Premier Mounts WMK-027 User manual

Brand: Premier Mounts

Model: WMK-027

Category: Projector mounts

Type: User manual

Premier Mounts WMK-027 is a universal short throw wall mount designed for projectors weighing up to 75 lbs. It features a storage enclosure for electronic components, adjustable height and tilt, and extension arm compatibility for flexible positioning. Installation is simplified with the included hardware and templates. The WMK-027 is ideal for classrooms, conference rooms, and home theaters, providing a secure and versatile mounting solution for your projector.

WMK-027

Universal Short Throw Wall Mount

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada –

Phone: 800-368-9700

Fax: 800-832-4888

EUROPE

Swallow House,

Shilton Industrial Estate,

Shilton, Coventry, England CV79JY

Phone: +44 (0) 2476 614700

Fax: +44 (0) 2476 614710

Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044

©Premier Mounts 2009

9530-070-353-00

INSTALLATION INSTRUCTIONS

ViewSonic by Premier Mounts

Page 2 Installation Instructions

Table of Contents

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT

FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACH-

MENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR

CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY

SUCH USE, ATTACHMENTS OR MODIFICATIONS.

THE SURFACE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE PROJECTOR. IF NOT,

THE STRUCTURE MUST BE REINFORCED. THE MAXIMUM WEIGHT THAT CAN BE USED WITH THIS PRODUCT IS 75LBS.

PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE INSTALLATION

INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN

DEATH.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER

SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the

projector.

If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is

recommended.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires

in wall. Cutting/drilling into an electrical line may cause serious injury.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact

Contact Premier Mounts with any questions

(800) 368-9700

[email protected]

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COM-

PLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND

PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE

REFERENCE.

Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water

damage to the mounting surface.

Warning Statements

Warning Statements 2

Parts List 3

Installation Tools 3

Determining the Installation Height 4

Wood Stud Installation 5

Solid Surface Installation 6

Utilizing the Storage Feature 7

Attaching the Projector Arm 7

Throw Distance Calculation 8

Upper Mounting Bracket Installation 9

Extension Arm Installation 10

Base Box Installation 10

Cable Management 11

Set Screw Installation (Optional) 11

Technical Specications 12

Warranty 13

WMK-027

Installation Instructions Page 3

Parts List

This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are

missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the

installation and contact Premier Mounts (800) 368-9700.

Wall Plate (Qty 1)

Arm Assembly (Qty 1)

Upper Mounting Bracket

(Qty 1)

End Cover (Qty 1)

M5 x 12mm Security Head

Screws (Qty 11)

Inner Slide Plate (Qty 1)

3/8” Concrete Wedge

Anchors (Qty 4)

5/16 x 3” Lag

Bolts (Qty 4)

5/16 Flat

Washers (Qty 4)

Installation Tools (not supplied)

Phillips Screwdriver

1/4” Drill Bit

Electronic Stud Finder

Drill

Level

1/2” Socket and Socket

Wrench

Extension Arm - Optional (Qty 1)

included with the WMK-027

Back Plate

Covers (Qty 2)

WMK-027

Security Wrenches

(PDS-PLUS Hardware Pack)

3/8” Masonry Drill Bit

M6 x 12mm Security

Head Screws (Qty 4)

Extension Hardware Pack

M6 x 12mm Security (Qty 2)

1/4” Flat Washer (Qty 2)

1/4” Nylon Spacer

(Qty 2)

M6 Set Screws

Security (Qty 1)

Non-Security (Qty 1)

PDS-PLUS Projector

Mount

Page 4 Installation Instructions

Determining the Installation Height

Step 1. Measure distance from center of lens to the top of the PDS-PLUS bracket.

Step 2. Add the distance from the ground to the top of the screen (A), the recommended offset from the projector manual (B),

the measurement from Step 1 (C), and then add 1.5”.

(Example: A + B + C + 1.5” = ?)

Step 3. Measure the calculated distance from the top edge of the viewable area of the screen/whiteboard and mark the wall. This mark

will represent the lower edge of the wall plate.

Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the screen/whiteboard.

Lens

PDS-PLUS Bracket

Projector

In order to determine the installation height and throw distance, the PDS-PLUS projector bracket must be mounted to the

projector. Please refer to the PDS-PLUS Installation Instructions prior to performing the following steps.

Top of Screen

Mark

Legend

A - Distance from ground to the top of the

screen/whiteboard (viewable area).

B - Manufacturers recommended offset

measurement. This measurement will be

listed in the Users Manual.

C - Center of the lens to the top of the

PDS-PLUS bracket.

Add 1.5” to the calculated total. This total distance

will be the location for the bottom rail on the wall

plate.

Ground

WMK-027

Installation Instructions Page 5

Wood Stud Installation

DEAD CENTER MUST BE LOCATED ON THE STUD FOR CORRECT AND SAFE INSTALLATION.

Step 1. Use an electronic stud nder

(commercially available) to

locate the center of the stud

that is in the wall.

Step 2. Use a pencil to mark the rst

mounting hole, just above

your height mark (from

page 4).

Step 3. Use the level to make sure

the wall plate is level from

top to bottom. After

determining the desired

viewing height, place the

wall plate over the rst hole

and use a pencil to mark the

rest of the holes.

Wood Stud

Stud nder

Marking

(from page 4)

Wood Stud

Marking

Wall

Plate

Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury

or damage to property.

WMK-027

Step 4. Once the holes have been

marked, use a 1/4” drill bit

and portable drill to drill the

pilot holes.

Step 5. After the pilot holes have

been drilled, use four (4)

5/16” x 3” lag bolts and four

(4) at washers to mount the

wall plate to the wooden

stud. Use a 1/2” socket and

socket wrench to nish this

step.

Step 6. Insert and gently tap the wall

plate covers into place.

Drill

Marking

Socket

Lag Bolt and

Flat Washer

Wall

Plate

Completed Installation

Wall Plate

Covers

Page 6 Installation Instructions

Solid Surface Installation

Concrete drill bits are commercially available.

Step 1. Place the wall plate against

the wall and use a level to

make sure the wall plate is

level from top to bottom.

Step 2. Use a pencil to mark the

location of the mounting

holes.

Step 3. Use a 3/8” drill bit to drill the

mounting holes where the

marks were made with a

pencil.

Step 4. Once the holes have been

drilled, place the concrete

wedge anchors into the

hole. Using a hammer,

gently tap into place.

Step 5. Once the wedge anchors

have been inserted into the

mounting holes, remove the

nut and at washer from the

wedge anchor.

Marking

Drill

Pilot Hole

Hammer

Wedge Anchor

3/8” Drill Bit

Step 6. Place the wall plate over the

wedge anchors once the

wedge anchors have been

correctly inserted into the

mounting surface.

Step 7. Place the at washer and

nut onto the wedge anchor

and tighten using a socket

and socket wrench. Do not

overtighten.

Step 8. Insert and gently tap the wall

plate covers into place.

Completed Installation

Seated Wedge

Anchor

Wall Plate

Socket

Wall Plate

Nut and Washer

Wall Plate

Covers

WMK-027

Installation Instructions Page 7

WMK-027

Utilizing the Storage Feature

The storage feature may be used to store electronic components. There is an accessible door on each side of the storage enclosure. It may

be securely held shut with the use of four (4) M5 x 12mm security head screws. It may be easiest to pre-wire all cables down the arm (or

extension) at this time (see Page 11).

Electronic

Components

Electronic

Components

Door

Security

Wrench

M5 x 12mm

Security Screw

Step 1. Open the storage door that is located on the side of

the wall plate.

Step 2. Place the electronic components inside the storage

enclosure.

Step 3. Make all electronic connections at this time.

Step 4. Close the storage door and secure using two

(2; 1 upper and 1 lower) M5 x 12mm security

head screws. Tighten using a security wrench.

Repeat this process for the other side as well.

Attaching the Projector Arm

Step 1. Locate the mounting hook cutout on the top of the wall plate.

Step 2. Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts.

Step 3. Slowly lower and let the projector arm rest against the wall plate.

Mounting Hook Cutout

Mounting Hooks

Wall Plate

Projector Arm

Page 8 Installation Instructions

Please review the Operator’s Manual that came packaged with your projector before attaching the upper mounting

bracket. The correct throw distance (the distance from the projector to the screen) must be determined prior to mounting

the projector.

Throw Distance Calculation

Step 1. Refer to the projectors Users Manual to

determine the distance from the lens to the

front of the screen.

Step 2. Measure the distance from the front of the

lens to the center of the PDS-PLUS (see

diagram).

Front Mounted Lens

For front-mounted lenses, add distance (Y)

to distance listed in projector Users Manual.

Rear Mounted Lens

For rear-mounted lenses, subtract disance (Y) from

the distance listed.

Step 4. Use a tape measure to mark the appropriate

distance on the WMK-027. This

will be where the center of the mounting

bracket will be located.

WMK-027

MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT.

Step 4. Locate the two (2) lock mounting points on the projector arm. These two points will be aligned with the lock mounting

points on the wall plate.

Step 5. Using a security wrench, insert and tighten two (2) M5 x 12mm security head screws.

DO NOT OVERTIGHTEN THE SCREWS.

Lock Mounting Point

M5 x 12mm Security Head Screw

Screwdriver/Security Wrench

If installing WMK-027, please refer

to Page 10 before continuing.

Front Lens

Rear Lens

Calculations

X = Manufacturers recommended

throw distance

Z = Distance from wall to face of

whiteboard/screen

Front Lens Throw Distance =

(X + Y + Z)

Rear Lens Throw Distance =

(X - Y + Z)

Installation Instructions Page 9

Security

Wrench

WMK-027

Step 1. Insert the inner slide plate into the projector

arm.

Step 2. Determine which adjustment slot will be

best for the projector placement.

Step 3. Raise the upper mounting bracket into

position.

Step 4. Align the mounting holes of the upper

projector plate with the mounting holes of

the inner slide plate.

Step 5. Secure and nger-tighten two (2)

M6 x 12mm security head screws.

Step 6. Once the correct throw distance has been

determined, use the security wrench

(supplied) to tighten the mounting screws.

Do not overtighten the screws.

Projector Arm

Inner Slide

Plate

Upper Mounting

Bracket

M6 x 12mm

Security Screw

Adjustment

Slot

Calculated

Throw Distance

Upper Mounting Bracket Installation

Page 10 Installation Instructions

WMK-027

Base Box Installation

Base Box

M6 x 12mm Screws

Step 1. Raise the base box projector mount to the upper mounting bracket.

Step 2. Align the two (2; one each side) mounting holes.

Step 3. Using a screwdriver/security wrench, insert and tighten two (2) M6 x 12mm security head screws. Do not over tighten the

screws.

Step 4. Attach the projector to the base box, referring to the PDS-PLUS Installation Instructions for nal adjustments.

Please review the Operator’s Manual that

came packaged with the PDS-PLUS before

attaching the PDS-PLUS to the upper mounting

bracket.

Security Wrench

Projector Mount

Extension Arm Installation (Optional)

Step 1. Slide the extension arm into the open end of the WMK-027 (the front of the mount).

Step 2. Attach the upper mounting bracket directly to the extension using two (2) M6 x 12mm set screws (see page 8).

Step 3. Adjust length so that the center of the upper mounting bracket matches the throw distance calibration.

Step 4. Line up the mounting holes on the extension arm with the mounting slots on the WMK-027.

Step 5. Using a screwdriver, insert and tighten two (2) M6 x 12mm security head screws, 1/4” at washers and 1/4” nylon spacers.

Step 6. Attach the PDS-PLUS (see page 10).

M6 x 12

Security Screw

Security

Wrench

1/4” Flat

Washers

Upper

Mounting

Bracket

WMK-027

If the extension arm was purchased at a later date, the end cover must be removed prior to installing the extension arm.

Please see the Operator’s Manual to determine the correct throw distance (the distance from the projector to the screen)

must be determined prior to mounting the projector.

1/4” Nylon

Spacer

Extension Arm

Installation Instructions Page 11

Cable Management

WMK-027

Electronic Components

Electronic

Components

Cables

WMK-027

Cable Opening

Projector Hook-Ups

Electronic Components

Cable Opening

Step 1. The cable access holes are located at the end of the short throw mount and on the wall plate.

Step 2. Route the cables through one end of the WMK-027 and out the other end.

Set Screw Installation (Optional)

The M6 set screw will be used in conjunction with any

standard 1-1/2” NPT or CLS (sold separately).

Step 1. Thread in CLS or any 1-1/2” NPT until

securely fastened.

Step 2. Thread in one (1) M6 x 6mm set screw.

Step 3. Use an M3 security wrench to tighten the M6

set screw (included in the PDS-PLUS

hardware).

Upper Mounting

Bracket

M6 Set Screw

M3 Security

Wrench

WMK-027

Page 12 Installation Instructions

Technical Specications

All measurements are in inches(mm).

Warranty

PREMIER MOUNTS

LIMITED LIFETIME WARRANTY

What and Who is Covered by this Limited Warranty and for How Long

Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of

the original owner of this product. The limited warranty is valid only for the original purchaser of the product.

What Premier Mounts Will Do

At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is

defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will

be shipped to you at no charge, but you must pay any labor costs.

What is Not Covered; Limitations

PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-

PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN

PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.

PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER

MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-

ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-

ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE

LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

What Customers Must Do for Limited Warranty Service

If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to

the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-

sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the

problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier

Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.

Premier Mounts

Attn: Warranty Claim

3130 East Miraloma Ave.

Anaheim, CA 92806

How State Law Applies

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER

RIGHTS WHICH VARY FROM STATE TO STATE.

Installation Instructions Page 13

WMK-027

Premier Mounts WMK-027 User manual

Brand: Premier Mounts

Model: WMK-027

Category: Projector mounts

Type: User manual

Download PDF

report

Premier Mounts WMK-027 User manual

Premier Mounts WMK-027 User manual

Related papers

Other documents