Step 4 — Switched Optical Output
Connect a ber cable between the Output LC connector on the FOX switcher (the left-hand connector on transceiver block 8) and a
compatible receiver.
NOTE: For HDCP compliance in a system with FOX or PowerCage FOX HDMI extenders:
z Connect the Loop LC connectors (
c
) on inputs 1 through 7 to the Rx LC connector on the connected transmitters.
z Connect the Input connector (
a
) on input 8 to the Tx LC connector on the receiver.
100-240V 0.3A
50/60 Hz
RS-232
Tx Rx
FOX SW8
OPTICAL INPUTS
LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN LOOP IN OUTIN
12345678
FOXBOX Tx HDMI #1
12V
1.0A MAX
POWER
FOXBOX Tx HDMI
AUDIO INPUT
RS-232
OVER FIBER
ALARM
Tx Rx 1 2
HDMI INPUT
LINK
OPTICAL
RxTx
LINK
FOXBOX Tx HDMI #7
FOXBOX Rx HDMI
12V
1.0A MAX
POWER
FOXBOX Tx HDMI
AUDIO INPUT
RS-232
OVER FIBER
ALARM
Tx Rx 1 2
HDMI INPUT
LINK
OPTICAL
RxTx
LINK
Transmitters 3 — 6
• • • • • • •
12V
1.0A MAX
POWER
FOXBOX Tx HDMI
AUDIO INPUT
RS-232
OVER FIBER
ALARM
Tx Rx 1 2
HDMI INPUT
LINK
OPTICAL
RxTx
LINK
12V
1.0A MAX
POWER
LINK
OPTICAL
RxTx
LINK
HDMI AUDIO
HDMI
AUDIO
OUTPUTS
OFF
ON
REMOTE
RS-232
Tx Rx
RS-232
OVER FIBER
ALARM
Tx Rx 1 2
LR
FOXBOX Rx HDMI
3 3 3
1
Step 5 — Remote Control Connections
Do not tin the wires!
Controlling
Device
Gnd ( )
Rx
Tx
Ground ( )
Receive (Rx)
Transmit (Tx)
Bidirectional
RS-232
Tx Rx
FunctionPin
Tx
Rx
Transmit data
Receive data
Signal ground
z Connect a host device to the rear panel RS-232 port. See the drawing at right to make the
connection.
z Connect a host device to the front panel Config(uration) port, a mini USB port.
Step 6 — Power
Plug a standard IEC power cord between the power connector and a 100 VAC to 240 VAC,
50-60 Hz power source.
Operation — Select an input
Press and release an input button to select that input. The lit button indicates the selected input.
Selected SIS Commands
The table below is a partial list of SIS commands that you can use to operate the switcher. For a complete listing, see the
FOX SW8 User Guide. Issue the commands from a PC connected to the RS-232 port or the Conguration (USB) port.
Command
ASCII Command
(Host to Unit)
Response
(Unit to Host)
Additional Information
Select an input
X!
!,
X!
&, or
X!
% In
X!
•All (or RGB or Vid)
] X!
= input number. !, &, and % can be used interchangeably.
Show input selection
!, &, or %
X!] X!
= input number. !, &, and % can be used interchangeably.
Mute or unmute the output
X@
B Vmt
X@] X@
= 0 (mute off) or 1 (mute on).
Show mute status
B
X@] X@
= 0 (mute off) or 1 (mute on).
Set input reclocker mode
X#
= Rte
X#] X#
= 00 (bypass), 01 (1.25 Gbps), 02 (2.125 Gbps), or 03 (4.25 Gbps).
Show reclocker mode
=
X#] X#
= 00 (bypass), 01 (1.25 Gbps), 02 (2.125 Gbps), or 03 (4.25 Gbps).
Lock and unlock front panel
X$
X Exe
X$] X$
= 0 (unlocked) or 1 (locked).
Show lock status
X
X$] X$
= 0 (unlocked) or 1 (locked).
Reset whole switcher
E
ZXXX
}
Zpx
]
Unmute the output, unlock the front panel, and select input 1.
] = Carriage return/line feed } = Carriage return (no line feed) • = space E = Escape key
68-1550-51
Rev. B
04 13
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
FOX SW8 • Setup Guide (Continued)