H3C LSQM1WCMB0 Configuration manual

H3C WX Series Access Controllers

Access Controller Module Configuration Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Document Version: 6W105-20101124

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT,

XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co.,

Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface

The H3C WX series documentation set describes the software features for the H3C WX Series Access

Controllers and guides you through the software configuration procedures. The configuration guides

also provide configuration examples to help you apply the software features to different network

scenarios.

The Access Controller Module Basic Configuration Guide describes the compatibility matrix between

access controller modules and Ethernet switches, and describes the basic configurations for an access

controller module to cooperate with an Ethernet switch.

This preface includes:

z Audience

z Conventions

z About the H3C WX Series Documentation Set

z Obtaining Documentation

z Technical Support

z Documentation Feedback

Audience

This documentation is intended for:

z Network planners

z Field technical support and servicing engineers

z Network administrators working with the WX series

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

italic

Italic text represents arguments that you replace with actual values.

[ ]

Square brackets enclose syntax choices (keywords or arguments) that are

optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars,

from which you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical

bars, from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by

vertical bars, from which you select at least one.

Convention Description

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by

vertical bars, from which you may select multiple choices or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&)

sign can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface.

For example, the

New User

window appears; click

OK

.

>

Multi-level menus are separated by angle brackets. For example,

File

>

Create

>

Folder

.

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause bodily

injury.

Means reader be careful. Improper operation may cause data loss or damage to

equipment.

Means an action or information that needs special attention to ensure

successful configuration or good performance.

Means a complementary description.

Means techniques helpful for you to make configuration with ease.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router

that supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, an access controller module, or a switching

engine on a unified switch.

Represents an access point.

Represents a mesh access point.

Convention Description

Represents omnidirectional signals.

Represents directional signals.

About the H3C WX Series Documentation Set

The H3C WX series documentation set includes:

Category Documents Purposes

WX3000 Series Unified Wired and Wireless

Switches Brochure

WX5000 Series Access Controllers Brochure

Product

description and

specifications

WX6000 Series Access Controllers Brochure

Describe product specifications and

benefits.

LSWM1WCM10 Access Controller Module

Card Manual

LSWM1WCM20 Access Controller Module

Card Manual

LSRM1WCM2A1 Access Controller Module

Card Manual

Provide the hardware specifications of the

cards, and describe how to install and

remove the cards.

LSQM1WCMB0 Access Controller Module

Installation Manual

Hardware

specifications

and installation

LSBM1WCM2A0 Access Controller Module

Installation Manual

Guide you through hardware

specifications and installation methods to

help you install your AC.

WX Series Access Controllers Getting Started

Guides

Guide you through the main functions of

your AC, and describes how to install and

log in to your AC, perform basic

configurations, maintain software, and

troubleshoot your AC.

WX Series Access Controllers Configuration

Guides

Describe software features and

configuration procedures.

WX Series Access Controllers Command

References

Provide a quick reference to all available

commands.

Software

configuration

WX Series Access Controllers Web-based

Configuration Guides

Describes configuration procedures

through the web interface.

WX3000 Series Unified Switches Release

Notes

WX5002 Series Access Controllers Release

Notes

WX5004 Series Access Controllers Release

Notes

Operations and

maintenance

WX6103 Series Access Controllers Release

Notes

Provide information about the product

release, including the version history,

hardware and software compatibility

matrix, version upgrade information,

technical support information, and

software upgrading.

Obtaining Documentation

You can access the most up-to-date H3C product documentation on the World Wide Web at

http://www.h3c.com

.

Click the links on the top navigation bar to obtain different categories of product documentation:

[Technical Support & Documents > Technical Documents]

– Provides hardware installation, software

upgrading, getting started, and software feature configuration and maintenance documentation.

[Products & Solutions]

– Provides information about products and technologies, as well as solutions.

[Technical Support & Documents > Software Download]

– Provides the documentation released with

the software version.

Technical Support

customer_service@h3c.com

http://www.h3c.com

Documentation Feedback

You can e-mail your comments about product documentation to [email protected].

We appreciate your comments.

z Read Compatibility Matrixes before using an H3C WX series access controller.

z Support of the H3C WX series access controllers for features and commands may vary by AC

model. For more information, see “Feature Matrixes” and “Command Matrixes” in Compatibility

Matrixes.

z The term AC in this document refers to H3C access controllers, access controller modules, and

H3C WX series unified switches' access controller engines.

z The interface types and the number of interfaces vary by AC model.

z The models listed in this manual are not applicable to all regions. Please consult your local sales

office for the models applicable to your region.

i

Table of Contents

1 Applicable Models and Software Versions·····························································································1-1

2 Typical Network Scenarios·······················································································································2-1

AC Networking········································································································································2-1

Access Controller Module Networking····································································································2-1

Unified Switch Networking ······················································································································2-2

3 Feature Matrixes········································································································································3-1

Feature Matrix for the WX5000 Series····································································································3-1

Feature Matrix for the WX6000 Series····································································································3-7

Feature Matrix for the WX3000 Series··································································································3-11

4 Command Matrixes····································································································································4-1

Command Matrix for the WX5000 Series·······························································································4-1

Command Matrix for the WX6000 Series·····························································································4-15

Command Matrix for the WX3000 Series·····························································································4-24

5 Access Controller Module Basic Configuration·····················································································5-1

Access Controller Module and Ethernet Switch Compatibility Matrix·····················································5-1

6 Access Controller Module Basic Configuration·····················································································6-1

Access Controller Module Basic Configuration·······················································································6-1

Configuring the Internal Ports of the Switch····················································································6-1

Configuring the Access Controller Module······················································································6-2

Configuration Examples··························································································································6-3

Configuring LS8M1WCMA0············································································································6-3

Configuring LSQM1WCMB0, LSBM1WCM2A0, or LSRM1WCM2A1············································6-3

Configuring LSWM1WCM20 or LSWM1WCM10············································································6-4

7 Index ···························································································································································7-1

1-1

1 Applicable Models and Software Versions

H3C WX series access controllers include the WX3000 series unified switches, and WX5000 and

WX6000 series access controllers. Table 1-1

shows the applicable models and software versions.

Table 1-1 Applicable models and software versions

Model Software version

WX3024 unified switches

WX3010 unified switches

WX3008 unified switches

LSWM1WCM20 access controller module

WX3000-CMW520-R3111P03

WX5002 access controller

LS8M1WCMA0 access controller module

WX5002-CMW520-R1112

WX5002V2 access controller

WX5004 access controller

LSWM1WCM10 access controller module

WX5004-CMW520-R2107P04

WX6103 access controller

LSQM1WCMB0 access controller module

LSBM1WCM2A0 access controller module

LSRM1WCM2A1 access controller module

WX6103-CMW520-R2115P08

2-1

2 Typical Network Scenarios

AC Networking

As shown in the following figure, the AC is connected to Switch (Layer 2 or Layer 3) through GE1/0/1,

which can be connected to APs directly or connected to APs over an IP network. Clients can be

connected to the network through the APs to implement WLAN user access.

Figure 2-1 AC networking

AC

GE 1/0/1

Server

AP 1 AP 2

Client A Client B

Scheme 1

IP network

Access Controller Module Networking

As shown in the following figure, installed with an access controller module, Switch (Layer 2 or Layer 3)

can be connected to APs directly or connected to APs over an IP network. Clients can be connected to

the network through the APs to implement WLAN user access.

2-2

Figure 2-2 Access controller module networking

Unified Switch Networking

As shown in Figure 2-3, Unified switch (functions as both an AC and a Layer 2 switch) can be connected

to APs directly or connected to APs over an IP network. Clients can be connected to the network

through the APs to implement WLAN user access.

Figure 2-3 Unified switch networking diagram

3-1

3 Feature Matrixes

In this document, Yes means a feature or command is supported, and No means not supported.

Feature Matrix for the WX5000 Series

The LS8M1WCMA0, LSWM1WCM10, and LSWM1WCM20 on the WX5000 series adopt the OAP architecture. Installed on the expansion slots of switches,

they work as OAP cards to exchange data and status and control information with the switches through their internal service interfaces. Do not configure

services such as QoS rate limiting and 802.1X authentication on GE interfaces on the LS8M1WCMA0, XGE 1/0/1 on the LSWM1WCM10, and the logical

interface BAGG1 aggregated by GE 1/0/1 and GE 1/0/2 on the LSWM1WCM20.

Table 3-1 Feature matrix for the WX5000 series

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

AUX user interface Yes No Yes No Yes Yes

Console user interface No Yes No Yes No No

Login configuration

Telnet Yes Yes Yes Yes Yes Yes

Fundamentals

Configuration

Guide

User interface

configuration

User interface type

Console

user

interface not

supported

AUX user

interface not

supported

Yes

AUX user

interface

not

supported

Console user

interface not

supported

Console user

interface not

supported

3-2

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

File system

management

configuration

Configuration file

encryption

No No No No No Yes

Storage media

supported

Flash CF Flash CF CF Flash

Device management

configuration

License

Supports 32

concurrent

APs by

default, and

can be

extended to

support 64.

No on the

WX5002-12

8

Supports 32

concurrent

APs by

default, and

can be

extended to

support 64.

No

Supports

64

concurren

t APs by

default,

and can

be

extended

to support

256.

Supports 64

concurrent APs

by default, and

can be extended

to support 256.

Supports 32

concurrent APs

by default, and

can be extended

to support 128.

Hot AC backup No Yes No Yes Yes No

WLAN

Configuration

Guide

WLAN services

configuration

Maximum number of

SSIDs supported

128 256 128 256 256 128

Combo port

configuration

Yes Yes No Yes

No No

Shutting down an

Ethernet interface

Yes Yes Yes Yes

Yes.

Do not use the

shutdown

command on

internal

interfaces;

otherwise, the

normal

operation of the

device will be

affected.

Yes.

Do not use the

shutdown

command on

internal

interfaces;

otherwise, the

normal

operation of the

device will be

affected.

Layer 2 – LAN

Switching

Configuration

Guide

Ethernet interface

configuration

Configuring flow

control on an Ethernet

interface

Yes Yes Yes Yes

No No

3-3

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

Configuring loopback

detection on an

Ethernet interface

Yes on GE

interfaces

only

Yes on GE

interfaces

only

Internal loopback

testing supported

on GE interfaces

only

Yes on

GE

interfaces

only

Internal

loopback testing

supported on

XGE interfaces

only

Internal

loopback testing

supported on

GE interfaces

only

Link aggregation

configuration

Link aggregation Yes Yes No Yes No Yes

MSTP Configuration STP No Yes No Yes No No

Layer 2 forwarding

configuration

Layer 2 forwarding Yes No Yes No No No

Port mirroring

configuration

Port mirroring

Remote port

mirroring

and

cross-board

mirroring not

supported

Remote port

mirroring

and

cross-board

mirroring not

supported

No

Remote

port

mirroring

and

cross-boa

rd

mirroring

not

supported

No No

DNS configuration

IPv6 DNS

configuration

Yes Yes Yes Yes Yes Yes

IP performance

optimization

configuration

Configuring ICMP to

send error packets

Yes No No No No No

Adjacency table

configuration

Displaying and

maintaining adjacency

table

No Yes No Yes Yes Yes

IPv6 basics

configuration

IPv6 basics

configuration

Yes Yes Yes Yes Yes Yes

Layer 3 – IP

Services

Configuration

Guide

IPv6 application

configuration

IPv6 application

configuration

Yes Yes Yes Yes Yes Yes

Layer 3 – IP

Routing

IP routing basics

configuration

IPv6 features Yes Yes Yes Yes Yes Yes

3-4

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

Configuration

Guide

IPv6 static routing

configuration

IPv6 static routing

configuration

Yes Yes Yes Yes Yes Yes

MLD snooping

configuration

MLD snooping Yes Yes Yes Yes Yes Yes

IP Multicast

Configuration

Guide

IPv6 multicast VLAN

configuration

IPv6 multicast VLAN Yes Yes Yes Yes Yes Yes

ACL configuration IPv6 ACL Yes Yes Yes Yes Yes Yes

Configuring line rate Yes Yes Yes Yes Yes Yes

ACL and QoS

Configuration

Guide

QoS

Configuring CAR

applicable to all traffic

of online users

No Yes No Yes Yes Yes

AAA

Specifying the device

ID to be used in

stateful failover mode

No Yes No Yes Yes No

Configuring Layer 3

portal authentication

No Yes No Yes Yes Yes

Specifying the portal

group to which the

portal service backup

interface belongs

No Yes No Yes Yes No

Specifying the device

ID to be used in

stateful failover mode

No Yes No Yes Yes No

Portal configuration

Specifying the backup

source IP address for

RADIUS packets to be

sent

No Yes No Yes Yes No

Security

Configuration

Guide

SSH2.0 configuration

Specifying a source

IPv6 address or

interface for an SSH

client

Yes Yes Yes Yes Yes Yes

3-5

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

Establishing a

connection between

an SSH client and an

IPv6 SSH server

Yes Yes Yes Yes Yes Yes

Specifying a source

IPv6 address or

interface for an SFTP

client

Yes Yes Yes Yes Yes Yes

Establishing a

connection between

an SFTP client and an

IPv6 SFTP server

Yes Yes Yes Yes Yes Yes

IPv6 SFTP client Yes Yes Yes Yes Yes Yes

Security protection

configuration

Management protocol

packets supported

Telnet,

SNMP, and

web

managemen

t packets

whose

destination

IP address

is the local

host

ICMP, IEC,

Telnet, and

SNMP

packets

whose

destination

IP address

is the local

host

Telnet, SNMP,

and web

management

packets whose

destination IP

address is the

local host

ICMP,

IEC,

Telnet,

and

SNMP

packets

whose

destinatio

n IP

address is

the local

host

ICMP, IEC,

Telnet, and

SNMP packets

whose

destination IP

address is the

local host

ICMP, IEC,

Telnet, and

SNMP packets

whose

destination IP

address is the

local host

3-6

Document Module Feature WX5002 WX5002V2 LS8M1WCMA0 WX5004 LSWM1WCM10 LSWM1WCM20

Other protocol packets

supported

11MAC/802.

1X/ARP/DH

CP/HWTAC

AS/ICMP/IG

MP/MLD/L

WAPP/ND/

NTP/PIM/R

ADIUS

Data

packets: all

packets

except the

above

packets.

UDP/TCP/8

02.1X/DHC

P/IGMP/NT

P/ARP/LWA

PP/LooPbac

k/PPPoE/IA

CTP/ACSEI/

STP/LWAP

P_DATA/De

fault

11MAC/802.1X/

ARP/DHCP/HW

TACAS/ICMP/IG

MP/MLD/LWAP

P/ND/NTP/PIM

/RADIUS

Data packets: all

packets except

the above

packets.

UDP/TCP/

802.1X/D

HCP/IGM

P/NTP/AR

P/LWAPP

/LooPbac

k/PPPoE/I

ACTP/AC

SEI/

STP/LWA

PP_DATA

/Default

UDP/TCP/802.1

X/DHCP/IGMP/

NTP/ARP/LWA

PP/LooPback/P

PPoE/IACTP/A

CSEI/

STP/LWAPP_D

ATA/Default

UDP/TCP/802.1

X/DHCP/IGMP/

NTP/ARP/LWA

PP/LooPback/P

PPoE/IACTP/A

CSEI/

STP/LWAPP_D

ATA/Default

Enabling attack

prevention for

protocols

No Yes No Yes Yes Yes

Configuring rate limits

for a protocol

No Yes No Yes Yes Yes

Network

Management

and Monitoring

Configuration

Guide

Information center

configuration

Logfile No Yes No Yes Yes No

OAP module

configuration

No Yes No Yes No No

ACSEI server

configuration

No Yes No Yes No No

OAA

Configuration

Guide

OAA configuration

ACSEI client

configuration

No Yes Yes Yes Yes Yes

Access

Controller

Module Basic

Configuration

Guide

Access Controller

Module Basic

Configuration

Access Controller

Module Basic

Configuration

No No Yes No Yes Yes

3-7

Feature Matrix for the WX6000 Series

The switch interface module on the WX6103, and the LSQM1WCMB0, LSBM1WCM2A0, and LSRM1WCM2A1 access controller modules on the WX6000

series adopt the OAP architecture. Installed on the expansion slots of switches, they work as OAP cards to exchange data and status and control information

with the switches through their internal service interfaces. The XGE interfaces on the switch interface module on the WX6103, and the LSQM1WCMB0,

LSBM1WCM2A0, and LSWM1WCM10 access controller modules are internal interfaces. Do not configure services such as QoS rate limiting and 802.1X

authentication on them.

Table 3-2 Feature matrix for the WX6000 series

Volume Module Feature WX6103 LSQM1WCMB0 LSBM1WCM2A0 LSRM1WCM2A1

AUX user interface No No No Yes

Console user interface Yes Yes Yes Yes

Login configuration

Telnet Yes Yes

Yes (IPv6 telnet not

supported)

Yes

User interface

configuration

User interface type

AUX user interface

not supported

AUX user interface

not supported

AUX user interface

not supported

AUX user interface

not supported

File management

configuration

Configuration file

encryption

No No No No

Storage media supported CF and USB CF and USB CF and USB CF and USB

Fundamentals

Configuration Guide

Device management

configuration

License

128 APs at most by

default, and can be

extended to 640

APs.

128 APs at most by

default, and can be

extended to 640

APs.

128 APs at most by

default, and can be

extended to 640

APs.

128 APs at most by

default, and can be

extended to 640

APs.

WLAN Configuration WLAN services

Hot AC backup Yes Yes Yes Yes

3-8

Volume Module Feature WX6103 LSQM1WCMB0 LSBM1WCM2A0 LSRM1WCM2A1

Guide configuration

Maximum number of

SSIDs supported

512 512 512 512

Combo port configuration

The MPU does not

support the Combo

port.

No No No

Shutting down an

Ethernet interface

Yes Yes Yes Yes

Configuring flow control

on an Ethernet interface

Internal loopback

testing supported

on XGE interfaces

only

Internal loopback

testing supported

on XGE interfaces

only

Internal loopback

testing supported

on XGE interfaces

only

Internal loopback

testing supported

on XGE interfaces

only

Ethernet interface

configuration

Loopback detection on

an Ethernet interface

No No No No

Link aggregation

configuration

Link aggregation No No No No

MSTP Configuration STP No No No No

Layer 2 forwarding

configuration

Layer 2 forwarding No No No No

Layer 2 – LAN Switching

Configuration Guide

Port mirroring

configuration

Port mirroring No No No No

DNS configuration IPv6 DNS configuration Yes Yes No Yes

IP performance

optimization

configuration

Configuring ICMP to

send error packets

No No No No

Adjacency table

configuration

Displaying and

maintaining adjacency

table

Yes Yes Yes Yes

IPv6 basics

configuration

IPv6 basics configuration Yes Yes No Yes

Layer 3 – IP Services

Configuration Guide

IPv6 application

configuration

IPv6 application

configuration

Yes Yes No Yes

3-9

Volume Module Feature WX6103 LSQM1WCMB0 LSBM1WCM2A0 LSRM1WCM2A1

IP routing basics

configuration

IPv6-related displaying

and maintaining

commands

Yes Yes No Yes

Layer 3 – IP Routing

Configuration Guide

IPv6 static routing

configuration

IPv6 static routing

configuration

Yes Yes No Yes

MLD snooping

configuration

MLD snooping Yes Yes No No

IP Multicast

Configuration Guide

IPv6 multicast VLAN

configuration

IPv6 multicast VLAN Yes Yes No No

ACL configuration IPv6 ACL Yes Yes No Yes

Configuring line rate No No No No

ACL and QoS

Configuration Guide

QoS

Configuring CAR

applicable to all traffic of

online users

Yes Yes Yes Yes

AAA configuration

Specifying the device ID

to be used in stateful

failover mode

Yes Yes Yes Yes

Configuring Layer 3

portal authentication

Yes Yes Yes Yes

Specifying the portal

group to which the portal

service backup interface

belongs

Yes Yes Yes Yes

Specifying the device ID

to be used in stateful

failover mode

Yes Yes Yes Yes

Portal configuration

Specifying the backup

source IP address for

RADIUS packets to be

sent

Yes Yes Yes Yes

Security Configuration

Guide

SSH2.0 configuration

Specifying a source IPv6

address or interface for

an SSH client

Yes Yes No Yes

Page is loading ...

H3C LSQM1WCMB0 Configuration manual

H3C LSQM1WCMB0 Configuration manual

Related papers

Other documents