OPERATOR’S
MANUAL
84100X
RELEASED: 10-4-99
REVISED: 1-22-14
(REV.
F)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
MATERIAL FILTER
MAXIMUM
INLET PRESSURE 6,000 P
.S.I. (414 BAR)
READ THIS MANUAL CAREFULL
Y BEFORE INST
ALLING,
OPERA
TING OR SER
VICING THIS EQUIPMENT
.
It
is the responsibility of the employer to place this information in the hands of the operator
. Keep for future reference.
SERVICE KITS
Use only genuine Binks replacement parts to assure compatible presĆ
sure rating and longest service life,
MATERIAL FIL
TER DA
TA
MODELS 84100X......................
MATERIAL (models 841001 and 841002) Carbon steel
(models 841005 and 841006) Stainless Steel
MAXIMUM FLUID PRESSURE 6,000 p.s.i.g. (414 bar)......
OPERATING
& SAFETY PRECAUTIONS
Z Read and heed all Warnings, Cautions and Safety Precautions
before operating this pump.
Z Use only genuine Binks replacement parts to assure compatĆ
ible pressure rating and longest service life.
WARNING
HAZARDOUS PRESSURE. Can result in serious
injury or property damage. Do not service or clean pump,
hoses or dispensing valve while the system is pressurized.
CAUTION Be certain all operators of this equipment have
been trained for safe working practices, understand it's limitaĆ
tions, and wear safety goggles / equipment when required.
WARNING DO NOT EXCEED MAXIMUM INLET AIR PRESĆ
SURE AS STATED ON AIR MOTOR MODEL PLATE. OPERATĆ
ING PUMP AT HIGHER PRESSURE MAY CAUSE PUMP
DAMAGE.
WARNING HAZARDOUS MATERIALS. Can cause serious
injury or property damage. Do not attempt to return a pump to
the factory or service center that contains hazardous material.
Safe handling practices must comply with local and national
laws and safety code requirements. Obtain Material Safety
Data Sheets on all materials from the supplier for proper hanĆ
dling instructions.
FIGURE 1
MODEL
DESCRIPTION CHART
84100 X
BODY MATERIAL / SCREEN MESH SIZE
1 - Carbon Steel / 70 Mesh
2 - Carbon Steel / 100 Mesh
5 - Stainless Steel / 70 Mesh
6 - Stainless Steel / 100 Mesh
GENERAL
DESCRIPTION
The Binks Material Filter is used to separate foreign materials like dirt,
stones and sweeping compound, from the material handling section.
Material filters and strainers can be installed in a system to combat this
problem, thereby achieving longer service life. At this point, where the
fluid enters the material handing section, the strainer prevents foreign
material from entering the system.
U.S.A. / Canada Customer Service
195 Internationale Blvd
Glendale Heights, IL 60139
Tel. 630-237-5000
Fax. 630-237-5011
Toll Free Customer Service
and Technical Support
800-992-4657
Toll Free Fax
888-246-5732
CCN 99866717
84100XPAGE 2 OF 4
TYPICAL
SYSTEM VIEW
1. Install material filter either at the inlet of material handling section or
upstream from the other accessories (control handle, etc.).
2. Refer to typical installation (see figure 2).
3. The filter unit was tested at the factory with a maximum working
pressure of 6,000 p.s.i. (414 bar).
4. Two 1/2 Ć 14 N.P.T. pipe plugs (item 8) are included with this unit to
plug an inlet and an outlet port not being used.
DISASSEMBLY
WARNING
HAZARDOUS PRESSURE. Can result in serious
injury or property damage. Do not service or clean pump,
hoses or dispensing valve while the system is pressurized.
S Disconnect air supply line and relieve pressure from the
system by opening dispensing valve or device and / or
carefully and slowly loosening and removing outlet hose
or piping from pump.
1. Unscrew and remove (1) cap from the (7) body.
2. Remove (2) gasket from (1) cap.
3. Remove (3) spring and (4) guide button from the (7) body.
4. Pull the (6) screen assembly from the (7) body.
Replace worn seals and parts with new parts. Reverse disassembly
instructions for reassembly.
PARTS LIST
ITEM DESCRIPTION (Size in Inches)
QTY
PART NO. [MTL] ITEM DESCRIPTION (Size In Inches)
QTY
PART NO. [MTL]
1 Cap (models 841001 and 841002) (1) [C]
(models 841005 and 841006) (1) [SS]
2 Gasket (1) 873145 [D]
3 Spring (1) 873314 [SS]
4 Guide Button (1) [SS]
6 Screen Assembly
(models 841001 and 841005)(70 mesh) (1) 873146 [SS]
(models 841002 and 841006)(100 mesh) (1) 873147 [SS]
(200 mesh) (1) 873424 [SS]
7 Body (models 841001 and 841002) (1) [C]
(models 841005 and 841006) (1) [SS]
8 Pipe Plug (1/2 Ć 14 N.P.T.)
(models 841001 and 841002) (2) [C]
(models 841005 and 841006) (2) [SS]
84100X PAGE 3 OF 4
PARTS LIST
FIGURE 3
1 =
1/2 Ć 14 N.P.T.F. Ć 1 (INLET)
2
3
4
6
8
7
1/2 Ć 14 P.T.F. SAE SPEC
SHORT (2 OUTLETS)
1/2 Ć 14 N.P.T.F. Ć 1 (INLET)
=
l Lubricate threads with WetĆSol Plus at assembly.
= Torque to 30 Ć 40 ft lbs (40.7 Ć 54.2 Nm).
l
l
2Ć1/4"
(57.2 mm)
1Ć1/16"
(27.0 mm)
8Ć5/16"
(210.7 mm)
2.877"
(73.1 mm)
2Ć1/4"
(57.2 mm)
MATERIAL CODE
[C] = Carbon Steel
[D] = Acetal
[SS] = Stainless Steel
84100XPAGE 4 OF 4
PN 876010
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Ingersoll-Rand SHOCK BLOCKER User manual
-
ARO PD30*-*-B series User manual
-
ARO PD02P Series User manual
-
ARO 66605J Series User manual
-
-
ARO 66605 series User manual
-
-
-
-
