2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Innovative
  6. 18690
18690

Innovative 18690 User manual

  • Hello! I've reviewed the installation instructions for the HAT Collective Monitor mount STX-2-XXX-SLD-YYY. This document provides detailed guidance on how to assemble and install the mount, including both desk clamp and thru-desk options. It also covers features like adjustable arms, rotation stops, and cable management. I am ready to answer your questions about the setup and features of this mount.
  • What is the maximum desk thickness for the clamp mount?
    What tool is required to tighten the adjustment screw?
    Is a thru-desk kit included?
STA X X
Installation Instructions
™
© 2021 Innovative Ergonomic Solutions REV A
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
STX-2-XXX-SLD-YYY
PAGE 1 OF 15
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
PARTS LIST
A Top Down Mount 1x
8524
B Dimpled Pole 1x
110607-20
C Stackable Mount 2x
413054
D Pole Collar 1x
113332
E Pole Clip 1x
113449
F Dog Washer for Articulating Arms 2x
113704
G Rotation Stop for Articulating Arms 2x
113705
H M6 x 1mm Phillips Pan Head Screw 2x
105304
I Quick Connect VESA Plate 2x
114808
J M4 x 12mm Phillips Pan Head Screw 8x
701153
K 9-inch Beam Assembly 2x
416088
L Dog Washer 2x
105189
M 10-32 x 3/8" FPhMS w/Lock Patch 2x
705198
N Pole Cap 1x
105195
O Cable Clip 1x
104533
P Cable Cap 2x
114810
Q Forearm Cable Cap 2x
115584
R 1/8" Allen Wrench 1x
701312
S 3/32" Allen Wrench 1x
700146
T 7/32" Allen Wrench 1x
701127
U 4mm Allen Wrench 1x
709877
V* M8 x 95mm SCHS 1x
716061
W* Spacer 1x
701544
X* Lock Nut 1x
710015
PAGE 2 OF 15
T
A
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
OR
PAGE 3 OF 15
3 4
THRU-DESK CONFIGURATION*
T
V
W
X
7/32"
Desk thickness
up to 1.5" (3.8 cm)
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
PAGE 4 OF 15
i
IMP OR TAN T:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
5
B
C
D
S
3/32"
PAGE 5 OF 15
6
E
PAGE 6 OF 15
F
G
7
H
F
iIMP OR TAN T:
Install part (G) in the
orientation as shown to
the left. When washer,
part (G), is installed
correctly, the arms will
not rotate past the back
of the mount.
PAGE 7 OF 15
2x
I
K
L
M
8
PAGE 8 OF 15
2x
K
O
M
9
L
PAGE 9 OF 15
10
J
I
PAGE 10 OF 15
11
2x
PAGE 11 OF 15
12
T
7/32"
i
In some instances, an additional
counterbalance adjustment may
be needed to allow the arm’s
instant height adjustment function
to work properly.
If your arm is not staying in position
after performing step 12, tighten
the adjustment screw with a
1/8" Allen wrench.
R
1/8"
Optional Adjustment
2x
PAGE 12 OF 15
13
4 mm
U
2x
PAGE 13 OF 15
14
2x
PAGE 14 OF 15
N
15
P
O
2x
PAGE 15 OF 15
/