2. HPE
  3. About theNetworking Comware 5120v3 Switch Series

HPE About theNetworking Comware 5120v3 Switch Series User guide

  • Hello! I've analyzed the 'HPE Networking Comware 5120v3 Switch Series Command References' document. It provides comprehensive details on the commands for your Comware 5120v3 Switches. From basic setup and VLANs to advanced routing, security features and network monitoring, I'm ready to answer your questions about the switch's configuration and management.
  • What is covered in the 'Fundamentals Command Reference'?
    What are the main topics in the 'Layer 2—LAN Switching Command Reference'?
    What routing protocols are included in 'Layer 3—IP Routing Command Reference'?
    What security features are detailed in 'Security Command Reference'?
HPE Networking Comware
5120v3 Switch
Series
About the Command References
Software
version: Release 6352P02 and later
Document version: 6W100-20230715
© Copyright 2023 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the
United States and other countries.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.
About the command references
The HPE Networking Comware 5120v3 command references describe the commands and
command syntax options available for the HPE Networking Comware 5120v3 Switch Series.
Command reference
Content
Fundamentals Command
Reference
Covers the commands for logging in to and setting up the device.
This command reference includes:
• CLI (command privilege settings and CLI management commands).
• RBAC.
• Logging in to the switch.
• FTP and TFTP.
• File system management.
• Configuration file management.
• Software upgrade.
• Device management.
• Tcl.
• Python.
Virtual Technologies Command
Reference
Covers the commands for configuring the Intelligent Resilient Framework
(IRF) technology features. It covers planning the switch roles in the IRF
fabric, connecting the IRF links, and detecting and maintaining the IRF
fabric.
Layer 2—LAN Switching
Command Reference
Covers the commands for configuring Layer 2 technologies and features
in a LAN switched network.
This command reference includes:
• Ethernet interface.
• Loopback, null, and inloopback interfaces.
• Bulk interface configuration.
• MAC address table and MAC Information.
• Ethernet link aggregation.
• Port isolation.
• Spanning tree.
• Loop detection.
• VLAN (including VLAN, private VLAN, and voice VLAN).
• MVRP.
• QinQ.
• VLAN mapping.
• LLDP.
• L2PT.
• PPPoE relay.
Layer 3—IP Services
Command Reference
Covers the commands for configuring and managing IP addressing
(including static and dynamic IPv4 and IPv6 address assignment),
network performance optimization, and ARP.
This command reference includes:
• ARP (including gratuitous ARP, proxy ARP, ARP snooping, and ARP
direct route advertisement).
• IP addressing.
• DHCP.
• DNS.
• Basic IP forwarding.
Command reference
Content
• Fast forwarding.
• IP performance optimization.
• UDP helper.
• IPv6 basics.
• DHCPv6.
• IPv6 fast forwarding.
• HTTP redirect.
Layer 3—IP Routing Command
Reference
Covers the commands for configuring routes for IPv4 and IPv6 networks
of different sizes, route filtering, route control, and policy-based routing.
This command reference includes:
• Basic IP routing.
• Static routing.
• RIP.
• OSPF.
• Policy-based routing.
• IPv6 static routing.
• RIPng.
• OSPFv3.
• IPv6 policy-based routing.
• Routing policy.
IP Multicast Command
Reference
Covers the commands for Layer 2 IPv4 multicast protocols (including
IGMP snooping, PIM snooping, and multicast VLAN) and Layer 2 IPv6
multicast protocols (including MLD snooping, IPv6 PIM snooping, and
IPv6 multicast VLAN).
This command reference includes:
• IGMP snooping.
• PIM snooping.
• Multicast VLAN.
• MLD snooping.
• IPv6 PIM snooping.
• IPv6 multicast VLAN.
ACL and QoS Command
Reference
Covers the commands for classifying traffic with ACLs, and allocating
network resources and managing congestions with QoS technologies to
improve network performance and network use efficiency.
This command reference includes:
• ACL.
• QoS (including QoS policy, priority mapping, GTS and rate limit,
congestion management, and aggregate CAR).
• Data buffer.
• Time range.
Security Command Reference
Covers security feature commands. Available security features include
identity authentication (AAA), access security (802.1X, MAC
authentication, and port security), secure management (SSH), SSL, and
attack protection (IP source guard and ARP attack protection).
This command reference includes:
• AAA.
• 802.1X.
• MAC authentication.
• Portal.
• Web authentication.
• Port security.
Command reference
Content
• User profile.
• Password control.
• Public key management.
• PKI.
• IPsec (including IPsec, IKE, and IKEv2).
• SSH.
• SSL.
• Attack detection and prevention.
• TCP attack prevention.
• IP source guard.
• ARP attack protection.
• ND attack defense.
• SAVI.
• MFF.
• Crypto engine.
• FIPS.
• 802.1X client.
High Availability Command
Reference
Covers high availability commands for managing failure detection and
failover. Failure detection technologies focus on fault detection and
isolation. Failover technologies focus on network recovery.
This command reference includes:
• Ethernet OAM.
• CFD.
• DLDP.
• RRPP.
• ERPS.
• Smart Link.
• Monitor Link.
• VRRP.
• BFD.
• Track.
Network Management and
Monitoring Command
Reference
Covers the commands that help you manage and monitor your network,
for example, manage system events, collect traffic statistics, sample
packets, assess network performance, and test network connectivity.
This command reference includes:
• System maintenance and debugging (ping, tracert, and system
debugging).
• NQA.
• NTP and SNTP.
• PoE.
• SNMP.
• RMON.
• NETCONF.
• CWMP.
• EAA.
• Process monitoring and maintenance.
• Mirroring (including both port and traffic mirroring).
• sFlow.
• Information center.
Telemetry Command
Covers the commands for configuring gRPC.
Command reference
Content
Reference
OpenFlow Command
Reference Covers the commands for configuring OpenFlow.
/