Leviton OSSNL-IDI Installation guide

Brand: Leviton

Model: OSSNL-IDI

Type: Installation guide

Leviton OSSNL-IDI is a single-pole designer wall switch occupancy sensor with an LED nightlight that automatically switches lights on and off based on motion detection. It features adjustable time-delay settings from 30 seconds to 2 hours and a fully adjustable LED nightlight with continuous or dim mode. Perfect for hospitality and healthcare facilities, it offers both auto ON and manual ON settings for added convenience.

Single Pole (One Location) or Multi-Location

Designer Wall Switch Occupancy Sensor with LED NightLight

California Title 24 2005 Compliant

Cat. No. OSSNL/OSSNL-INx/OSS10-IDx

No Minimum Load Required

Compatible with incandescent lamps, electronic and magnetic low-voltage ballasts, electronic and magnetic ballasts, and fans

INSTALLATION INSTRUCTIONS

Incandescent: 800W @ 120V Fluorescent: 1200VA @ 120V Fluorescent: 2700VA @ 277V Supplemental: 1/4hp @ 120V

PK-93369-10-00-0B

WARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.

• Controllingaloadinexcessofthespeciedratingswilldamagetheunitandposeriskofre,electricshock,personalinjuryordeath.

Checkyourloadratingstodeterminesuitabilityforyourapplication.

• Donotinstallthisunittocontrolareceptacle.

WARNINGS AND CAUTIONS:

• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.

• Donottouchthesurfaceofthelens.Cleanoutersurfacewithadampclothonly.

• TheOSSNL/OSSNL-INx/OSS10-IDxOccupancySensorisintendedtoreplaceastandardlightswitch.

• Usethisdevicewith copper or copper clad wire only.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER atcircuitbreakerorfuseandtestthat

power is off before wiring!

Step 1

/./&&

/./&&/./&&

/./&&

1- #12 w/ 1 to 3 #14, #16 or #18

2- #12 w/ 1 or 2 #16 or #18

1- #14 w/ 1 to 4 #16 or #18

2- #14 w/ 1 to 3 #16 or #18

WIRE NUT / # OF COND.

COMBINATION CHART

For non-standard wiring applications, refer

to Wire Nut and Conductor Size Chart

• Pulloffpre-cutinsulationfromsensorleads.

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.

Preparing and connecting wires:

5/8"

(1.6 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Step 3

Features

DESCRIPTION

LevitonCat.No.OSSNL/OSSNL-INx/OSS10-IDx,DesignerWall

SwitchOccupancySensorwithLEDNightLight,isdesignedto

detect motion from a heat-emitting source (such as a person

enteringaroom)withinitseld-of-view(monitoredspace)and

eitherautomaticallyormanuallyswitcheslightsONandOFF

(OSSNL-INx)ormanuallyswitcheslightsONandautomatically

switcheslightsOFF(OSS10).Thecontrolledlightswillremain

ONuntilnomotionisdetectedandthescheduledtime-delayhas

expired.TheLEDNightLightoperatesseparatelyfromcontrolled

roomlightsandwillturnONviaaphotocellwhentheambientlight

inthespaceisapproximatelylessthan1footcandleandturnOFF

whentheambientlightexceeds5footcandles.TheLEDNightLight

isadjustableforcontinuousmodeoradimmode.Inthedimmode

theLEDdimstoapproximately5%offullbrightnessafter2minutes

ofnooccupancy.WheninthemanualONswitchmode,theLED

NightLightwillfadeupandreturntotheadjustablesettingwhen

occupancyisdetectedandtheambientlightlevelpresenttothe

photocellislessthan1footcandle.TheLEDNightLightconsumes

lessthanonehalfofawattprovidingenergysavingsandguide

lightingwhenroomlightsareoff.TheLEDNightLightoutputisfully

adjustablewithasimpledialsetting.

OSSNL-IDxisperfectforuseinhospitalityandhealthcare

facilitieswitheitherautoONormanualONsettingswithadjustable

time-delaysettingsof30secondsto2hourswithLEDNightLight.

TheOSS10workswellanywhereamanualONonlyoccupancy

sensorwithLEDNightLightisdesiredandhasamaximumof

30minutetime-delaysettingtoconformtoCaliforniaTitle24

requirements.BothsensorsareULlistedandhavealimited5-year

warranty.

PASSIVE INFRARED (PIR) TECHNOLOGY DESCRIPTION

TheOccupancySensorsensesmotionwithinitscoverageareaof

1200sq.ftmaximumandcontrolstheconnectedlighting.Thisisa

self-containeddevicewhichprovidessensingandlightcontrol.The

OccupancySensorwillturnthelightsONwhenmotionisinitially

detected(OSSNL-INxOnly),andkeepthelightsONforaslong

asmotionisdetected.TheOSS10isamanualONdevicewith

automaticOFFwhennooccupancyisdetected.

TheOccupancySensorusesasmallsemiconductorheatdetector

thatresidesbehindamulti-zoneopticallens.ThisFresnellens

establishesdozensofzonesofdetection.TheSensorissensitive

totheheatemittedbythehumanbody.Inordertotriggerthe

Sensor, the source of heat must move from one zone of detection

toanother.Thedeviceismosteffectiveinsensingmotionacross

itseld-of-view,andlesseffectivesensingmotiontowardsoraway

fromitseld-of-view(refer to Field-of View diagrams).Keepthis

inmindwhenselectingtheinstallationlocation.

NOTE:Dresswireswithabendasshownindiagramtorelieve

stresswhenmountingdevice.

•

 Positionallwirestoprovideroominoutletwallboxfordevice.

• Partiallysecuredeviceusinglongmountingscrewsprovided.

• Restorepoweratcircuitbreakerorfuse.

• TheLEDindicatorwillashafterpowerisapplied.Allow

approximtely30secondsforcharge-up.After30secondsthe

lightswillturnON.IfthelightsturnONandtheLEDblinks

when a hand is waved in front of the lens, then the Sensor was

installedproperly.

If lights do not turn ON, refer to the TROUBLESHOOTING

section.

NOTE:Cat.No.OSSNL/OSSNL-INx/OSS10-IDxisfactory

presettoworkwithoutanyadjustments.Ifyoudesiretochange

thefactorysettings,refer to FEATURES AND SETTINGS

section).

NOTE:ToavoidPERMANENTDAMAGEtotheunit,becareful

NOTTOOVERTURNthecontrolknobsorleverswhensetting

theSensor.Thecontrolscanbeaccessedbyremovingthe

wallplate (if applicable) and control panel cover (refer to Sensor

Features Diagram).Useasmallstraightbladescrewdriverto

adjustknobsandblinderlevers.

NOTE: DO NOTpressinonblinderleversoruseexcessive

force (refer to Sensor Features Diagram).

•AttachtheControlPanelcoverwhenthedesiredsettingsare

complete.

FEATURES AND SETTINGS:

BLINDERS:Theblinderscannarrowtheeld-of-viewofthedevice

topreventunwantedactivationfromtrafcinadjacentspace.There

aretwoblinders,andeachoperateindependently.Tooperatethe

blinders,useangerorsmallscrewdrivertomovetheblinder

adjustmentleverstowardorawayfromthecenterofthedevice.

Theblinderleversarefoundabovethecontrolknobsandbelowthe

text‘BLINDERS’onthecontrolpanel.Withbothleversmovedfully

towardsthecenter,theeld-of-viewisnarrowedto32°.Withboth

leversmovedfullyawayfromthecenter,theeld-of-viewisata

maximum180°(refer to Sensor Features Diagram).

WIRING SENSOR:

Connect wires per WIRING DIAGRAM as follows:

Screwwireconnectoronclockwisemakingsuretherearenobare

conductorsbelowthewireconnectors.Secureeachconnectorwith

electricaltape.

• GreenorbarecopperwireinwallboxtoGreenlead.

• LineHotwallboxwiretoBlacklead.

• LoadwallboxwiretoBluelead.

• LineNeutralwallboxwiretoWhitelead.

NOTE: Allow approximately 30 seconds for warm-up after connected.

Black (Hot)

Neutral (White)

Load

Sensor

Black

White

Blue

Green

Ground

Line

120/277VAC, 60Hz

Sensor

Black

White

Blue

Green

Installing your Sensor -

Single-Pole Application:

NOTE: Sensor requires a neutral connection in order

tooperate.Usethegroundwireintheelectriclboxfor

groundconnection.Ifthereisnogroundwire,ensure

electricalboxisgroundedandattachgroundwiretobox

withascrew.

Step 4

INSTALLING YOUR SENSOR

NOTE:UsecheckboxeswhenStepsarecompleted.

Sensor 1

Black

White

Blue

Green

Sensor 2

Black

White

Blue

Green

Installing your Sensor -

3-Way Wiring Application:

NOTE: Sensor requires a neutral connection in order

tooperate.Usethegroundwireintheelectricalboxfor

groundconnection.Ifthereisnogroundwire,ensure

electricalboxisgroundedandattachgroundwiretobox

withascrew.

Step 5

Step 2

3-Way

1. Line or Load

(See *IMPORTANT instruction)

2. Neutral

3. Ground

4. FirstTraveler–notecolor

5. SecondTraveler–notecolor

Single-Pole

1.Line(Hot)

2.Neutral

3.Ground

4. Load

Identifying your wiring application

(most common):

NOTE:Ifthewiringinthewallboxdoesnotresemblethis

conguration,consultaqualiedelectrician.

*IMPORTANT:For3-Wayapplications,notethatoneofthescrew

terminalsfromtheoldswitchbeingremovedwillusuallybeadifferent

color(Black)orlabeledCommon.Tagthatwirewithelectricaltapeand

identifyasthecommon(LineorLoad)inbothswitchwallboxes.

NOTE: Sensor 1 mustbeinstalledinawallboxthathasbothaLINE

HotandaNeutralconnection.Sensor2mustbeinstalledinawallbox

thathasbothaLoadandaNeutralconnection.

Ifyouareunsureaboutanypartoftheseinstructions,consulta

qualiedelectrician.

WIRING SENSOR 1:

Connect wires per WIRING DIAGRAM as follows:

Screwwireconnectoronclockwisemakingsuretherearenobare

conductorsbelowthewireconnectors.Secureeachconnectorwith

electricaltape.

• GreenorbarecopperwireinwallboxtoSensor1Greenlead.

• LineHot(common)wallboxwireidentied(tagged)whenremoving

oldswitchandFirstTravelerfromSensor2toSensor1Blacklead.

• SecondTravelerwallboxwirefromSensor2toSensor1Bluelead.

• LineNeutralwallboxwiretoSensor1Whitelead.

WIRING SENSOR 2:

Connect wires per WIRING DIAGRAM as follows:

Screwwireconnectoronclockwisemakingsuretherearenobare

conductorsbelowthewireconnectors.Secureeachconnectorwith

electricaltape.

• GreenorbarecopperwireinwallboxtoSensor2Greenlead.

• Loadwallboxwireidentied(tagged)whenremovingoldswitch

andSecondTravelerfromSensor1toSensor2Bluelead.

• FirstTravelerLineHotfromSensor1toSensor2Blacklead.

• SecondTravelerwallboxwirefromSensor2toSensor1Bluelead.

• LineNeutralwallboxwiretoSensor2Whitelead.

NOTE: Allow approximately 30 seconds for warm-up after connected.

Black (Hot)

Neutral (White)

Load

Sensor 2Sensor 1

Black

White

Blue

White

Blue

Green

Ground

Green

Ground

Line

120/277VAC, 60Hz

Wall surface

Sensor

Mounting

screws

(2 places)

Testing your Sensor prior to completely

mounting in wall box:

Step 6

• Leviton’sDecora

styledesign

• WhiteLEDNightLightfunctionwithOccupancySensor

• NightLightActivateswhenLowAmbientLightPresent

• AdjustableNightLightLevels

• AutoON/OFF(OSSNL-INx)andManualON/AutoOFF(OSS10)

DESCRIPTION cont'd

Notethatoccupancysensorsrespondtorapidchangesin

temperature,socareshouldbetakennottomountthedevice

nearaclimatecontrolsource(i.e.radiators,airexchanges,andair

conditioners).Hotorcolddraftswilllooklikebodymotiontothedevice

andwilltriggeritiftheunitismountedtooclose.Itisrecommended

tomounttheOccupancySensoratleast6ft.awayfromtheclimate

controlsource.Thedevicecanbemountedinasinglegangwallbox.

Inaddition,itisalsorecommendedNOTtomounttheOccupancy

Sensordirectlyunderalargelightsource.Largewattagebulbs

(greater than 100W incandescent) give off a lot of heat and switching

thebulbcausesatemperaturechangethatcanbedetectedbythe

device.MounttheOccupancySensoratleast6ft.awayfromlarge

bulbs.Ifitisnecessarytomountthedevicecloser,lowerthewattage

ofthebulbdirectlyoverhead.

Slotted/PhillipsScrewdriver ElectricalTape Pliers

Pencil   Cutters  Ruler

Tools needed to install your Sensor

Insertwires

straight

then twist

clockwise

Electrical

Tape

Insertwires

straight

then twist

clockwise

Electrical

Tape

OPERATION

PUSH-BUTTON:Cat.No.OSSNL/OSSNL-INx/OSS10-IDxhasa

push-button switch that toggles the lights (refer to gure).Ifthe

lightsareOFF,thelightswillturnONwhenthebuttonispressed,and

remainONinthepresenceofmotion.Intheabsenceofmotion,the

SensorUnitwilltime-outandturnthelightsOFF.

IfthelightsareON,thelightswillturnOFFwhenthebuttonispressed.

ThelightswillstayOFFregardlessofmotiondetected,untilthetime-

outexpires.Afterthetime-outexpires,thelightswillturnON(Auto-ON

Modeonly)withthenextdetectedmotion.Thisisusefulforslideor

lmpresentations.

NOTES:

• TheMotionIndicatorLEDwillblinkevery2secondswhilemotionis

detected.

• InManual-ONmode,thebuttonmustbepressedtoturnthe

lightsON.

PRODUCT INFORMATION

• Fortechnicalassistancecontactusat1-800-824-3005

• Visitourwebsiteatwww.leviton.com

PK-93369-10-00-0B

Field-of-View (Horizontal)

20 ft (6.1 m)

small motion

30 ft (9.1 m)

20 ft (6.1 m)

small motion

40 ft

(12.2 m)

Side (Vertical) Field-of-View

27 ft.

(8.2 m)

38 ft.

(11.7 m)

4 ft.

(1.2 m)

4.5 ft.

(1.4 m)

8.3

Sensor Unit

• Securedevicebyrmlytighteningmountingscrews.

• InstallDecora

stylewallplate(soldseparately).

Sensor and Wallplate Mounting:

Step 7

Wall surface

Device mounting screw

(2 places)

Wallplate

mounting

screw

(2 places)

Sensor Features Diagram

Lens with

PIR and LED

NightLight

Blinders

Control Panel

Cover

Push Button

LED

Indicator

Step 6 cont’d

Testing your Sensor prior to

completely mounting in wall box:

FEATURES AND SETTINGS:

TIME-DELAY:Cat.No.OSSNL/OSSNL-INx/OSS10-IDxwillturn

lightsONwhenmotionisdetected.Whenmotionisnolonger

detected,theSensorUnitwillwaitacertainamountoftimeand

thenturnthelightsOFF.Thiswaittimeiscalled‘time-out’.

The“time-out”isselectedfromfour(4)presetvalues.Pointingthe

arrowatoneofthemarkingsonthefacechoosesthevalueoftime.

ThebuttonLEDindicatorlightwillashtwicewhenthetimesetting

haschanged.Thefollowingselectionsareavailable:

OSSNL-IDx: Face Marking Value of Time

NOTE:The“time-out”isfactorypresettothirty(30)minutes

(refer to Sensor Features Diagram).

NOTE: All time durations mentioned in the instructions are

approximatewithin10seconds.

OSS10-IDx: Face Marking Value of Time

NOTE: The“time-out”isfactorypresettoten(10)minutes

(refer to Sensor Features Diagram).

NOTE: All time durations mentioned in the instructions are

approximatewithin10seconds.

RANGE:Todecreasedetectionrangeandsensitivity,rotatethe

knobcounter-clockwise(refer to Sensor Features Diagram).The

detectionsrangecanbeadjustedfrom100%downto35%.

MANUAL-ON MODE (OSSNL-INx ONLY):Thefactorydefault

settingfortheOSSNLisManual-ON.Tochangethissettingto

Auto-ON/OFF,turnthedialmarked“ONMODE/NLDIM”clockwise

anywhereintotheareathatindicates“AUTO”.Toreturnto

Manual-ON,turnthedialcounter-clockwiseanywhereintothearea

thatindicates“MAN”.

NOTE:OSS10isaManual-ONsettingonly.

NIGHTLIGHT:TheOSSNL/OSSNL-INx/OSS10-IDxrespondsto

theambientlightlevelpresentinaroom.TheOSSNL/OSSNL-INx/

OSS10-IDxusesaninternalphotocelltodetectwhentheambient

lightlevelisapproximatelylessthan1footcandleactivatingthe

LEDNightLight.Further,theinternalphotocellwillturnOFFthe

LEDNightLightwhenitdetectsanambientlightlevelover5foot

candles.TheLEDNightLighthasadjustablelightoutputtomeetthe

needs of the space and can be set to for continuous mode or dim

modewhichwillautomaticallydimto5%offullbrightnessafter2

minutesofnooccupancy.

NIGHTLIGHT DIM:ToadjusttheLEDNightLightoutput,turnthe

dialmarked“ONMODE/NLDIM”(OSSNL-INx)or“NITELITEDIM”

(OSS10)counter-clockwisetodecreaseandclockwisetoincrease

lightoutput.

NIGHTLIGHT MODE:Thefactorydefaultsettingforthe

NightLightModeisdimmedmode.ThismeanstheLEDNightLight

automaticallydimsto5%offullbrightnessafter2minutesofno

occupancywhenactivatedbytheinternalphotocell.Tochangethe

NightLightModeperformthefollowingprocedure:

1. Press and hold the push button for 2 seconds to determine the

currentmode.

a. NightLightashesonceevery1secondforContinuousMode

untilthebuttonisreleased.

b. NightLightashestwiceevery1secondforDimModeuntil

thebuttonisreleased.

2.Tochange,holdthepushbuttonfor10secondsandtheMode

willtoggle.Thiswillbeindicatedbyachangeintheashpattern

asdescribedabove.

TROUBLESHOOTING

1.Ifthereisnoresponsefromtheunit(thelightneverturnsONand

theLEDneverblinks)11/2minutesafterpowerisapplied,then

uninstalldeviceandverifythereisagroundconnectionatthe

wallbox.Ifthereisagroundconnection,verifywiring.

2.IfthelightsneverturnON,buttheLEDblinks,checkifthe

Manual-ONsetting(OSSNLonly).SeeManual-ONModesettingfor

adjustments.

3.IfthelightsconstantlystayON,evenwhentheroomisunoccupied:

A.ChecktheTimesetting.Seehowthistimecomparestohow

longthelightsstayON.

B.TryloweringtheRangeControl.Rotatetheknobcounter-

clockwiseabout30°.

C.Iftheproblempersists,tryreducingagain.

NOTE:DoNotreducesomuchthatCat.Nos.

OSSNL/OSSNL-INx/OSS10-IDxcannotseenormaloccupancy.

D.BesuretousetheBlinderstoblockanyunwanted

hallwaytrafc.

E.Checkforreectedheat/motionasSensorUnitmaybeseeing

motionthroughawindow.

F. CheckforadjacentHVACand/orheaterducts.

NOTES

Cat. No. OSSNL

T IM E

ON MODE/NL DIM

MAN

AUTO

RANGE

Blinder adjustment levers

BLINDERS

Control Panel Cover

30M

30S

Cat. No. OSS10

TIME

NITELITE DIM

MIN MAX

Blinder adjustment levers

BLINDERS

Control Panel Cover

10M

30S

20M

30M

RANGE

30S

30M

30secondxedtime-outforperformingawalktest

30 minute time-out

1 hour time-out

2 hour time-out

Value of TimeFace Marking

30S

10M

20M

30M

30secondxedtime-outforperformingawalktest

10 minute time-out

20 minute time-out

30 minute time-out

Value of TimeFace Marking

FCC COMPLIANCE STATEMENT

ThisdevicecomplieswithPart15oftheFCCRules.Operationis

subjecttofollowingtwoconditions:(1)thisdevicemaynotcause

harmfulinterference,and(2)thisdevicemustacceptanyinterference

received,includinginterferencethatmaycauseundesiredoperationof

thedevice.

Thisequipmenthasbeentestedandfoundtocomplywiththelimits

foraClassBDigitalDevice,pursuanttoPart15oftheFCCRules.

Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipment

generates,uses,andcanradiateradiofrequencyenergyand,ifnot

installedandusedinaccordancewiththeinstructions,maycause

harmfulinterferencetoradiocommunications.However,thereisno

guaranteethatinterferencewillnotoccurinaparticularinstallation.If

this equipment does cause harmful interference to radio or television

reception,whichcanbedeterminedbyturningtheequipmentOFFand

ON,theuserisencouragedtotrytocorrecttheinterferencebyoneor

moreofthefollowingmeasures:

• ReorientorrelocatethereceivingAntenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthat

towhichthereceiverisconnected.

• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.

FCC CAUTION

AnychangesormodicationsnotexpresslyapprovedbyLeviton

ManufacturingCo.,Inc.,couldvoidtheuser'sauthoritytooperatethe

equipment.

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenefitofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforfiveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchfiveyearperiodtheproductisreturnedprepaid,with

proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,

abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandfitnessfora

particularpurpose,islimitedtofiveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

Leviton OSSNL-IDI Installation guide

Leviton OSSNL-IDI Installation guide

Leviton OSSNL-IDI Installation guide

Related papers

Other documents