Not for
Reproduction
Not for
Reproduction
Table of Contents:
Products Covered by this Manual.......................................3
General Information..............................................................4
Operator Safety.....................................................................4
Safety Rules and Information...........................................4
Safety Decals....................................................................5
Safety Icons......................................................................5
Installation.............................................................................5
Remove the Carburetor Shield.........................................5
Install the Collector Mount Plate.......................................5
Install the Collector Mount Posts......................................9
Install the Collector Hood Frame....................................10
Install the Collector Hood................................................10
Install the Collector Inlet.................................................11
Install the Collector Hood Latch......................................11
Install the Grass Collection Bags....................................11
Install the Discharge Tube..............................................12
Install the Weights and Weight Mounts..........................12
Operation.............................................................................14
General Operating Instructions.......................................14
Opening and Closing the Collector Hood.......................15
Troubleshooting..................................................................15
Troubleshooting Charts..................................................15
Unplugging a Clogged Unit.............................................16
Collector System Removal.................................................17
2 ferrismowers.com | snapperpro.com
Not for
Reproduction
Products Covered by this Manual
TURBO-Pro Blower w/ 2-Bag Hard Top Collection System (10 cubic feet)
s/n: 2016497836 & above44"IS600Z5600777
s/n: 2016497836 & above48"IS600Z5600778
s/n: all48"F160Z5600779
s/n: 2016497836 & above48"S50XT, S150XT
s/n: 2016497836 & above52"IS700Z, F160Z, S125XT,
S150XT
5600780
s/n: 2016497836 & above52"IS2100Z5600781
TURBO-Pro Blower w/ 3-Bag Hard Top Collection System (15 cubic feet)
s/n: 2016497836 & above52"IS2100Z5600782
s/n: 2016497836 & above52"IS700Z, F160Z, S125XT,
S150XT
5600783
s/n: 2016497836 & above61"IS700Z, S125XT5600784
TURBO-Pro MAX Blower w/ 3-Bag Hard Top Collection System (15 cubic feet)
s/n: 2016497836 & above52"IS2100Z5600785
s/n: all52"F160Z5600786
s/n: 2016497836 & above52"S150XT
s/n: 2016497836 & above61"IS2100Z, F210Z, S200XT5600787
s/n: 2016497836 & above61"IS3100Z5600788
s/n: all61"IS3200Z, F320Z5600862
FAST-Vac® Blower w/ 3-Bag Hard Top Collection System (15 cubic feet)
s/n: 2016497836 & above52"IS700Z, F160Z, S125XT,
S150XT
5600789
s/n: 2016497836 & above52"IS2100Z5600790
s/n: 2016497836 & above61"IS700Z, F210Z, IS2100Z,
S125XT, S200XT
5600791
s/n: 2016497836 & above61"IS2500Z5600792
s/n: 2016497836 & above61"IS3100Z5600793
s/n: all61"IS3200Z, F320Z5600863
3
Not for
Reproduction
General Information
Thank you for purchasing this quality-built grass collection
system. When operated and maintained according to the
instructions in this manual, your grass collection system will
provide you many years of dependable service.
This manual contains safety information to make you aware of
the hazards and risks associated with this product and how to
avoid them. This product is designed and intended to be used
and maintained according to the manual for grass collection
from established lawns and is not intended for any other
purpose. It is important that you read and understand these
instructions thoroughly before attempting to operate this
equipment. Save these original instructions for future
reference.
These setup instructions are to be done in addition to the Blower
and Blower Mount installation instructions detailed in the
blower's operators manual included with the blower mount.
You must observe and obey all safety instructions in the blower's
operator's manual along with all instructions detailed in this
manual.
The images in this document are representative, and are meant
to compliment the instructional copy they accompany. Your unit
may vary from the images displayed.
LEFT
and
RIGHT
are as
seen from the operator's position.
Date of
Purchase:
Copyright © Briggs & Stratton Corporation, Milwaukee, WI, USA.
All rights reserved.
FERRIS is a trademark of Briggs & Stratton Corporation,
Milwaukee, WI, USA.
SNAPPER PRO is a trademark of Briggs & Stratton Corporation,
Milwaukee, WI, USA.
Briggs & Stratton Power Products Group, LLC.
5375 N. Main Street
Munnsville, NY 13409-4003
(800) 933-6175
ferrismowers.com | snapperpro.com
Operator Safety
In addition to all of the safety instructions described in this
manual, you must obey all the safety instructions in the blower's
operators manual included with the blower mount.
Safety Rules and Information
Read these safety instructions and follow them closely. Failure
to obey these rules could result in loss of control of unit, severe
personal injury or death to you, or bystanders, or damage to
property or equipment.
This mowing deck is capable of amputating hands and feet
and throwing objects.
The triangle in text signifies important cautions or warning
which must be followed.
WARNING
• Check the collection system to make sure it is bolted
tightly to the rider.
WARNING
• When blower assembly is removed from the mower deck,
the deflector must be properly installed.
WARNING
Amputation and thrown objects hazard
If the mower stalls or the turbo blower chute plugs:
1. Disengage the blower (blades) and remove the ignition
key and wait for all parts to stop before disconnecting or
unlatching any parts attached to the blower or the
collection system.
2. Remove the foreign object or clear the chute with a
suitable tool, such as a broom handle, before restarting
the engine. NEVER place hands into the blower housing
to clear jammed objects. Blower may rotate when object
is removed.
WARNING
For added rider stability and to prevent tipping or loss of
control:
• Use reduced speed on uneven ground and when turning
corners.
• Reduce loads on hillsides. It is recommended that the
collection system be kept no more than half full when
negotiating any slopes. Start mowing on slopes when the
collection system is empty.
NOTICE
• Collector bags are subject to deterioration and wear during
normal use. Inspect the bag periodically for tears, holes,
or weak spots, and replace with a new bag that meets the
manufacturer's durability standards.
4 ferrismowers.com | snapperpro.com
Not for
Reproduction
Safety Decals
Before operating your unit, read the safety decals. The cautions
and warnings are for your safety. To avoid a personal injury or
damage to the unit, understand and follow all the safety decals.
WARNING
If any safety decals become worn or damaged and cannot be
read, order replacement decals from your dealer.
Part Number: 5104315 - Decal, Container, IconsA.
Safety Icons
Warning - Thrown objects hazard:
• Do not open collection system container with engine
running.
• Do not operate with blower or collection system tube
unlatched or missing.
• Operate only with both the entire collection system and front
counterbalance weights installed and the collection system
closed and latched.
Warning - Loss of traction and control hazard:
• Do not operate with only the collection system installed.
• Do not operate with only the front counter balance weights
installed.
• Operate only with both the entire collection system and front
counter balance weights installed and the collection system
closed and latched.
Installation
In addition to these installation instructions, perform the
installation instructions for the blower and blower mount that
are detailed in the blower's operators manual included with the
blower mount.
Remove the Carburetor Shield
If a unit has a carburetor shield and a three bag collection
system is going to be installed on the unit, the carburetor shield
must be removed first.
1. If the engine is hot, allow sufficient time for the muffler to
cool to prevent a burn injury during installation process.
2. Remove the carburetor shield (A, Figure 1) from the top of
the rear bumper (B) by removing the hardware (C, D & E)
securing the shield to the bumper.
1
Install the Collector Mount Plate
There is a different collector mount plate for a 2-bag collection
system and a 3-bag collection system. For all 2-bag collection
system installations on units with 52" mower decks, the collector
mount plate must be offset to allow for proper discharge tube
alignment. Refer to the correct instructions for your setup.
5
Not for
Reproduction
Install the 2-Bag Collector Mount Plate on a
Round Tube Bumper (44" & 48" Mower Deck)
2
1. Position the collector mount (A, Figure 2) onto the bumper
(B) and install a U-bolt (C) over the center tube and through
the center slots identified as "A" in Figure 3 and loosely
install two 3/8 nylock flange nuts (D).
3
2. On the left side of the bumper install a U-bolt over the top
tube and through the slots identified as "B" in Figure 3 and
then through a mounting plate (E, Figure 2) and loosely
install two 3/8 nylock flange nuts.
3. On the right side of the bumper install a U-bolt over the top
tube and through the slots identified as "C" in Figure 3 and
then through a mounting plate (E, Figure 2) and loosely
install two 3/8 nylock flange nuts.
4. Center the collector mount on the bumper. The hardware
will be tightened later.
Install the 2-Bag Collector Mount Plate on a
Round Tube Bumper (52" Mower Deck)
4
1. Position the collector mount (A, Figure 4) onto the bumper
(B) and install a U-bolt (C) over the center tube and through
the center slots as identified as "A" in Figure 5 and loosely
install two 3/8 nylock flange nuts (D).
5
2. On the left side of the bumper install a U-bolt over the top
tube and through the slots identified as "B" in Figure 5 and
then through a mounting plate (E, Figure 4) and loosely
install two 3/8 nylock flange nuts.
3. On the right side of the bumper, install a U-bolt over the top
tube and through the slots identified as "C" in Figure 5 and
secure with two 3/8 nylock flange nuts.
4. Route two 3/8 X 1" bolts (F, Figure 4) and 3/8 flat washers
(G) through the holes identified as "D" in Figure 5 in the
collector mount plate and then through a mounting plate
and then loosely install two 3/8 nylock flange nuts.
5. Slide the collector mounting plate as far towards the right
side of the machine as possible. The hardware will be
tightened later.
6 ferrismowers.com | snapperpro.com
Not for
Reproduction
Install the 2-Bag Collector Mount Plate on a Flat
Plate Bumper (48" Mower Deck)
6
1. Position the collector mount plate (A, Figure 6) onto the
bumper (B) and route a 3/8" X 1" bolt (C) and 3/8 flat washer
(D) through the hole identified as "A" in Figure 7 and then
through the bumper and then secure with a 3/8 nylock flange
nut (E).
7
2. On the left side of the bumper, route two 3/8 X 1" bolts and
3/8 flat washers through the mount plate (F, Figure 6), the
holes identified as "B" in Figure 7 and then through the
bumper and then secure with two 3/8 nylock flange nuts.
3. On the right side of the bumper, route two 3/8 X 1" bolts
and 3/8 flat washers through the mount plate, the holes
identified as "C" in Figure 7 and then through the bumper
and then secure with two 3/8 nylock flange nuts.
4. The hardware will be tightened later.
Install the 2-Bag Collector Mount Plate on a Flat
Plate Bumper (52" Mower Deck)
1. Position the mount plate (A, Figure 8) on the inside of the
bumper (B) and secure the left hand side of it in place by
routing two 3/8 X 1" bolts (C) and 3/8 flat washers (D)
through the furthest left holes in the bumper, the left side
of the mount plate and loosely install two 3/8 nylock flange
nuts (E).
8
2. Position the collector mount plate (F) onto the bumper and
install a 3/8 X 1" and a 3/8 flat washer through the hole
identified as "A" in Figure 9 and loosely install a 3/8 nylock
flange nut.
9
3. Install two 3/8 X 1" bolts and 3/8 flat washers through the
holes identified as "B" in Figure 9 and loosely install two
3/8 nylock flange nuts .
4. Route two 3/8" X 1-1/4" bolts (G, Figure 8) and 3/8 flat
washers through a mounting plate (H), the holes identified
as "C" in Figure 9 and then through the bumper and loosely
install two 3/8 nylock flange nuts.
5. Route two 3/8" X 1" bolts and 3/8 flat washers through a
mounting plate, the holes identified as "D" in Figure 9 and
loosely install two 3/8 nylock flange nuts.
6. The hardware will be tightened later.
7
Not for
Reproduction
Install the 3-Bag Collector Mount Plate on a
Round Tube Bumper (61" Mower Deck)
10
1. Position the collector mount (A, Figure 10) onto the bumper
(B) and install a U-bolt (C) over the center tube and through
the center slots as identified as "A" in Figure 11 and loosely
install two 3/8 nylock flange nuts (D).
11
2. On the left side of the bumper install a U-bolt over the top
tube and through the slots identified as "B" in Figure 11 and
then through a mounting plate (E , Figure 10) and loosely
install two 3/8 nylock flange nuts.
3. On the right side of the bumper install a U-bolt over the top
tube and through the slots identified as "C" in Figure 11 and
then through a mounting plate and loosely install two 3/8
nylock flange nuts.
4. Center the collector mount. The hardware will be tightened
later.
Install the 3-Bag Collector Mount Plate on a
Round Tube Bumper (IS3200Z & F320Z w/ 61"
Mower Deck)
12
1. Position the collector mount (A, Figure 12) onto the bumper
(B) and install a U-bolt (C) over the second tube down from
the top of the bumper and through the center slots as
identified as "A" in Figure 13 and loosely install two 3/8
nylock flange nuts (D).
13
2. On the left side of the bumper install a U-bolt over the top
tube and through the slots identified as "B" in Figure 13 and
then through a mounting plate (E , Figure 12) and loosely
install two 3/8 nylock flange nuts.
3. On the right side of the bumper install a U-bolt over the top
tube and through the slots identified as "C" in Figure 13 and
then through a mounting plate and loosely install two 3/8
nylock flange nuts.
4. Center the collector mount. The hardware will be tightened
later.
8 ferrismowers.com | snapperpro.com
Not for
Reproduction
Install the 3-Bag Collector Mount Plate on a
Round Tube Bumper (IS3100Z w/ 61" Mower Deck)
1. Install the collector mount plate (A, Figure 14) on to the
bumper (B). Install two of the 3/8 U-bolts (C) over the top
bumper tube and through the collector mount plate and
loosely secure with four 3/8-16 nylock flange nuts (D).
14
2. Install the remaining 3/8 U-bolt over the third tube down
from the top of the bumper and loosely secure with two
3/8-16 nylock flange nuts.
3. Center the collector mount plate on the bumper and tighten
all the hardware securely.
Install the 3-Bag Collector Mount Plate on a Flat
Plate Bumper (61" Mower Deck)
15
1. Position the collector mount plate (A, Figure 15) onto the
bumper (B) and install two 3/8 X 1" bolts (C) and flat
washers (D) through the holes identified as "A" in Figure
16 and loosely install two 3/8 nylock flange nuts (E).
16
2. On the left side of the bumper route two 3/8" X 1" bolts and
3/8 flat washers through the bumper, through the holes in
the collector plate identified as "B" in Figure 16, a mounting
plate (F, Figure 15), and loosely install two 3/8 nylock flange
nuts.
3. On the right side of the bumper route two 3/8" X 1" bolts
and 3/8 flat washers through the bumper, through the holes
in the collector plate identified as "C" in Figure 16, a
mounting plate, and loosely install two 3/8 nylock flange
nuts.
4. The hardware will be tightened later.
Install the Collector Mount Posts
1. Position the collector mount posts (A, Figure 17) onto the
collector mount plate so that the small upper tubes face
towards the center of the machine as seen in Figure 17 and
secure them using the hitch pins with lanyards (C).
9
Not for
Reproduction
17
2. Secure the hitch pins in place with their attached cotter pins
(D).
3. Position the mounting plates (B) as necessary to align the
holes between the collector mount plate and mounting plates
and then tighten all hardware installed in the
Install the
Collector Mount Plate
procedures. This will insure that the
holes are properly aligned for easy installation and removal.
Note:
Step #3 is not necessary for installation on IS3100Z
models since the mounting plate is stationary.
Install the Collector Hood Frame
1. Install the collector hood frame (A, Figure 18) onto the
collector mount posts (B) and secure by installing two 1/2
X 2-1/2" bolts (C) and two 1/2 flat washers (D) through the
collector hood frame, the collector mount posts, and then
securing with two 1/2 nylock flange nuts (E). The hardware
is routed so that it faces towards the center of the unit.
18
Install the Collector Hood
1. Position the collector hood (B, Figure 19) on the collector
hood frame (A).
19
10 ferrismowers.com | snapperpro.com
Not for
Reproduction
2. Route a 5/16 X 2-1/2" bolt (C) through the collector hood
and the collector hood frame and a 5/16 flat washer (D) and
secure with a 5/16 nylock flange nut (E). Repeat this process
for the other side of the collector hood. The hardware should
be oriented so that it faces towards the center of the unit.
Install the Collector Inlet
1. If the you are installing a 3-bag collection system, the
collector inlet that you receive with your collector hood has
a stepped design that will allow it to accept either a 6"
blower hose (C, Figure 20) and a 7" blower hose (B). If you
are installing the 3-bag collection system that uses a 6"
blower hose, no changes to the inlet are necessary. If you
are installing the 3-bag collection system that uses a 7"
blower hose you must use the indicator (D) as a guide and
cut off the stepped end of the collector inlet. If you are
installing a 2-bag collection system, no changes to the inlet
are necessary.
20
2. Open the collector hood.
3. Install the collector inlet (A, Figure 21) from the inside of
the collector hood (B) so that the channel (A, Figure 20)
snaps into the collector hood which will allow the collector
inlet to rotate.
21
Install the Collector Hood Latch
1. Route the 5/16 X 1-1/4" bolt (D, Figure 22) through a 5/16
USS washer (C), the collector hood latch (B), the small
spacer (A), and a second 5/16 USS washer (C).
22
2. Install a fender washer (F) onto the bolt stud (E)
3. Align the slot in the collector hood latch with the bolt stud
(E) on the side of the collector hood and then finish routing
the 5/16 X 1-1/4" bolt through the collector hood and secure
with a 5/16 USS washer (C) and a 5/16 nylock flange nut
(G).
4. Install a second fender washer (F) and the lock nut (H) onto
the bolt stud and tighten it so that two threads show through
the end of the nut.
Install the Grass Collection Bags
1. Install the two rubber caps (A, Figure 23) on the ends of
the bag frame (B).
23
2. Install the bag frame into the collector bag (C). The end with
the two rubber caps is away from the solid back and the
opening in the top of the bag.
3. Slide the collector bag (A, Figure 24) into the frame rail (B).
11
Not for
Reproduction
24
4. Repeat the process for the remaining bags.
Install the Discharge Tube
1. Lower the unit's mower deck to it's lowest cutting position.
2. Install the discharge tube (A, Figure 25) onto the blower (C)
and secure with the removable clamp with knob (B). At least
two bands must cover the outlet of the blower.
25
3. Cut the discharge tube to the proper length so that it will fit
properly between the blower and the collector as shown in
Figure 26. When installed, at least two bands of the
discharge tube must cover the inlet of the collector. From
the blower to the collector the discharge tube must be as
straight as possible to help prevent grass clumping in the
discharge tube.
26
4. Install the discharge tube (A, Figure 27) onto the collector
inlet (B). Secure with the stationary clamp (C).
27
Install the Weights and Weight Mounts
It is important that the weight carrier and the front weights are
installed whenever the collection system is mounted on your
unit.
Install the Weights and Weight Mount (IS3100Z
Models)
1. Measure and mark the front main frame tubes to the
dimensions as referenced in Figure 28 and the chart below.
DimensionZTR Unit's Serial
Number
Reference
5" (12,7 cm)2016270588 & BelowA
4-1/2" (11,4 cm)2016270589 & Above
1-1/4" (3,38 cm)AllB
12 ferrismowers.com | snapperpro.com
Not for
Reproduction
28
2. Using a 3/8" drill bit, drill one (1) hole in each of the main
frame tubes from the outside surface of the tube.
3. Slide the weight mount rack into the main frame tubes and
align with the holes drilled through the frame (see Figure
29). It may require you drive the arms into the frame tubes
using a wooden block and hammer.
29
4. Finish drilling through the opposite wall of the frame tubes
using the weight rack as a guide.
5. Install the 3/8” bolts from the inside of the frame rail and
fasten securely with the nylon lock nuts.
6. Install the two (2) 50 lbs counter weights supplied with the
grass collector on the weight mount rack (see Figure 30).
30
7. Install the weight retainer rod through the weight mount rack
and secure with hairpin clips (see Figure 30).
Install the Weights and Weight Mount (Units w/
3/8" Holes)
1. Install the weight carrier (A, Figure 31) onto the front of the
unit and secure with two (2) 3/8 X 1-1/4" bolts (B), 3/8 flat
washers (C), and 3/8 nylock flange nuts (D).
31
2. Install the counter weights (E) in the weight carrier and
secure with the retaining pin (F) and hair pin clips (G). A
2-bag system gets two (2) 30 lbs weights and a 3-bag
system gets two (2) 50 lbs weights.
Install the Weights and Weight Mount (Units w/
1/2" Holes)
1. Install the weight carrier (A, Figure 32) onto the front of the
unit and secure with two (2) 1/2 X 1-1/4" bolts (B), 3/8 flat
washers (C), and 1/2 nylock flange nuts (D).
13
Not for
Reproduction
32
2. Install the counter weights (E) in the weight carrier and
secure with the retaining pin (F) and hair pin clips (G). A
2-bag system gets two (2) 30 lbs weights and a 3-bag
system gets two (2) 50 lbs weights.
Operation
General Operating Instructions
Before Operation
Clear the lawn of all sticks, stones, wire and other debris which
may be caught or thrown by the mower blades.
Check grass condition. If wet, wait until later in the day. If grass
is wet, the grass catcher is likely to become plugged.
For efficient bagging, air circulation under the mower deck,
through the chute and into the bag is very important.
For this reason, BEFORE YOU BEGIN MOWING you should
make certain the underside of the mower and the underside of
the catcher lid are free from grass and debris.
Make sure that there is a snug fit between mower deck, blower
housing, discharge tube, and grass catcher cover.
Mowing with the Double / Triple Catcher
Always operate with throttle at full speed when mowing.
Grass should be cut often, and not too short. If grass is too long
or lush it may be necessary to keep ground speed to a minimum
or to cut only half the width of the mower to prevent clogging.
If grass is long, operate with mower in high cutting postion for
first pass, cutting again in a lower position on a second pass.
Do not open the cover with mower engaged.
If a large amount of cut grass is spilling out from under deck,
the discharge tube mar be plugged or the bags may be full --
Disengage the blower (blades) and remove the ignition key,
wait for all parts to stop and then empty the catcher or clear the
discharge tube.
WARNING
Disengage the blower (blades) and remove the ignition key,
wait for all parts to stop before disconnection or unlatching
any parts attached to blower or collection system.
To reduce fire hazard, keep the engine, rider and mower free
of grass, leaves and excess grease. Do not stop or park rider
over dry leaves, grass or combustible materials.
CAUTION
Always wear hearing protection when operating.
Note:
Be careful when turning away from objects. The bagger
may collide with objects causing damage.
After Operation
For the blower:
1. The blower housing and discharge tube should be removed
for cleaning.
14 ferrismowers.com | snapperpro.com
Not for
Reproduction
For the collection system:
1. Remove any accumulated debris from the inside of the
collection unit.
2. Remove any debris from the screen on the underside of
the lid, if equipped.
Note:
The lid screen can be partially removed for easier cleaning
and should be cleaned regularly.
3. Inspect the grass bags for wear or damage.
NOTICE
Collector bags are subject to deterioration and wear
during normal use. Inspect the bag periodically for tears, holes,
or weak spots, and replace with a new bag that meets the
manufacturer's durability standards.
4. Make sure that there is a snug fit between mower deck,
blower housing, discharge tube, and grass catcher cover.
Storing the Grass Catcher
Clean the grass catcher thoroughly using a mild detergent (other
products may damage the discharge tube). Remove any debris
from the screen on the underside of the lid. The screen can be
partially removed for easier cleaning.
If paint has been scratched on metal parts, touch up with paint,
or apply a thin film of oil to prevent corrosion.
Store in a dry area. Hang the catcher and catcher bags to dry
thoroughly before storing for a long period of time. Always store
away from moisture.
Mowing Without the Collection System
To remove the blower, see the instructions in
Collector System
Removal
. All of the instruction must be followed in
Collector
System Removal
to remove the collector, blower, collector
hose, and front weights, and the discharge chute properly
installed and adjusted in the down position.
DANGER
Thrown Objects Hazard
• Do not mow without discharge chute or entire grass
catcher in place.
WARNING
Warning - Loss of traction and control hazard:
• Do not operate with only the collection system installed.
• Do not operate with only the front counter balance weights
installed.
• Operate only with both the entire collection system and
front counter balance weights installed and the collection
system closed and latched.
Opening and Closing the Collector Hood
1. To open the hood, unlatch the two bungee straps (A, Figure
33). There is one of each side of the collector hood and lift
the collector hood. The collector hood latch (B) will hold the
hood open.
33
2. To close the hood, lift the hood and pull the collector hood
latch towards the rear of the unit and then lower the collector
hood. Latch the two bungee straps to secure the hood shut.
Troubleshooting
Troubleshooting Charts
Troubleshooting the Collection System
Problem: Excessive vibration.
RemedyCause
Replace the mower deck cutting
blades.
Mower deck cutting blades are bent or
unbalanced.
Tighten the blade mounting bolts to 70
ft. lbs. (94 Nm).
Mower deck cutting blade mounting
bolts are loose.
Tighten the appropriate pulley.
Replace if excessively worn.
Loose blower pulley.
See your dealer.Blower impeller blades are bent or
broke.
Problem: Excessive grass blowout from the mower deck.
RemedyCause
Empty bags.Collection bags are full.
Locate and remove plugged debris.Blower or discharge tube is plugged.
Use a slower ground speed.Ground speed is too fast.
Problem: Blower and discharge tubes are plugging
frequently.
RemedyCause
Empty bags.Collection bags are full.
Use a slower ground speed.Ground speed is too fast.
Cut grass when it is dry.Grass is too wet.
Cut grass at a higher deck height
setting.
Grass is too long.
Replace with a new blower belt.Blower belt is worn, loose, or broken.
15
Not for
Reproduction
Unplugging a Clogged Unit
Conditions such as grass that is too long or too wet or cutting
at too fast of a ground speed could cause the blower and the
discharge tube to become clogged.
If any part of the collection unit becomes clogged while in
operation, follow these procedures to safely remove the clog
from the unit.
WARNING
High speed discharge can cause injury or death. Do NOT run
blower without discharge tube, hood and bags installed and
latched. Before cleaning, discharge tube or blower, disengage
PTO, stop the engine and remove the key.
Never place hands into blower housing to clear jammed objects
or plugged blower. Blower may rotate when object is removed.
If the discharge tube is clogged:
1. Park the machine on a flat, level surface. Disengage the
PTO, engage the parking brake, turn off the ignition and
remove the ignition key.
2. Loosen the lower clamp (with knob) (A, Figure 34) securing
the discharge tube to the blower outlet and remove the
discharge tube from the blower.
34
3. Shake the discharge tube to loosen the clog from the
discharge tube.
4. If the clog will not loosen use a suitable tool, such as a
broom handle, to clean the clog out of the discharge tube.
5. When the obstruction is cleared, re-install the discharge
tube onto the blower outlet and secure in place with the
lower clamp (with knob).
If the blower is clogged:
1. Park the machine on a flat, level surface. Disengage the
PTO, engage the parking brake, turn off the ignition and
remove the ignition key.
2. Loosen the lower clamp (with knob) (A, Figure 34) securing
the discharge tube to the blower outlet and remove the
discharge tube from the blower.
WARNING
Never place hands into blower housing to clear jammed
objects or plugged blower. Blower may rotate when object is
removed.
3. Use a suitable tool, such as a broom handle, to clear the
obstruction from the blower.
4. When the obstruction is cleared, re-install the discharge
tube onto the blower outlet and secure in place with the
lower clamp (with knob).
If the collector inlet is plugged:
1. Park the machine on a flat, level surface. Disengage the
PTO, engage the parking brake, turn off the ignition and
remove the ignition key.
2. Unlock and open the hood of the collector.
3. Use a suitable tool, such as a broom handle, to clear the
obstruction from the collector inlet (A, Figure 35).
35
4. Loosen the lower clamp (with knob) (A, Figure 34) securing
the discharge tube to the blower outlet and remove the
discharge tube from the blower.
5. Shake the discharge tube to loosen the clog from the
discharge tube.
16 ferrismowers.com | snapperpro.com
Not for
Reproduction
6. When the obstruction is cleared, re-install the discharge
tube onto the blower outlet and secure in place with the
lower clamp (with knob).
7. Lower the hood and lock into place.
Collector System Removal
See the blower's operator's manual included with the blower
mount for instructions on removing the blower from the mower
deck. Whenever the collector is removed from the unit the
blower, and the blower mount must also be removed.
1. Loosen the lower clamp with knob (A, Figure 36) securing
the discharge tube to the blower outlet and remove the
discharge tube from the blower.
36
2. Empty the grass collection bags and reinstall in the collector
bag frame.
3. Remove the hitch pins (A, Figure 37) securing the collector
mount posts to the collector mount plate.
37
4. Lift the collector unit up and off the mount plate.
5. Remove the hairpin clips from the weight retainer rod and
remove the front weights from the weight mount rack (See
Figure 38)
38
17
Not for
Reproduction
Notes
Not for
Reproduction
Notes
Not for
Reproduction
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Simplicity 5600784 User manual
- Category
- Air blowers/dryers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ferris 5100075 User manual
-
Simplicity 1695285 User manual
-
-
-
-
-
-
-
-
Ferris FAST-Vac User manual
Other documents
-
Ferris Automobile Accessories 5600056 User manual
-
Snapper Z Series User manual
-
Toro Rear Discharge Mower Shield Kit, ProLine 118 User manual
-
Wright Manufacturing 98320009 User manual
-
-
-
-
-
-
