Leviton AWSMT-EBW Operating instructions

Leviton
Brand
Leviton
Model
AWSMT-EBW
Category
Motorcycle Accessories
Type
Operating instructions

This manual is also suitable for

RENOIR II
2 WIRE FLUORESCENT DIMMING CONTROL
Cat. Nos. AWRMG-XXX, AWSMG-XXX & AWSMT-XXX
INSTALLATION
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH ELECTRICAL CODES AND REGULATIONS.
• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.
• DO NOT GANG VERTICALLY.
• ONLY INSTALL FOR THE ALLOWED LOAD TYPES. INSTALLATION FOR ANY OTHER LOAD TYPE WILL VOID WARRANTY AND POSSIBLY CAUSE DAMAGE TO
THIS DEVICE AND/OR CONNECTED EQUIPMENT.
• USE THIS DEVICE WITH COPPER OR COPPER CLAD WIRE ONLY.
Installation Requirements:
• Thesedevicesaredesignedforinstallationintoametal2"x3"(5.08cmx7.62
cm)singlegangormulti-gangdevicebackbox.2-1/2"(6.35cm)ordeeper
backboxesarerequired.Thesedevicesarenotdesignedforamulti-gangeld
conguredbox.Insomeinstallationswhereconduitentryisfromtheside,or,in
multi-ganginstallationswherenipplesbetweentwoadjacentboxesareused,
deeperbackboxesmaybenecessary.Testtinstallationpriortorough-in.
• Installationofmultipledevicesintoasingleboxmayrequirede-ratingandother
specicinstallationprovisions.ReferenceMulti-Gang Installationsformore
details.
•
Asdevicesventtop/bottom,devicesshouldnotbeinstalledvertically
(oneovertheother).
• Toavoidickering,ashing,orlightsononedeviceadjustingwhenanother
device’slevelischanged,donotshareneutrals.Runseparateneutralsforeach
loadcircuitbacktothedevice.(See Figure 1).
Installation Instructions:
1. WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT
CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE
WIRING!
2.Removeexistingwallplateandswitch,ifapplicable.
3.Remove5/8"(1.6cm)ofinsulationfromeachcircuitconductor.Makesurethe
endsofwiresarestraight.
4.ConnectwiresperWIRINGDIAGRAMondeviceasfollows:Twiststrandsofeach
leadtightlytogetherand,withcircuitconductors,pushrmlyintoappropriatewire
connector.Screwconnectorsonclockwisemakingsurenobareconductorsshow
belowthewireconnectors.Secureeachconnectorwithelectricaltape.
5.Installationmaynowbecompletedbycarefullypositioningallwirestoprovide
roominoutletboxfordevice.Mountdeviceintoboxwithmountingscrews
supplied.Snapfaceplateintoplace.
6.Installdevicecontrolpushbuttonandcontrolassembly(see Figure 2).
7.Restorepoweratcircuitbreakerorfuse.Installation is complete.
8.TestDeviceoperation.
INPUT - 120 - 277 VAC 60 HZ
OUTPUT-XA5A
OUTPUT-XB8.3A
OUTPUT-XC12.5A
OUTPUT-XD16A
Features and Operation:
• TurnDeviceONorOFF–PressingtheswitchwillturnthedeviceONifthe
deviceisOFF.IfthedeviceisON,pressingtheswitchwillturnthedeviceOFF.
• SetDeviceLevel–Adjusttheknoborslidertosetthedesiredoutputlevel.When
thedeviceturnsON,thedevicealwaysturnsONtothelevelsetbytheslideror
knob.
• SetCutoffLevel–Thecutofflevelisthelowestvoltagethedimmerwilloutput
beforeshuttingOFF.Tosetthecutofflevel,adjusttheknoborslidertothe
maximumoutput.Slowlylowertheoutputtothedesiredcutofflevel,thenpush
andholdthepowerbuttonfor5seconds.Thedimmerwilladjusttothenewlevel.
Toresetthecutofflevelto0,adjusttheknoborslidertotheminimumoutput,then
pushandholdthepowerbuttonfor5seconds.Ifyourloadisickering,notturning
ON,orsufferingfromanyothererraticbehaviorattheminimumsetting,raising
thecutofflevelmayeliminatetheproblem.
• PresetOperation–Whiledeviceisoff,setlevelofdevice.Thenpressbutton.The
devicewillturnonatthesetlevel.
• PowerRestore–Uponrestorationofpower,thedeviceturnsONtothestateit
wasinatthetimeofpowerloss.
• 5-WayOperation–Linktogether2,3,4,or5devicesformulti-waydimming.
• LEDLocator–AtthebottomoftheswitchisanLEDlocator.Thislocator
illuminateswhenthedeviceisOFFsoyoucanndthedeviceinthedark.
• RemoteControl–Ifyouareusingaremote,theoperationattheremoteis
identicaltotheoperationatthemaster.Aslightreactiondelaymaybenoticedif
operatinglevelchangesveryquickly.
ForTechnicalAssistanceCall:1-800-824-3005(U.S.A.Only)www.leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligation
istocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLevitonManufacturingCo.,Inc.,Att:QualityAssuranceDepartment,201North
ServiceRoad,Melville,NewYork11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,
abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.Therearenootherorimpliedwarrantiesofanykind,includingmerchantabilityandtnessforaparticularpurpose,butifanyimplied
warrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtnessforaparticularpurpose,islimitedtoveyears.Levitonisnotliableforincidental,indirect,special,orconsequentialdamages,including
withoutlimitation,damageto,orlossofuseof,anyequipment,lostsalesorprotsordelayorfailuretoperformthiswarrantyobligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.
PK-93975-10-00-2A
Align flats when
installing knob
Center tab in opening
Figure2-RemoteDimmerAssembly
RotaryDevice SlideDevice
Wiring Diagram
Figure1-DONOTshareneutralwires
Blue
Hot (Black)
Neutral (White)
White
White
Load
Blue
Black
Black
White
Yellow
Yellow
Green
Ground
White
Hot (Black)
Neutral (White)
–
Load
X
–
Run a separate neutral wire
for each control circuit
–
Run a separate neutral wire
for each control circuit
DO NOT
share
neutral
wires
Green
Ground
Dimming Control
LOAD
Black
Blue
Neutral (White)
Hot (Black)
White
White Yellow
For use in multi-way
control (remote)
applications.
Cap wire if not used.
Ground (Green)
Line
120-277VAC
60 Hz
1.Findthecellsthatcorrespondtoyourapplicationbyidentifyingtherowwiththe
numberofwideheatsinkdevicesyouhave,andthecolumnsthatcorrespondtothe
numberofnarrowheatsinkdevicesyouhave.Inthecellyou’llndthefollowing:
2.Thenumberindicatesthenumberof“Gangs”required.
3.Thelettersunderthenumberindicatetheorderdevicesshouldbeinstalled,N=narrow,
W=wide.
4.-W*=rightnbreak-offonwidedevice,N*=rightnbreak-offonnarrowdevice.
-*W=leftnbreak-offonwidedevice,*N=leftnbreak-offonnarrowdevice.
-*W*=nbreak-offonbothsidesofwidedevice,*N*=nbreak-offonbothsidesof
narrowdevice.
5.**indicatesthatuseofjumperbarsisrequired.Jumperbarscanbefoundinthekit
withthefaceplate.
6. Replace'x'inthefaceplatepartnumberwiththedesiredcolor:W=White,I=Ivory,
A=Almond,T=LightAlmond,E=Black,G=Gray,K=24KGold,L=SatinStainless,
R=AntiqueBronze,B=BrushedBrass.
NOTE:Metalnishesarenotavailableoncustomfaceplates.
BasicWIDE/NARROWcongurations,foradditionalcongurationssee:
www.leviton.com/RENOIRII
PK-93975-10-00-2A
©2012LevitonMfg.Co.,Inc.
Multi-WayControl:
TheRenoirIIproductlinesupportsupto5-waycontrol.Anycombinationof
Dimmers,
FanControls,Switches,orRemotesaresupportedwithaMAXIMUM OF
5 DEVICES.TotalrunlengthfromendtoendisMAXIMUM 250 FEET.Remotes
requireUncontrolledHot,Neutral,&Groundforproperoperation.Onetravelerwireis
toruninbetweenallmastersandremotes.Remotesdraw15mApower(ea)fromthe
Controltowhichtheyareconnected.
NOTE:RemoteHot/NeutralshouldideallybefedfromthesamecircuitastheMaster.If
thisisnotpossible,ensurethatthemasterandremotearebothfedfromthesamephase.
MULTI-GANGINSTALLATIONREQUIREMENTS
Additional - Single Gang Box
Multi-WayControlWiringDiagram
Maximum 5 Devices, Dimmers, Remotes or Fan Controls
Maximum 250 feet
Device/Switch
Maximum 5 Devices, Dimmers, Remotes or Fan Controls
Maximum 250 feet
Remote
Device/Switch
Remote
Device/Switch
Remote
Device/Switch
Multiple Device/Switches and Remote Device/Switches
Master
Device/Switch
Remote
Device/Switch
Remote
Device/Switch
Remote
Device/Switch
Remote
Device/Switch
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Traveler
Dimmed Hot
Neutral
Ground
LOAD
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
Traveler
Dimmed Hot
Neutral
Ground
LOAD
Dimmed Hot
Neutral
Ground
LOAD
Multiple Remote Device/Switches
Load in between Master Device/Switch and Remote Device/Switch
Master Device/Switch Remote Device/Switch
Dimmed Hot
Neutral
Ground
Hot
Neutral
Ground
Traveler
Hot
Neutral
Ground
LOAD
Load after Remote Device/Switch and Master Device/Switch
Master Device/SwitchRemote Device/Switch
Hot
Neutral
Ground
Hot
Neutral
Ground
Dimmed Hot
Neutral
Ground
Traveler
LOAD
Master
Device/Switch
Figure 5 - Joiner Bar
Narrow/Narrow
Wide/Narrow Wide/Wide
Joiner Bar
Joiner Bar
3/4" space (use chase nipple)
3-1/2" deep
back box is
required
Four-gang wallbox Single-gang
wallbox
Fluorescent - 2 Wire Phase Control - 120-277VAC/VCA, 60HZ
Useonlyforcontrolofelectronicballastedluminaires.IntendedforAdvanceMark10,
LutronTu-Wire,orSylvaniaQuicktronicPowerSenseballasts.CAUTION:Toreduce
riskofoverheatingandpossibledamagetootherequipment,donotinstalltocontrola
receptacle,amotor-operatedappliance,oratransformersuppliedappliance.
Backbox - # Gangs
Wallplate Part #
Device Configuration
Backbox - # Gangs
Wallplate Part #
Device Configuration
Backbox - # Gangs
Wallplate Part #
Device Configuration
Backbox - # Gangs
Wallplate Part #
Device Configuration
Number & Type of NARROW
Number & Type of WIDE
0
1
2
3
0
4**
N+N+N
AWP00-30x
2
N*+*N
AWP00-20x
1
N
AWP0F-10x
1
6**
W+N+N+N
AWP00-31x
4
W+N*+*N
AWP00-21x
3
W+N
AWP0F-11x
1
W
AWP0F-01x
2
7
W+N*+N*+*N+W
AWP00-32x
6
W+N*+*N+W
AWP00-22x
5 or 6
W+N+W
AWP0F-12x
4
W+W
AWP0F-02x
3
9
W*+*W+N*+N*+*N+W
AWP00-33x
8
W*+*W+N*+*N+W
AWP00-23x
8
W+W+N+W
AWP0F-13x
6**
W+W+W
AWP0F-03x
Basic Configurations
Multi-Gang Installations:
Amulti-gangedinstallationexistswhenmultipledevicesareinstalledinthesame
backbox.Inmulti-ganginstallations,thefollowingmayberequired:
- Devicede-rating -Finremoval
- Useofjoinerbarsforadjacentdevices. - Backboxsize
NOTE: TEST FIT DEVICE INSTALLATION WITH THE WALL PLATE PRIOR TO BREAKING
FINS OR INSTALLING DEVICES TO ENSURE YOU UNDERSTAND ALL REQUIREMENTS.
BackBoxSize&JoinerBars:
Todeterminetherequiredback-boxsizeinmulti-ganginstallations,reference
tablebelow.Inapplicationswherethedevicesdonotlineupwithbackboxdevice
mountingholes,usejoinerbarstojointhecontrolstogether.ReferenceFigure 5.
De-ratings:
Whennsarebroken,somedevicesmustbede-rated.Referencetablebelowto
determinethedeviceratingswhen0,1,or2nsareremoved.
FinRemoval:
Whenitisdesiredtoinstalldevicesinassmallaspaceaspossible,allinsidensoflike
sized,adjacentdevicescanbebrokenoff.Figure 4showhowtobreakoffnsandthe
specicorderinwhichmultipledevicesmustbeinstalledinmulti-ganginstallations.
Figure4-FinRemoval
Back view of devices shown
Break off these fins
DO NOT Break off these fins
Break off these fins
Fin break off points
Fluorescent
2 Wire Phase Control
1500
12.5
3463
2875
1 fin
removed
600
5.0
1385
1150
780
6.5
1801
1495
1620
13.5
3740
3105
1224
10.2
2825
2346
840
7.0
1939
1610
1560
13.0
3601
2990
2 FINS
REMOVED
1476
12.3
3407
2829
636
5.3
1468
1219
1476
12.3
3407
2829
1044
8.7
2410
2001
1332
11.1
3075
2553
660
5.5
1524
1265
AWRMG-XA_
AWSMG-XA_
AWSMT-XA_
AWRMG-XB_
AWSMG-XB_
AWRMG-XC_
AWSMG-XC_
AWRMG-XD_
AWSMG-XD_
AWSMT-XB_
AWSMT-XC_
AWSMT-XD_
Amps
VA @ 120V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
Amps
VA @ 120V
VA @ 230V
VA @ 277V
0 fins
removed
1000
8.3
2308
1917
1920
16.0
4432
3680
1500
12.5
3463
2875
1000
8.3
2308
1917
1920
16.0
4432
3680
  • Page 1 1
  • Page 2 2

Leviton AWSMT-EBW Operating instructions

Leviton
Brand
Leviton
Model
AWSMT-EBW
Category
Motorcycle Accessories
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents