BKM000936C

GODEER BKM000936C User manual

  • Hello! I am an AI chatbot trained to assist you with the GODEER BKM000936C User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
WF290589/WF290590
MADE IN VIETNAM PAGE 1 OF 10
ASSEMBLY INSTRUCTIONS
**PLACE ALL PARTS ON A CLEAN AND SMOOTH SURFACE SUCH AS A RUG OR CARPET TO
IMPORTANT NOTE
** BEFORE YOU BEGIN , KINDY FOLLOW THE ASSEMBLY INSTRUCTIONS STEP BY STEP
**DO NOT TIGHTEN ALL SCREWS AND BOLTS UNTIL THE BED IS FULLY SET-UP
AVOID THE PARTS FROM BEING SCRATCHED
MADE IN VIETNAM PAGE 2 OF 10
SAFETY WARNINGS AND GENERAL NOTES:
Follow the information on the warnings on the bunk bed end structure and on the carton. Do not
remove the warning label from the bed. Always use the recommended size mattress on mattress
support, or both, to help prevent the likelihood of entrapment or falls.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure the guardrail, ladder and other components are in their proper
position, free from damage, and all connectors are tight.
Always prohibit jumping on the bed.
Do not allow horseplay on or under beds.
Prohibit more than one person on upper bunk.
Always use the ladder for entering and leaving the upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Always use guardrails on both long sides of the upper bunk.
Use of a night light may provide added safely precaution for a child using the upper bunk.
If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD-Never attach or hang item to any part of the bunk bed that are not
designed for use with the bed.
Keep these instructions for future reference.
We recommend assembling your bunk bed on the shipping carton to protect your floor or carpet .
Be certain all staples are out of the box before beginning assembly on the shipping carton.
USE ONLY MATTRESSES WHICH ARE AS THE TABLE BELOW ON UPPER AND ON LOWER BUNKS.
Upper bunk
Bed type Length Width Thickness
Twin Standard 74" - 75" 6" max
Lower bunk
Bed type Length Width Thickness
Twin Standard 74" - 75" 381/2 " 8" max
SURFACE OF MATTRESS MUST BE AT LEAST 5" (127MM) BELOW THE UPPER EDGE OF
GUARDRAILS.
Replacement parts:
Replacement parts, including additional guardrails, may be obtained from any of our
(GIGACLOUD TECHNOLOGY (USA) INC.) LINK USA CO.,LTD LAND PARCEL 188,MAP NO.38,
TAN LOI HAMLET,DATCUOC COMMUNE,BAC TAN UYEN DISTRICT,BINH DUONG VIET NAM dealers
(bunk bed and tribed included)
381/2 "
MADE IN VIETNAM PAGE 3 OF 10
1
ASSEMBLY INSTRUCTIONS
Lower Bed Panel (2 pcs)
PART LIST BOX 1: WF 290589
2
WF290589/WF290590
Lower Bed Panel (2 pcs)
35
4
6
7 8
Roll Slat (26 pcs)
Stand in Pull Box (4pcs)
Left Wheel Board (2pcs) Right Wheel Board (2 pcs)
35
4
6
7 8
Leg (4 pcs)
Side Pull Box (4pcs) Back Panel Pull Box (2 pcs)
Pull Box Bottom Board (2pcs)
9
11
10
Pull Box Bottom Board (2 pcs)
PART LIST BOX 2: WF 290590
Left Lower Rail (1 pc)
Left Bed Post (2pcs)
Right Lower Rail (1pc)
Right Upper Rail (1 pc)
12 1413
Left Upper Rail (1 pc)
Right Bed Post (2pcs)
Left Stair (1 pc) Right Stair (4pcs) Stairs (4 pcs)
15 1716
18 2019
(Ø 5/16 "X25mm)
( m4x38mm-RBW)
Short Bolt (16 pcs)
Flat Head Screw (24 pcs)
(Ø 5/16 "X38mm)
Long Bolt (28 pcs)
( Ø 5/16 "-RBW )
Flat Washer (44 pcs)
(M4x75mm x32mm)
( Ø 5/16 "-RBW )
Spring Washer (44 pcs)
Allen Wrench (1 pc)
( m4x20mm-RBW)
Flat Head Screw (32 pcs)
Wheels (8 pcs)
( m59x42mmx66mm)
MADE IN VIETNAM PAGE 4 OF 10
ASSEMBLY INSTRUCTIONS
WF290589/WF290590
A C
HARDWARE LIST IN WF290590
B
D FE
GHI
( m4x30mm-RBW)
Flat Head Screw (60 pcs)
J
Wood dowel (8PCS)
MADE IN VIETNAM PAGE 5 OF 10
STEP 2
STEP 1
ASSEMBLY INSTRUCTIONS
(Ø 5/16 "X38mm)
Bolt
A16pcs
( Ø 5/16 "-RBW )
Flat Washer
B
16pcs
16pcs
( Ø 5/16 "-RBW )
Spring Washer
D
1pc
(M5x75mm x32mm)
Allen Wrench
E
16 17
4
D
A
B
1
2
16
17 16
1
2
17
E
A4pcs
Leg
x2
MADE IN VIETNAM PAGE 6 OF 10
STEP 4
STEP 3
ASSEMBLY INSTRUCTIONS
G
( m4x30mm-RBW)
Flat Head Screw
26pcs
(Ø 5/16 "X25mm)
Bolt
C 8pcs
( Ø 5/16 "-RBW )
Flat Washer
B
8pcs
8pcs
( Ø 5/16 "-RBW )
Spring Washer
D
1pc
(M5x75mm x32mm)
Allen Wrench
E
12
2
2
16
17
17
D
C
E
B
D
C
E
B
16
13
1
1
G
E
3
3
12
13
3
3 3/8 ''
NOTEDo not lock the screws of the trundle slats to the utermost edge
the trundle slats,you need to leave a certain space at the edges, otherwise
it will cause the board to break.
ASSEMBLY INSTRUCTIONS
MADE IN VIETNAM PAGE 7 OF 10
STEP 6
STEP 5
G
12
13
14
15
D
C
E
B
D
C
E
B
(Ø 5/16 "X25mm)
Bolt
C 8pcs
( Ø 5/16 "-RBW )
Flat Washer
B
8pcs
8pcs
( Ø 5/16 "-RBW )
Spring Washer
D
1pc
(M5x75mm x32mm)
Allen Wrench
E
3
3
2
2
G
( m4x30mm-RBW)
Flat Head Screw
26pcs
3 3/8 ''
NOTEDo not lock the screws of the trundle slats to the utermost edge
the trundle slats,you need to leave a certain space at the edges, otherwise
it will cause the board to break.
ASSEMBLY INSTRUCTIONS
MADE IN VIETNAM PAGE 8 OF 10
STEP 7 B
A
D
E
E
D
A
B
E
DB
A
20
19
18
18
19
20
STEP 8
D
A
E
B
( Ø 5/16 "-RBW )
Flat Washer
8pcs
8pcs
( Ø 5/16 "-RBW )
Spring Washer
D
E
(Ø 5/16 "X38mm)
Bolt
A4pcs
( Ø 5/16 "-RBW )
Flat Washer
B
4pcs
4pcs
( Ø 5/16 "-RBW )
Spring Washer
D
1pc
(M5x75mm x32mm)
Allen Wrench
E
15
13
18
19
20
J20
8pcs
J
Wood dowel
(Ø 5/16 "X38mm)
Bolt
A8pcs
B(M5x75mm x32mm)
Allen Wrench
1pc
ASSEMBLY INSTRUCTIONS
MADE IN VIETNAM PAGE 9 OF 10
STEP 9
STEP 10
H
( m4x38mm-RBW)
Flat Head Screw
8pcs
H
( m4x38mm-RBW)
Flat Head Screw
8pcs
G
( m4x30mm-RBW)
Flat Head Screw
8pcs
G
STEP 11
8
7
8
7
8
8
10
9
8
11
9
8
8
8
9
11
8
7
H
H
H
H
80MM
ASSEMBLY INSTRUCTIONS
MADE IN VIETNAM PAGE 10 OF 10
STEP 12
COMPLETE
STEP 14
STEP 13
H
( m4x38mm-RBW)
Flat Head Screw
8pcs
I
F
I
( m4x20mm-RBW)
Flat Head Screw
32pcs
H
9
5
6
11
8
H
5
11
8
6
8
11
F
9
88
9
/