Infinite Peripherals Infinea X DF User manual

Infinea X DF

USER MANUAL

For iPhone® 7 / 8 / SE / HID™

Inﬁnea X DF User Manual

Table of Contents

Legal Notice 3

Compatible Devices 3

Trademarks 3

Box Contents 3

Getting Started 4

Accessories 4

Technical Speciﬁcations 5

Electrical 5

Mechanical 5

Environment 5

About Your Inﬁnea X DF 6

Programmable Options 8

Developing Applications Using the SDK 8

Getting Started 9

Install Battery 9

Assemble Inﬁnea X DF 9

Charge Inﬁnea X DF 10

Battery Status Indicator 10

Charge Battery 10

Charge Using Electrical Outlet 11

Battery Disposal 11

Sync With iTunes 11

Turn on the Inﬁnea X DF 12

Scan barcodes 12

Enable RFID/HID 12

Reset Inﬁnea X DF 12

Troubleshooting 13

Cleaning Guidelines 14

Cleaning Precautions 14

Warranty 15

Disclaimer 15

Product Returns and Servicing 15

Symbols 16

Federal Communications Commission 16

Contacts

Mobility Sales/ Technical Support Center

Inﬁnite Peripherals, Inc.

17681 Mitchell N

Irvine, CA 92614-1605

Toll-Free 866.278.7860

Ofce 949.222.0300

Website https://ipcmobile.com

Headquarters/ Main Warehouse

Inﬁnite Peripherals, Inc.

2312 Touhy Avenue

Elk Grove Village, IL 60007-5329

Toll-Free 800.278.7860

Ofce 847.818.1260

Fax 847.818.1287

Inﬁnea X DF User Manual

Compatible Devices

Legal Notice

“Made for iPhone” means that an electronic accessory has been

designed to connect speciﬁcally to the iOS device and has been certiﬁed

by the developer to meet Apple performance standards. Apple is not

responsible for the operation of this device or its compliance with safety

and regulatory standards. Please note that the use of this accessory

with a HID or iOS device may affect wireless performance.

Made for these mobile devices:

iPhone® 7 / 8 / SE

Trademarks

Inﬁnite Peripherals, Mobilize Your Enterprise, Linea Pro, Inﬁnea, Inﬁnea

Tab and Inﬁnea Omni are trademarks of Inﬁnite Peripherals, Inc. All

other trademarks are the property of their respective owners.

Box Contents

• Before using your Innea X DF, remove the unit and any included

accessories from the shipping cartoon and verify the contents

against the packing list.

• Retain all packing materials, invoice, and bill of lading. These may

be required to return the device for servicing later, or to process

a claim with the shipping carrier.

• Carefully inspect the contents inside of the packaging for any

signs of damage. If there are signs of damage, do not attempt to

use the unit. Notify your account executive or contact technical

support at https://ipcmobile.com/devices.

• Ensure the battery is fully charged prior to initial use.

Torx T6 screws (6)

Inﬁnea X DF (1) Standard battery (1)

Charging cup (1)

Note

Box contents and part numbers vary based on your order

conﬁguration.

The following items are included in the box.

Inﬁnea X DF User Manual

Inﬁnea X DF Features

Inﬁnea X DF allows you to scan barcodes into an iOS device. Before

using the Inﬁnea X DF, charge the battery fully.

These are the key features of the Inﬁnea X DF.

Feature Description

Barcode

scanner

Supports one-dimensional (1D) and two

dimensional (2D) barcode symbols, which can

be read in any direction (omni-directional). The

effective reading distance of the barcode reader

varies depending on the barcode size. The

barcode scanner is capable of reading barcodes

on a LCD screen.

RFID/HID RFID tag/card reader reads/writes at 13.56MHz.

Battery User replaceable Li-ion battery.

Indicators Three programmable indication features:

Audible — internal electro-magnetic buzzer

Visual — four multi-color SDK LEDs (blue, green, red, and

orange).

Haptic — programmable vibration motor.

Power

monitoring

On-board fuel gauge, which facilitates accurate

monitoring of signiﬁcant battery attributes using

the SDK.

Bluetooth Available Bluetooth 2.0 SPP compatibility, which

allows connection to a Bluetooth peripheral, such

as a printer.

Case Case for the unit is rated IP54 for protection

against dust and ﬂuid access.

Getting Started

To get you up and running with your new unit, review these sections.

Observe any notes, cautions, or warnings throughout this guide for

additional information, special care required, or important points to

prevent injury or adverse affects.

What to do Section Why is this important?

Install battery Install Inﬁnea X

DF battery pack

Your unit is shipped with

approximately 30% of the full

charge capacity.

Before initial use charge the

battery completely.

Charge Inﬁnea

X DF

Charge the

Inﬁnea X DF

Install

software

Develop

applications

Before using the barcode

scanner, RFID/HID reader, and

LED indicator features you must

install software onto your iOS

device.

Power on the

Inﬁnea X DF

Turn on the

Inﬁnea X DF

Initializes the barcode scanner

and/or RFID/HID functionality.

Accessories

Visit our website at https://ipcmobile.com or contact your Inﬁnite

Peripherals account representative for additional information about our

current and future product accessories.

Inﬁnea X DF User Manual

Barcode Scanner

• 2D high-speed imager

• Supports all major 1D and 2 D barcodes

Battery Capacity

• User-rechargeable lithium-Polymer battery

• 3.7V /1900 mAh

Connectivity

• Apple Lightning™ connector

• Pass-through sync via iOS

Contactless Card Reader (RFID)

• SO/IEC 14443 Type A/MIFARE

* MIFARE MINI

* MIFARE CLASSIC-1K, MIFARE CLASSIC-4K

* MIFARE ULTRALIGHT, ULTRALIGHT-C

* MIFARE PLUS 2K/4K

* DESFire card

* FeliCa

• ISO/IEC 14443 Type B supports most cards

• ISO/IEC 15693

HID

MIFARE® Classic 1K / 4K, Ultra Light, Ultra Light C,

Plus, MIFARE DESFire 0.6, MIFARE DESFire EV1,

iCLASS, iCLASS SE, T=CL, ISO 14443 A with up to 848

kbps transmission rate (depending on card), ISO 15693

with up to 26 kbps transmission rate (depending on

card), iCLASS Seos

Bluetooth

• Bluetooth 2.0 class

• Distance up to 10m

• Serial port prole (SPP)

Power supply

• DC 5V

• 1 A through micro USB connector

Power consumption

• Deep sleep -20uA

Indicators

• Audio — electromagnetic buzzer

• Visual — Four programmable colorful LEDs

* Green

* Blue

* Red

* Orange

Technical Speciﬁcations

Mechanical

Buttons

• iOS On/Off

• Scan

• Battery status

• Programmable

• Volume

Port

USB Type-C for device charge and sync

Processor

32-bit ARM Cortex - M3 MCU

Environment

Operating Temperature

+10° to +40°C / 50°F to +104°F

Storage Temperature

-20° to +50°C / -4°F to +122°F

Relative humidity for operating and storage

5% to 90%

Certifications

• CE, FCC, Apple MFI

• Drop rating 1.22m (4 ft)

• IP54 rated

Note

Speciﬁcations may change without notice.

SKUs: IX-Z2DBTR-PH7-LG; IX-Z2DBTR-PH7-MG; IX-Z2DBTR-PH8-LG;

IX-Z2DBTR-PH8-MG; IX-Z2D-PH7-HID-LG; IX-Z2D-PH7-HID-MG

Electrical

Compatibility

• iOS device 7 / 8 / SE

• HID

Dimensions

164mm (L) x 83mm (W) x 27.7mm (H) (6.5in. (H) x 3.3in (W) x 1.1in (H)

Weight

213 g with battery (7.52 oz.) without iOS device

Inﬁnea X DF User Manual

About Your Infinea X DF

















1. iOS device receiver port

2. Flat-head T6 screws

3. iOS device On/Off button

4. Scan button

5. Status LEDs

6. Programmable button

7. Home button

8. Battery status button

9. Volume buttons

10. iOS device camera opening

11. Barcode scanner

12. RFID/HID antenna

13. Battery pack

14. Battery latch

Inﬁnea X DF User Manual

Programmable

Button

Scan Button

iOS On/Off

Button

Volume Buttons

Battery Status

Button

Inﬁnea X DF User Manual

Programmable Options

These optional settings are conﬁgured in the SDK.

Programmable

options

Description

Set Charging Enables or disables battery backup sharing

capability to charge the iOS device from the IX

removable battery.

Scan Mode

• Single Scan

Scanning a single barcode by pressing the

Scan button.

• Multi Scan

Scanning multiple barcodes by pressing

and holding the Scan button.

• Motion-Detect

Scanner is activated automatically when

barcode is placed near the barcode

engine.

• Multi-Scan without Duplicates

Scanning multiple barcodes without

duplicates.

Pass Through

Sync

When the pass through sync setting is enabled

and the charging cup is plugged into the wall

outlet, the iOS device may be synced with a PC

or MAC. Default setting is off.

Note: If Pass Through Sync is enabled, the iOS

device does not charge when plugged into an

external charger.

Time Out Set timeout for a minimum of 60 seconds or up

to 64,800 seconds (18 hours).

Developing Applications Using

the SDK

Software is not automatically provided with your unit.

Integrating the device into your application requires the use of

the Inﬁnite Peripherals Universal SDK. The SDK incorporates an

API speciﬁcally for developing applications to use with your unit’s

functionality.

For additional details on using the Inﬁnite Peripheral Universal SDK,

please refer to the appropriate SDK documentation. You can contact

your Inﬁnite Peripherals account representative for third-party software

solutions.

For the latest Inﬁnite Peripheral Universal SDK please visit our

developer portal:

https://developer.ipcmobile.com

Inﬁnea X DF User Manual

Assemble Inﬁnea X DF

1. Verify the battery latch is fully open.

Note

Be careful to not force the battery into place, if the latch is closed and

locked.

2. Lower the battery pack into place so it seats at when installed.

3. With slight pressure on the back of the battery, use your ngers

to rotate the latch counter-clockwise 90 degrees, or until it is

securely locked into place.

Getting Started

Install Battery

1. Open the unit by loosening the six socket head hex screws, and

then gently ip open the top cover.

2. On your iOS device, set the ring silent switch to Ring mode.

3. Slide the iOS device onto the Lightning™ connector until it clicks

into place.

The Inﬁnea X DF is molded speciﬁcally to the compatible iOS device. iOS

devices are not interchangeable

4. Close the top cover while maintaining the position of the

protective rubber bumper.

Before closing the top cover, wipe the interior glass with a clean, lint-

free cloth to ensure the screen is clean and free from moisture.

5. Tighten the six screws in the upper enclosure to secure it in this

order:

* Top left

* Bottom right

* Top right

* Bottom left

* Center left

* Center right

Between the top and bottom covers ensure the rubber bumper is

properly aligned. Failure to do so compromises the liquid protection

functionality of the unit.

Inﬁnea X DF User Manual

Charge Infinea X DF

You can charge the Inﬁnea X DF by either an AC wall outlet or by

replacing the battery. Pass-through charging to your iOS device is

supported.

Based on charging requirements, the Inﬁnea X DF and iOS device

cannot be charged together using a USB cable to a PC connection.

Battery Status Indicator

To check the battery life of the unit, press the battery status button on

the bottom left or right-hand side, and then observe the color of the LED.

Note: if the green LED is not illuminated on the unit while charging,

verify the connector is properly attached and the unit is seated

securely in the charging cup accessory. If a problem persists, contact

https://ipcmobile.com/support.

Charge Battery

You can charge up to ten batteries at once using the multi-bay charger.

Each battery slot in a single LED charge.

Note

Standard batteries take approximately 2.5 hours to fully charge. The

extended battery requires about 5 hours to charge. When the LED

is green, the battery is fully charged; red indicates charging is in

progress.

Charging times for the Inﬁnea X DF is three hours with or without the

standard battery inserted. If back-up charging is enabled and both iOS

device and Inﬁnea X DF are fully discharged, insert a new, completely

charged standard battery into the unit and charge for about 10-15

minutes using the charging cup. After 15 minutes, remove the charging

cup so the Inﬁnea X DF provides back-up charging to the iOS device, as

needed.

Note

When not in use, remove the battery and turn off the iOS device.

Status Description

100-75% Solid green

74%-50% Blinking green

49%-25% Blinking orange

24%-10% Blinking red

9%-1% One LED blinking red indicating emergency low

battery status

When the remaining battery capacity is below 15%, the automatic charge on the

iOS device stops.

• Standard battery capacity is 1900mAH.

• Extended battery sold separately is 3800mAH.

Inﬁnea X DF User Manual

1. Insert the standard battery into the Innea X DF, and then

attach the charging cup to the bottom of the unit. When you

hear a click the device is fully seated in the cup.

2. Plug the USB connector end of the charging cup into an AC

wall adapter, and then conrm the LED indicator turns green

indicating charging is active.

Note

To prevent electrical damage to the unit or iOS device, only use the

approved charging cup shipped with the Inﬁnea X DF.

Battery Disposal

Dispose of used batteries in accordance with current law, which may

include disposing them at a battery-recycling center or hazardous-

waste collection site.

Charge Using Electrical Outlet

Sync With iTunes

You can sync your iOS device with iTunes using the Inﬁnea X DF.

1. Connect the Innea X DF to a computer using the charging cup.

2. If the unit is not in sync, refer to the iTunes documentation for

instructions.

3. To disable sync mode, exit iTunes.

4. Unplug the unit from the charging cup.

Note

If sync does not work, contact https://developer.ipcmobile.com.

Inﬁnea X DF User Manual

Reset Infinea X DF

You can do a soft-reset without removing your iOS device to cycle

through the power allowing the Inﬁnea X DF to restart.

1. Press the Scan button and Battery Status buttons

simultaneously for approximately three seconds.

2. When you hear an audible beep, the main-board is reset.

3. Release all buttons and the unit restarts.

Turn on the Infinea X DF

When the Inﬁnea X DF is turned off or in sleep mode, press the scan/

power button to turn it on. A single beep is heard indicating it’s ready

for use.

• Press the scan button again to activate the scanner for barcode

scanning.

Note

Customized software must be used for the Inﬁnea X DF to

communicate with your iOS device. Refer to https://developer.

ipcmobile.com or contact your Inﬁnite Peripherals representative.

Scan barcodes

1. To scan a barcode, press the Scan button on the top of the

Innea X DF.

2. Aim the red target at the barcode between the barcode and the

scanner and the barcode is with the width of the red illumination

cross hairs.

3. Slowly pull backwards to increase the distance between the

barcode and the scan engine until the barcode is read.

Enable RFID/HID

• To use the RFID or HID functionality, press the Scan button.

• For RFID, place the card/tag face down and as close as possible

to the receiver/transmitter.

Note

Depending on the type of tag/card, you may need to place it directly on

the surface of the RFID receiver/transmitter properly read or write the

data.

Inﬁnea X DF User Manual

Troubleshooting

If you encounter issues in general, with scanning barcodes, or using the

RFID/HID functionality, refer to these possible causes and resolutions.

If problems persist and not resolved by the resolutions indicated,

contact technical support at https://ipcmobile.com/devices

Issue Reason

RFID/HID

RFID or HID

does not turn

on.

Battery is too low.

Unit is not powered by software.

Reader if faulty.

Charging cup is connect to unit.

Partial or no

data is returned

during scan.

Unreadable tag or card.

Battery is low.

Faulty reader.

Software decoding incorrectly.

Speciﬁc tag/

cards not read.

Tag or card type not conﬁgured.

Issue Reason

General issues

iOS device does

not sync with

iTunes.

Inﬁnea X DF is not conﬁgured to sync.

iOS device touch

screen not

responding to

swipe or tap.

Top cover is not properly installed.

iOS device requires restarting.

iOS device does

not charge.

AC adapter (not included) may not meeting

charging requirements.

Pass-through sync is enabled.

Barcode scanner

Scanner does not

turn on.

Batter is too low.

Unit not powered on by software.

Scan engine is faulty.

Charging cup is connected Inﬁnea X DF.

Barcode data not

returned during

scanning.

Barcode is unreadable.

Battery is too low.

Scan engine is faulty.

Software decoding incorrectly.

Multi-scanning

not working.

Multi-scan mode not enabled.

Software does not support multi-scan.

Scanner beep not

heard.

Sound mode not enabled.

Battery is too low.

Speciﬁc barcodes

do not scan.

Barcode type is not conﬁgured.

Inﬁnea X DF User Manual

Cleaning Guidelines

• Do NOT autoclave, machine wash, pressure-sterilize or gas-

sterilize the Innea X DF.

• Do NOT soak or immerse in any liquid.

• Clean the Innea X DF only when the battery module is properly

installed and locked into the Innea X DF. This will ensure proper

sealing of the Innea X DF prior to introducing any solutions

and/or wipes used during the cleaning process.

• Apply cleaning solutions with a soft lint-free cloth. If the solution

comes in the form of a wipe, ensure the wipe is lint-free and will

not scratch the plastic surfaces (especially the scan window).

Excessive solution that resides in any of the waterproof

membrane or gasket areas can seep into the devices and cause

damage to the internal components.

• Do not touch, press or rub the display and/or covers with

abrasive cleaning compounds, instruments, brushes, rough

surface material or bring the display and/or covers into contact

with products that could potentially scratch the display or

covers.

• To clean the Innea X DF screw areas, use a soft-bristled brush

with approved cleaning solutions. Focus cleaning in the screw

areas, ensuring that the brush is not used in areas that contain

seals or gaskets.

• Do not use ammonia based, petroleum-based or acetone

cleaning solutions to clean the Innea X DF. Also avoid harsh

solvents.

• Use the following cleaning solutions only to clean the Innea X

DF exterior surfaces:

* Clorox®Bleach (10%)

* Isopropyl Alcohol Wipes (70%)

Cleaning Precautions

The Inﬁnea X DF is certiﬁed to meet IP54 Ingress Protection Marking

per IEC 60529. Per the IP54 rating, the Inﬁnea X DF is protected against

interference with normal operation of the Inﬁnea X DF sled caused by

dust and splashing liquids. At no time should the Inﬁnea X DF sled be

completely immersed in liquid. Total submersion of the device may allow

liquid to enter the unit and impair its normal function. Immersion will

also void the Inﬁnea X DF warranty.

The end user should determine an appropriate cleaning procedure

that complies with any facility and/or industry-speciﬁc cleaning

requirements. The following information is a general cleaning guideline

that should be followed to ensure the Inﬁnea X DF maintains its normal

operation.

Inﬁnea X DF User Manual

Warranty

Inﬁnite Peripherals does not warrant, and is not responsible for, any

damage to the Inﬁnea X DF (“Product”) or the assembled iOS device as

a result of liquid or solid particle intrusion into the Product, or damaged

caused by dropping the Product with the assembled iOS device. If

a material or workmanship defect arises with regard to any Inﬁnite

Peripherals product, and a valid claim is received within the Warranty

Period, Inﬁnite Peripherals (at our sole discretion) will repair the

Product using new or refurbished parts, or replace the Product with a

new or refurbished Product.

For purposes of this limited warranty, “refurbished” means a product or

part that has been substantially returned to its original speciﬁcations. In

the event of a defect, these are your exclusive remedies.

Disclaimer

NO WARRANTY. This technical documentation is provided AS-IS. Further,

the documentation does not represent a commitment on the part of.

Inﬁnite Peripherals, Inc does not warrant that it is accurate, complete

or error free. Any use of the technical documentation is at the risk of

the user. Inﬁnite Peripherals, Inc reserves the right to make changes

in speciﬁcations and other information contained in this document

without prior notice, and the reader should in all cases consult Inﬁnite

Peripherals, Inc to determine whether any such changes have been

made. Inﬁnite Peripherals, Inc shall not be liable for technical or

editorial errors or omissions contained herein; nor for incidental or

consequential damages resulting from the furnishing, performance,

or use of this material. Inﬁnite Peripherals, Inc does not assume any

product liability arising out of or in connection with the application or

use of any product or application described herein.

Product Returns and

Servicing

Use the link in step 1 to create an account and gain access to our

Knowledge Base and online support services. Through our online

support center, you’ll be able to download ﬁles, open a Support Ticket,

manage your RMAs, view your account Proﬁle and subscribe to Alerts.

To request a RMA

1. Create a user account in the RMA Support Portal at http://

ipcmobile.com/support/rma/

2. Login to your user account, and then click Create RMA Request.

3. Read the instructions provided and complete the online request

form.

4. Note the assigned RMA number and write it clearly on your

shipping carton.

5. Ship your equipment back to us using the address provided.

Inﬁnea X DF User Manual

Symbols

Symbol Description

Refer to the instructions before using.

Manufacturer

Manufacture Date

Caution

Serial Number

P/N

Part Number

Waste Electrical and Electric Equipment

Complies with part 15 of the FCC rules

Near-ﬁeld communication (NFC)

Federal Communications

Commission

Federal Communications Commission (FCC)

Statement

15.21

You are cautioned that changes or modiﬁcations not expressly

approved by the part responsible for compliance could void the

user’s authority to operate the equipment.

15.105(b)

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and

receiver.

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician

for help.

Operation is subject to the following two conditions:

•

This device may not cause interference and

•

This device must accept any interference, including

interference that may cause undesired operation of the

device.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. End users must follow

the speciﬁc operating instructions for satisfying RF exposure

compliance. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

Infinite Peripherals Infinea X DF User manual

Related papers

Other documents