2. Extron
  3. AVEdge 100
AVEdge 100

Extron AVEdge 100 User manual

  • Hello! I am an AI chatbot trained to assist you with the Extron AVEdge 100 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the Extron AVEdge 100?
    What are the installation requirements?
    How do I prepare the AVEdge 100?
    How do I install Retractors?
    How do I route and connect cables?
1
IMPORTANT:
Go to www.extron.com for the
pr
oduct specifications
.
Kit Contents
AVEdge 100 • Installation Guide
This guide provides instructions for an experienced installer to install and connect the
Extron AVEdge 100 Cable Access Enclosure.
The AVEdge 100 enclosure can be mounted to the edge of a table for cable
access, connections, and AC power. It is designed for semi-permanent
environments and applications where tables cannot be modied.
Installation Overview:
Planning (page 2)
Check with local and state regulations before starting the installation.
Check all parts and equipment before installation.
Determine the best location for the enclosure.
Preparing the AVEdge 100 (page 3)
Assemble and install the connectivity modules or Retractor trim.
Install an optional ZipClip and a ZipClip compatible device (page 4)
Mounting the AVEdge 100 (page 5)
Mount the AVEdge 100 on the edge of the table.
Installing Retractors (page 5)
Install Retractors in the AVEdge 100.
Routing and Connecting Cables (page 6)
Manage cables and connect to the AV system.
Hole Plugs
3/8" (6), 1/4" (2)
Connectivity Bracket (2)
with #6-32 Bracket Screws (4)
Cable Grommet Plate (2)
AAP Frame Plate (2)
Retractor Trim (1)
and #6 Screws (2)
Retractor Pin & Clip
#4-40 Plate Screws (8)
ZipClip Screws (2)
and Washers (2)
Optional Accessories:
AVEdge 100
ZipClip 100
ZipClip 20
0
“Show Me” Cable Trim Plate (2)
AVEdge 100 • Installation Guide (Continued)
2
17.26"
(43.8 cm)
8.65"
(22.0 cm)
Horizontal Mounting
22.61"
(57.4 cm)
Vertical Mounting
23.77"
(60.4 cm)
20.49"
(52.0 cm)
8.67"
(22.0 cm)
Horizontal Mounting
28.61"
(72.7 cm)
Vertical Mounting
26.14"
(66.4 cm)
11.0"
(27.9 cm)
Angular Mounting
30
XL Models
XL Models
13.98"
(35.5 cm)
Planning
Read the following information before installing the AVEdge 100.
Check with Local and State Regulations Before Starting the Installation:
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check All Parts and Equipment Before Installation:
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Determine the Best Location for the Enclosure:
Ensure that the location where the AVEdge 100 is to be installed is convenient for as many users as possible.
Ensure that there is ample space under the table for the AVEdge 100 mounting clamps and for cable management.
Ensure that there is enough space for the Retractor assembly under the table or furniture, if using Retractors. See
dimensions for the Retractors below.
NOTES:
• To prevent objects from impeding cable retraction, ensure at least 3 inches of clearance from the exposed cable side of
the enclosure. See the diagrams below.
• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or
entanglement (see Routing and Connecting Cables on page 6).
3
Preparing the AVEdge 100
Step 1 — Assemble and install the connectivity modules or Retractor trim.
Connectivity modules allow you to populate the AVEdge 100 with a combination of AAPs, cable pass-through plates, or
Retractors. Follow the steps below to install the module of your choice or the Retractor trim, if using Retractors.
To assemble the AAP module or Cable Pass-Through module, use the included connectivity bracket as shown below.
AAP Module
Cable Pass-Through Module
NOTE: The modules can be installed on the
left or right side of the enclosure, but the
Retractor trim can only be installed on the
right.
#4-40 Nut with
Captive Washer
Secure up to two single-space
AAPs in the AAP plate.
1
Secure the AAP plate on the
connectivity bracket.
3
Insert cables thr
ough the bottom
of the connectivity bracket.
Connect cables to the AAPs.
2
#4-40 Plate
Screws
1/4" Hex Nut Driver
Insert cables thro
ugh
the bottom of the
connectivity bracket
and into the holes of
the grommet plate.
1
Snap the included
hole plugs into any
unused holes.
3
Secure the cable grommet
plate on the connectivity
brackets, using two of the
provided plate screws.
2
#4-40 Plate
Screws
Attach the module
using the included
bracket screws.
Insert the module into the
enclosure from the top.
4
5
#6-32
Bracket
Screws
NOTE: The bracket is intended to be used with UL Listed Extron ITE equipment.
Run the “Show Me”
cables through the
enclosure and insert
them into the
cable grommet plate.
1
Attach the “Show Me”
cable trim plate to
the top of the module,
using the module
screws.
2
Attach the cable gr
ommet
plate to the bottom
of the module, using
the module screws.
3
Insert the module
into the enclosure.
Attach the module
using one bracket
screw on the
top hole only.
4
For “Show Me” Cables:
4
AVEdge 100 • Installation Guide (Continued)
Step 2 (Optional) — Install an pptional ZipClip and a ZipClip compatible device.
Determine which ZipClip to use (depending on the device) and in which orientation (vertical or horizontal). Plan and ensure that
there is ample space for the device and its cables.
Vertical Mounting
ZipClip 100 only
Horizontal Mounting
ZipClip 100 or ZipClip 200
Use the provided ZipClip screws and
washers to mount the ZipClip to the
AVEdge 100.
OR
1
Attach the device to the ZipClip
(see the instructions included with
your ZipClip compatible device for
detailed instructions).
2
Use the provided ZipClip screws and
washers to mount the ZipClip to the
AVEdge 100.
OR
1
Attach the device to the ZipClip
(see the instructions included with
your ZipClip compatible device for
detailed instructions).
2
NOTE: If using Retractors, the ZipClip cannot be
mounted in the horizontal orientation.
Retractor Trim
For Retractors, install the Retractor trim
as shown at right.
Trim PieceTri
Insert the Retractor trim into the
right side of the enclosure.
1
Secure the Retractor trim
using two of the provided
#6 screws.
2
#6
Retractor
Screws
ure the Retractor trim
n
g two o
f
t
h
e prov
id
e
d
s
crews.
#
6
R
etractor
S
crew
s
5
Mount the AVEdge 100 on the edge of the table as shown below.
Installing Retractors
Install up to three Retractors in the Retractor trim as shown below. For horizontal or angular Retractor mounting, see below, and
then install the Retractors.
Mounting the AVEdge 100
Under the table, turn both screw clamps
and tighten them snugly to secure the enclosure.
Ensure that the AVEdge 100 is firmly secured to
the furniture.
2
1
Hold the assembled
AVEdge enclosure
onto the edge of the
table.
Under
the
table
,
turn
both
screw
clamps
a
nd tighten them snugly to secure the enclosure
.
E
nsure that the AVEd
g
e 100 is firml
y
secured to
thefurniture
em
os
e
o
Underthe tableturnbothscrew clamps
2
mb
l
ed
s
ure
o
f the
Angular Mounting
Remove the orientation screws as shown above, and then
follow this step:
Horizontal Mounting
Remove these orientation screws
(front and back), and then mount the
Retractors as shown on the right.
Cable Stop
Assembly
Move the cable stop assembly upward until
the angular mounting hole is visible.
Reinstall the orientation screws in this hole
(both sides).
Remove these orientation screws
(front and back), and then mount the
Retractors as shown on the right.
Cable Stop
Assembly
Move the cable stop assembly upward until
the angular mounting hole is visible.
Reinstall the orientation screws in this hole
(both sides).
See the Cable Retractor Series/2 Installation Guide,
available online at www.extron.com, for additional steps.
1
1
Insert the
Retractors
into the
Retractor trim.
1
Insert the pin through the Retractor
mounting hole on the side of the AVEdge
and through the Retractor assembly.
On the other side, secure the clip on the
pin.
2
Secure the locking
screws on the other
side of the Retractors.
Do not overtighten.
Other Side of Retractor
Assembly
Pin
Clip
3
6
68-2796
-01
Rev. B
02 16
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. www.extron.com
Routing and Connecting Cables
Organize and connect cables as shown below.
1
3
Secure cables with zip
ties to the rectangular
holes at the bottom of
the AVEdge.
For cable pass-through
applications, allow at
least 36 inches (0.9 m) of
cable loop for each cable.
Connect cables to the AV system and
connect the AC power cord if using a
power module.
2
AVEdge 100 • Installation Guide (Continued)
/