16

Drag Tree Nodes to Other Locations ............................. 16

Rename Tree Nodes ..........................................16

Editing the Navigation Tree ...................................... 17

Adding a Custom Graphics Node to the Tree ......................17

Editing a Node on the Tree ..................................... 17

Adding a Custom Folder to the Tree ............................. 17

Deleting a Node from the Tree .................................. 17

Undoing a Change to the Tree .................................. 17

Redoing a Previously Undone Change to the Tree .................17

Reseting the Tree to Standard Configuration ...................... 17

Viewing Help for the Navigation Tree ............................ 17

Alarms and Events Log ............................................18

Taking Action on an Alarm ....................................... 18

Event Classes .................................................. 18

Reports .........................................................20

Create a Report ................................................ 21

Export a Report ................................................ 21

Data Logs .......................................................22

Scheduled Data Logs ........................................... 23

Creating a Scheduled Data Log ................................. 23

Triggered Data Logs ............................................ 23

4 BAS-SVU025A-EN

Creating a Triggered Data Log .................................. 23

Spaces ..........................................................25

Space Status .................................................. 26

Equipment ......................................................27

Equipment Status .............................................. 28

Schedules .......................................................29

Optimal Start/Stop ............................................. 29

Creating a Schedule ............................................ 30

Exceptions and Calendars ....................................... 30

Points ..........................................................32

Point Types ................................................... 32

Point Overrides ..................................................34

Overriding a Point .............................................. 34

Using the Override Dialog Box ................................... 35

Systems ........................................................36

Area Application ............................................... 36

Variable Air Systems (VAS) Application ............................ 36

Chiller Plant Control (CPC) Application ............................. 36

Viewing System Status .......................................... 37

Tools ...........................................................38

Backup and Restore ............................................ 38

Custom Graphics ............................................... 39

Global Referencers ............................................. 39

Programs ..................................................... 39

System Logs .................................................. 39

Tracer ES IP Address ............................................ 39

Unit Controllers ..................................................40

Trane Unit Controllers Supported by the Tracer SC .................. 40

Non-Trane Unit Controllers Supported by Tracer SC ................. 40

LEDs and the 7-Segment Display ....................................41

Powering Up/Powering Down the Tracer SC ........................ 41

The LEDs and the 7-Segment Display .............................. 41

Interpreting the LEDs ......................................... 42

Interpreting the 7-Segment Display .............................. 43

Troubleshooting ..................................................44

BAS-SVU025A-EN 5

Troubleshooting with LEDs and the 7-Segment Display ............... 44

Force Return to Factory Defaults .................................. 44

Troubleshooting Network Connections ............................ 45

PING ....................................................... 45

IPCONFIG ................................................... 45

Web Browser Security Settings ................................. 45

6 BAS-SVU025A-EN

Introduction

TheTracer SC Daily Operations Guide provides information and instructions for tasks that daily

operators typically perform in aTrane BAS using theTracer SC System Controller, such as

managing alarms and events, overriding setpoints, and running reports.

The following information is provided in this document:

• Product overview (hardware, model numbers, licensing)

• Navigating theTracer SC user interface, performing daily operator BAS tasks

• Interpreting the LEDs and 7-segment display, troubleshooting

This guide does not cover programming and configuration. For more information on advanced

user tasks, refer to theTracer SC System Controller Installation and Setup Guide, BAS-SVX31-EN,

or access theTracer SC Help by clicking the help icon located on the global navigation bar.

How to Use This Guide

Although it is best practice to familiarize yourself with all aspects ofTracer SC, it is not necessary

to read this guide in any particular order or in its entirety.To quickly locate a specific task or topic,

simply refer to theTable of Contents on page 3.

The sections in this guide that describeTracer SC applications will begin with an overview of the

application (Alarms, Reports, for example) and an accompanying figure that shows the application

highlighted on the left-hand navigation bar (see Figure 1).

Note: If you are reading a copy of this document that was translated from English, please note that

all figures and illustrations in this guide are for navigational purposes only.The data and

text depicted is not relevant to the accompanying instructions.

Figure 1. Example of navigational elements

The application

currently in view is

highlighted on the

left-hand navigation

bar.

BAS-SVU025A-EN 7

Introduction

Additional Resources

Following is a list of relatedTracer SC documentation and training resources.

Tracer™ SC System Controller Installation and Setup Guide (BAS-SVX31-EN)

Describes detailed configuration for network settings, Ethernet network wiring, and IT security.

Tracer™ SC System Controller Installation Sheet (X39641154-01)

For mounting the enclosure and providing AC power.

Tracer™ SC online help

An online help system is included with theTracer SC user interface. Global help has a table of

contents and is searchable. Contextual help is specific to the information on each page.

Tracer™ BAS Operator Suite (Mobile App) Getting Started Guide

(BAS-SVU23-EN)

Describes how to obtain, download, install, and set up the mobile app.

BACnet

MS/TP Wiring Best Practices and Troubleshooting (BAS-SVX051-EN)

Provides best practices, procedures, and troubleshooting for wiring BACnet unit controllers to a

Tracer SC system controller.

Tracer™ SC Air Systems Application Guide (BAS-APG007-EN)

Describes variable-air-volume strategies for variable air systems. It also include constant-volume

applications and area application strategies forTracer SC.

Tracer™ Graphical Programming (TGP2) Application Guide (BAS-APG008-EN)

Describes how to use theTGP2 editor and typical implementation strategies and best practices for

usingTGP2.

Tracer™TU Service Tool Getting Started Guide (TTU-SVN01-EN)

This document describes how to use theTracerTU service tool to

• Transfer programs to the Tracer SC

• Start theTracer Graphical Programming (TGP2) Editor and theTracer Graphics Editor from

withinTracerTU

• Backing up and restoring firmware andTGP2 programs

Trane College of Building Automation

TheTrane College of Building Automation (TCBA) offers a comprehensive portfolio of technical

courses to help you effectively monitor and coordinate your HVAC equipment and systems.

http://www.trane.com/Commercial/DNA/view.aspx?i=586

8 BAS-SVU025A-EN

Product Overview

TheTracer™ SC system controller (Tracer SC) serves as the central coordinator for all individual

equipment devices on aTracer building automation system.TheWeb-based interface of theTracer

SC system controller provides an easy and convenient way for building operators to access their

building automation system. Access is available from most PCs, tablets and smartphones that

meet system requirements.

Tracer SC Model Numbers

Tracer SC Components

TheTracer SC is equipped with the components shown in Figure 1.

Model number Description

BMSC000AAA011000 (current) Tracer SC with power supply module (PM014) with U.S. outlet, enclosure ordered separately

BMSC000AAA011100 (obsolete) Tracer SC system controller with power supply module (PM214) with U.S. outlet, in enclosure

BMSC000AAA011200 (obsolete) Tracer SC system controller with power supply module (PM214), in enclosure

Figure 1. Tracer SC components

IMC

BACnet

MS/TP LINK 1

BACnet

MS/TP LINK 2

USB service

tool port

SD card port (future)

EIA-232 serial connection

USB host (future)

Ethernet network connection 2 (supports

TCP/IP) (recommended for direct

connection to PC)

Ethernet network connection 1 (supports

BACnet and TCP/IP (recommended for

building network connection)

Power button

Status LED

7-segment display

Rotary switches

LonTalk service pin

LonTalk

BACnet LEDs

Ethernet LEDs

LonTalk LEDs

LonTalk service LED

IMC LEDs

EIA-232 LEDs

BAS-SVU025A-EN 9

Product Overview

Tracer SC Accessories

Tracer SC Service Parts

The service parts listed in Table 1 and Table 2 are available for theTracer SC.The numbers in the

tables correspond to those in Figure 2.

Note: Some of the service parts are the same for all models.

Description Order number

BACnet terminator 2 pack

(a)

(a)For information about this accessory, see BACnet MS/TP Wiring Best Practices (BAS-SVX051-EN).

X1365152401

Rover LonTalk interface adaptor

(b)

(b)For information about this accessory, see Rover Service Tool Installation, Operation, and Programming (EMTX-SVX01).

S3090062062

Table 1. Tracer SC model BMSC0 00AAA011000 (current)

Number in

Figure 2 Description Order number

1 Enclosure for DIN-mounted controllers (120 VAC, with outlet) X13651559010

2 Tracer SC module S3090058462

3 Power supply module X1365153801

(not shown) Enclosure for DIN-mounted controllers (230 VAC, no outlet) X13651560010

(not shown) Transformer service part S3090062462

4 IMC power cable S3090059562

(not shown)

Large enclosure for DIN-mounted controllers, 120 VAC, with outlet

(solid door)

X13651552-01

(not shown)

Large enclosure for DIN-mounted controllers, 120 VAC, with outlet

(display-capable door)

X13651553-01

(not shown)

Large enclosure for DIN-mounted controllers, 230 VAC, with outlet

(display-capable door)

X13651554-01

(not shown)

Large enclosure for DIN-mounted controllers, 230

VAC, with outlet (display-capable door)

X13651555-01

Table 2. Tracer SC models BMSC000AAA011100 and BMSC000AAA011200 (obsolete)

Number in

Figure 2 Description Order number

2 Tracer SC module S3090058462

3 Power supply module S3090058562

4 IMC power cable S3090059562

5 Cable assembly/modular terminal kit with U.S. outlet S3090059062

(not shown) Cable assembly/modular terminal kit S3090059162

6 Control panel cover (for models with U.S. outlet) S3090058962

(not shown) Control panel cover S3090058862

7 Enclosure S3090058762

10 BAS-SVU025A-EN

Product Overview

Figure 2. Service parts for the Tracer SC

BAS-SVU025A-EN 11

Product Overview

Licensing and Hardware

The number of devices that are supported is limited by the number within the application license.

The maximum amount is 240 devices in a single license. As ofTracer SC version 3.0, allTracer SCs

ship with a base license installed.The order number for an SC Application license is

BMCF000AAA0AE00 (15 devices).

To utilize the expanded communications functionality for multi-SC facilities, the following are

required:

• OneTracer SC with an Application license

• One or moreTracer SCs with a Base license

Setup Requirements

The following are required for setup and normal operation:

Scenario 1: Single SC Facility

• Tracer SC must have an application license in order to install equipment and facilitate control.

• Ethernet port 1 must be used for communication over BACnet/IP.

• BACnet MS/TP port network number cannot exceed 4193.

Scenario 2: Multi-SC Facility

• OneTracer SC must have an application license in order to install equipment and facilitate

control.

• AdditionalTracer SCs do not require a license.

• Ethernet port 1 must be used for communication between multiple SCs over BACnet/IP

• Tracer SC Device IDs must be unique.

• BACnet MS/TP port network number cannot exceed 4193.

• Tracer SCs on separate subnets must have one BBMD per subnet.

• UDP ports must be the same across all SCs in the facility.

Note: Both theTracer SC-App and theTracer SC-Base must be configured to communicate to each

other over BACnet/IP.They can reside on the same network subnet or on a separate subnet.

Scenario 3: Trane Intelligent Services (TIS)

• No additional license required;Tracer SC isTIS-Ready out of the box.

• ConfigureTracer SC Ethernet port 1 or 2 to communicate to the Internet.

• TIS must be enabled.

For more information about Trane Intelligent Services, see “TIS Technical Specifications”,

SRV-PRC011-EN.

License Type TIS Ready Multi SC Ready BAS App

Base Up to 5 devices Yes N/A

Application Up to 120 devices Yes Up to 240 devices

12 BAS-SVU025A-EN

Navigating the User Interface

TheTracer SC user interface (UI) is designed with common navigation elements across all pages.

These include the global navigation bar, the left navigation menu, contextual help, and the

navigation tree. Each of these elements is described below.

Global navigation bar

Contains shortcuts to the home page, alarm and event log, user preferences, administrative

functions, the “Configuration UI”, and the entireTracer SC help system.

Outdoor air conditions

This information area displays the current outdoor air temperature outside of your facility.

Context sensitive help

Click to open a help topic exclusi ve to the page in which you are viewing.

Printer icon

Click to print the page that you are viewing.

The Screen Expansion icon

click to temporarily hide the left navigation menu.To return to the default view, click the icon again.

Left navigation menu

Contains a list ofTracer SC applications and equipment.

Figure 1. Navigational elements on the Tracer SC user interface

BAS-SVU025A-EN 13

Navigating the User Interface

The navigation tree

This component contains the logically ordered and grouped content of all the elements of your

HVAC system. It is a complex component that is built dynamically based on a number of variables

and dependencies related to the configuration of a facility, the content of the HVAC, and other

systems operating in the facility. For more information, see “The NavigationTree,” p. 15.

Applying the Table Filter

Table filtering allows you to see only selected data by setting up rules and conditions.The option

to filter tables is available on the following pages:

• Alarms and Events

• Data Logs

• Reports

• Spaces

• Area, VAS, Chiller Plant (AlarmsTab)

To apply a table filter:

1. From one of the above mentioned pages, click the filter icon.The Filter dialog box appears.

2. From the Column drop-down

list, select a column on which to base your filter.

3. From the Condition drop-down

list, select a condition.

4. In the V

alue field, enter a value that the selected Column and Condition will filter.

5. Click Filter.The table displays results based on the applied filter.

6. Click the

button to add a rule. Up to three rules can be added to a filter.

7. Use the Matc

h drop-down list to include all rules or any rules.

To remove the filter, click Clear filter located directly above the first entry in the table on the page

you are viewing.

Example filter for Data Logs

Column = created by

Condition = is

Value = Area

Results:The above filter will only display data logs that were created by Area.

14 BAS-SVU025A-EN

Navigating the User Interface

Using the Actions Button

The actions button is available onTracer SC pages in which certain actions can be

taken on selected items.

To delete a report (example):

1. Select a report from the Reports page.

2. Click the actions button and then select delete saved report.

Figure 2. Using the actions button

Actions button

Selected item

BAS-SVU025A-EN 15

The Navigation Tree

The navigation tree contains the logically ordered and grouped content of all the elements of your

HVAC system.The navigation tree populates automatically when spaces, systems, points, and

equipment are installed.

Using the Navigation Tree

Click the arrow icon on the navigation tree to expand the tree and display the contents (Figure 1).

The navigation tree can be customized according to your preferences and facility needs.The tree

must be unlocked before any editing can be done. Click the chain link icon located at the bottom

of the tree. when clicked, the edit bar appears which contains a number of edit icons.

Note: The tree must be unlocked before any changes can be made. Click the chain link icon

located at the bottom of the tree to enable editing.To save edits made to the navigation

tree, lock the tree by clicking the chain link icon.

Figure 1. Expanding the navigation tree

Click the arrow

icon to expand

the tree

Edit bar

16 BAS-SVU025A-EN

The Navigation Tree

Drag a Tracer SC Component onto the Tree

You can create nodes on the tree by dragging them from the title of a component onto the tree, as

shown in Figure 2. Click and drag a component from theTracer SC page onto the tree. An image

representing the component appears red, then green when it is dragged over a valid area.

Depending on where you locate the dropped image, the new node will appear under the node you

drop it onto.To save your changes, lock the navigation tree by clicking the chain link icon.

Drag a Tree Component onto the Home Button

Click and drag a component from the tree as shown below, or from the title of anTracer SC

component on the page to the Home button.To save your changes, lock the navigation tree by

clicking the chain link icon.

Drag Tree Nodes to Other Locations

Nodes can be dragged and dropped to other locations on the tree. When a node is dropped onto

another node that is currently not a folder, the node icon will then appear as a folder icon. Multiple

nodes can be selected at the same time by clicking on multiple nodes.To save your changes, lock

the navigation tree by clicking the chain link icon.

Rename Tree Nodes

Nodes on the tree can be renamed directly within the tree. Rename a node by “slow” clicking on

the tree node while in unlocked mode. Slow is defined as two clicks on the same node spaced

between 1 and 5 seconds apart. This places the name of the node in edit mode, in which the old

name can be deleted and the new one entered.To save your changes, lock the navigation tree by

clicking the chain link icon.

Figure 2. Creating nodes

Figure 3. Dragging components from the tree

BAS-SVU025A-EN 17

The Navigation Tree

Editing the Navigation Tree

The navigation tree can be customized according to your preferences and facility needs.The tree

must be unlocked before any editing can be done.

Adding a Custom Graphics Node to the Tree

1. Click the custom graphics icon located on the navigation tree edit bar.The Add a Custom

Graphics Node to the Tree dialog

box appears.

2. Select a graphic from list. (A filtering option is available for your convenience).

3. Click next.

If the graphic is associated with a template, a tree with all the devices on the SC is displayed.

ou can then select the equipment with which to associate the graphic. If the graphic is not

associated with a template, a pane with the ability to save the graphic is displayed.

4. Save the graphic (template or otherwise).

Editing a Node on the Tree

1. Click to select one or more nodes on the tree.

2. Click the edit node icon

located on the navigation tree edit bar.The Edit Nodes dialog box

appears.

3. Select an action: Modify custom graphic assignment, or Reset custom node labels to default.

4. Follow the instructions in the dialog box to complete the action.

Adding a Custom Folder to the Tree

1. Click the add folder icon located on the edit bar. A new folder appears at the bottom of the

tree, or below a selected node.

2. Click once on the folder to place in edit mode, then rename the folder.

Deleting a Node from the Tree

1. Select a node or folder on the tree (text displays in bold when properly selected).

2. Click the delete icon

located on the navigation tree edit bar.

The selected item is deleted.

Undoing a Change to the Tree

While editing the tree, you can undo a change by clicking on the undo icon . Actions can be

undone back to the point where the tree was unlocked for editing.The undo icon will be active only

when there are actions that can be undone.

Redoing a Previously Undone Change to the Tree

While editing the tree, you can redo a previously undone change by clicking on the redo icon

. The redo stack is cleared once a new operation is performed.The redo icon will be active only

when there are actions that can be redone.

Reseting the Tree to Standard Configuration

You can reset the tree to its standard configuration by clicking on the eraser icon

Viewing Help for the Navigation Tree

Click the help icon to view help topics pertaining to the navigation tree.

18 BAS-SVU025A-EN

Alarms and Events Log

The alarm handling capabilities ofTracer SC allow users to recei ve, view, acknowledge, and make

comments on building alarms and events.

The Alarms and Events page (Figure 1) contains a list of alarms and events that have been detected

by the system. Data displayed in the log includes when and where the event occurred and whether

operator acknowledgment is required.

To apply a filter to the table, see “Applying theTable Filter,” p. 13.

Taking Action on an Alarm

1. Click inside each row to select an alarm. Selected rows will be highlighted.

2. Click the actions button to refresh, add or view comments, acknowledge a comment, export the

alarm log, or delete all from the log.

Event Classes

Events can be assigned one of four severities.The severity icon appears in the severity column on

the Alarms and Events page.The severity column provides a way to sort the log according to the

severity of events and alarms.

Information

Events that require tracking but are not defined as alarms. Examples include the notification that

a lighting system will soon be activated, or a user logging on to the system.

Figure 1. Alarms and Events page

BAS-SVU025A-EN 19

Alarms and Events Log

Advisory

Alarms that do not affect the operation of the system but may be of concern to a user. Examples

include custom system control events or a user override of system equipment.

Service Required

Alarms that require the attention of service personnel.These might include dirty filter notifications

or sensor failures.

Critical

These alarms require the immediate attention of service personnel. Critical alarms indicate a major

failure of equipment that might result in property damage or excessive tenant comfort issues.

Examples may include compressor failures or an emergency shutdown.

20 BAS-SVU025A-EN

Reports

Reports provide useful information that can be used to make decisions about building operations.

TheTracer SC Reports page contains two tabs: Saved Reports and Scheduled Reports.

You can generate the following types of standard reports for Trane equipment:

• Site reports

• VAS commissioning reports

• Points reports

• Chiller reports

Reporting features include:

• Creating scheduled reports

• Scheduling reports to run during a specific date and time

• Specifying file storage options for scheduled reports

• Exporting reports to save onto your PC as CSV, HTML, or PDF files

To apply a filter to the table, see “Applying theTable Filter,” p. 13.

Figure 1. Reports page

Page is loading ...

Trane BMSC000AAA011000 Operating instructions

Brand: Trane

Model: BMSC000AAA011000

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Trane BMSC000AAA011000 Operating instructions

This manual is also suitable for

Trane BMSC000AAA011000 Operating instructions

Related papers

Other documents