Vitek VTC-BHOC6R4F User manual

Brand: Vitek

Model: VTC-BHOC6R4F

Category: Security cameras

Type: User manual

Vitek VTC-BHOC6R4F is an advanced vandal resistant bullet camera designed for outdoor surveillance with features like 2.1 MegaPixel Progressive Scan CMOS sensor, 30 IR LEDs with 115’ range, mechanical IR cut filter, advanced OSD functions, 100% pure digital transmission of video data, IP67 weather resistance, and more.

External OSD

Controls

for Ease of

installation

VITEK

FEATURES:

• 1/3” 2.1 MegaPixel Progressive Scan CMOS sensor w/

NVP2420 DSP

• 2.1 MegaPixel With full 1080p 3G-SDI (SMPTE 424M) @

60fps / 30fps HD-SDI (SMPTE 292M) @ 30fps Output

• 30 850nm Dynamic Intensity IR LEDs with 115’ Range

• MegaPixel IR Corrected 3.6mm Fixed Iris lens Included

• Mechanical IR Cut Filter (True Day/Night)

• XD-DNR (2D-DNR + 3D-DNR) Noise Reduction

• 16:9 Video format

• Advanced OSD Functions: Defog, Dynamic IR, WDR,

Motion Detection, Privacy mask, Mirror, BLC/HLC, D-Zoom

• 100% Pure Digital Transmission of video data

• Up to 700’ HD Transmission Range (Depending on cable

characteristics and integrity)

• IP67 Weather Resistance

• 12VDC Operation

VTC-BHOC6R4F

2.1MP 3G-SDI IP67 Vandal Resistant WDR True

Day/Night Bullet Camera with 3.6mm Lens &

30 IR LEDs

WARNINGS

The camera needs periodic inspection.

• Contact an authorized technician for inspection.

Stop using camera if there is a malfunction.

• Avoid installing camera in high heat areas, risk of fire may occur.

Do not install the camera on a surface that can not support it.

• Unless the surface is suitable, injury or other hazards may occur.

Do not disassemble the camera.

• It may result in fire, electric shock or other hazards.

Do not hold plug with wet hands.

• It could cause an electric shock.

Do not use the camera close to a gas or oil leak.

• It may result in fire or hazards.

PRECAUTIONS

Ø Do not install the camera in extreme temperature conditions.

• Only use the camera under conditions where temperatures are

between -14˚F and +122˚F. Be especially careful to provide ventilation

when operating under high temperatures.

Ø Do not drop the camera or subject it to physical shocks.

• It may cause malfunctions to occur.

Ø Never point camera into a strong light source, such as the

sun or bright spotlight.

• It can damage the CMOS Sensor.

Ø Do not expose the camera to radioactivity.

• This will damage the CMOS sensor.

NOTE

• If the camera is exposed to spotlight or object reflecting strong

light, smear or blooming may occur.

• Please check power specs before connecting power.

• 1/3” 2.0 Mega-Pixel Panasonic Progressive Scan Sensor

• Resolution: 1920 x 1080 (30P/25P, 60P/50P, 60i/50i)

• HD-SDI / SMPTE 292M (30P/25P HD-SDI), SMPTE 424M

(60P/50P 3G SDI) Video Output

• HD over Coaxial Cable

• Uncompressed HD Digital Video

• WDR

• True Day/Night by ICR

• Smart 3DNR, 2DNR / Smart IR

• RS-485 (Pelco®-D) Remote Control, Coaxial Cable Comm.

• Sens-UP: 2x ~ 30x

• Motion Detect, Mirror, Privacy Mask, De-fog, BLC/HLC, D-Zoom

FEATURES

Setup Menu (OSD)

[How to operate OSD joy stick]

OSD menu is controlled by OSD joystick in OSD Board or OSD Cable

-▲ (UP), ▼ (DOWN), ◀ (LEFT), ▶ (RIGHT), ● (SET / ENTER)

[Menu Tree]

SETUP MENU (OSD)

[Menu Tree]

MENU TREE

[Menu Tree]

MENU TREE

[Menu Tree]

MENU TREE

Main OSD Menu

MAIN MENU

DEFAULT

DESCRIPTION

LENS

Select Lens type according to mounted or built-in lens

EXPOSURE

Set SHUTTER, AGC, SENS-UP, BRIGHTNESS,

D-WDR &, DEFOG

BACK LIGHT

Select WDR, BLC, HSBLC or OFF

WHITE BAL ATW

* ATW(Auto Tracking White Balance) * AWC ->

SET : White Balance is fixed at the value when

*(enter) is pressed and keeps the value

* INDOOR : White Balance is fixed at about 3100K

* OUTDOOR : White Balance is fixed at about 5100K

* Manual : Adjustable value of BLUE and RED

DAY&NIGHT AUTO

* AUTO: DAY or NIGHT is set automatically by light

level coming in through lens. DELAY TIME, D -> N

and N -> D, can be set in the menu

* COLOR : Color video output * B/W : B/W video

output regardless of light level

(removes IR cut filter automatically)

* EXT : Day(Color) or Night(B/W) is decided by

external light sensor(CDS sensor)

All IR LED cameras should be set to EXT.

* Set 2DNR, 3DNR, LEVEL, SMART NR

SPECIAL

* Set CAM TITLE, D-EFFECT, MOTION, PRIVACY,

LANGUAGE,DEFECT & RS 485

ADJUST

* Set SHARPNESS, MONITOR, LSC, TV SYSTEM

(Video Out), RESOLUTION & FRAME RATE

RESET

* Push • (Enter) at FACTORY, all parameters return

to factory default.

EXIT

* Save all and Exit

MAIN OSD MENU

1. LENS

Select Lens type, DC, MANUAL or P-IRIS.

DC Lens: * MODE: Set INDOOR or OUTDOOR

2. EXPOSURE

EXPOSURE

DEFAULT

DESCRIPTION

SHUTTER AUTO

Set Shutter Speed, 1/60(1/50), FLK, 1/240 ~

1/50000 or x2 ~ x30

* If camera is equipped with auto iris lens,

recommended to set to AUTO.

* In the region NTSC but 50Hz power, set to FLK

(Flickerless). In the FLK mode, sensitivity will be

lowered under low light.

* X2 ~ x30, SENS-UP is working at selected

frame integration rate regardless of light level.

AGC

* Under lowest light level, AGC is maximized by

Automatic Gain Controller * Can set AGC level

SENS-UP AUTO

* If set to AUTO, Set limitation of maximum

integration frame rate 2 ~ x30

* Higher SENS-UP rate is higher sensitivity but

slower refresh rate.

* Due to long shutter time, some white dots may

appear.

* Usable at AUTO or 1/60(1/50) for A60/50P,

A60/50i & A30/25P and 1/30(1/25) for B30/25P

set up

BRIGHTNESS 40

* Brightness level. The higher the value, the

brighter the image is.

* Brightness is controlled by the iris of auto iris

lens or shutter speed of fixed iris lens.

D-WDR OFF

* D-WDR is to enhance brightness of dark areas

by partially increasing gain.

* If set too high, white noise will increased in the

2. EXPOSURE

1. LENS

dark area.

DEFOG OFF

* This is to enhance visibility in foggy

environments but the performance is limited.

3. BACKLIGHT

Select Backlight mode, WDR, BLC or HSBLC

3-1. WDR

Set WDR level, LOW, MIDDLE or HIGH

Note) WDR mode works only with HD-SDI output and not the CVBS

(composite out)

3-2. BLC

* BLC: This function is used to brighten an image in the foreground with a

highly bright area behind it such as sunlight, limiting the affect of a

silhouette

BLC

DEFAULT

DESCRIPTION

GAIN MIDDLE

* Gain will compensate the brightness of objects

in the selected area.

* Higher GAIN can brighten the object but other

areas may saturate and noise may increase.

* BLC may not work correctly if the background is

dark and bright.

AREA

* This is to set the size and location of BLC area.

* If the area is too small the compensation may

be unstable, and if too large it will be less

effective

* Area has 15 x 8 blocks and the SIZE and

POSITION can be set by UP/DOWN/LEFT/

RIGHT button.

DEFAULT AUTO

* Reset current settings and loads the default for

BLC setting.

3. BACKLIGHT

3-3. HSBLC

This function is used to black out highlighted (bright) areas, in order to enable a clear

visual image of objects, such as the license plates of an oncoming vehicle or other

objects that may be obstructed by headlamps.

HSBLC

DEFAULT

DESCRIPTION

SELECT

AREA1

* Select area to adjust AREA 1~4.

DISPLAY ON

* Choose ON then push ● button to enter into

selected area.

Can set POSITION & SIZE of the area

LEVEL 45

Defines the threshold level for HLC. Lower value

is more sensitive.

MODE ALL DAY

* Choose ALL DAY or NIGHT

* ALL DAY : HSBLC works all day regardless of

DAY or NIGHT mode

* NIGHT : HSBLC works when camera is in

NIGHT mode only

BLACK MASK

* Set ON or OFF for displaying black mask.

DEFAULT

* Reset current settings and loads default of

HSBLC.

BLC ON

BLC OFF

4. WHITE BAL

WHITE BAL

DEFAULT

DESCRIPTION

WHITE BAL ATW

* ATW

(Auto Tracking White balance)

White balance performs automatically

* AWC -> SET :

Sets the white balance to the

current scene

* INDOOR : White balance is fixed at about

3100K

* OUTDOOR : White balance is fixed at

about 5100K

* MANUAL : Adjustable fixed value of RED &

BLUE

* AWB : Auto White Balance

4. WHITE BALANCE

HSBLC ON

HSBLC OFF

5. DAY & NIGHT

DAY & NIGHT

DEFAULT

DESCRIPTION

DAY & NIGHT AUTO

* AUTO : Camera switches DAY from/to NIGHT

automatically according to the amount of light

through the lens.

* COLOR : Camera stays color regardless of light

level

* B/W: Camera stays black & white regardless of

light level.

* EXT : DAY or NIGHT is decided by light

sensor(CDS sensor) use this if camera has

built in IR’s

5-1. AUTO

AUTO

DEFAULT

DESCRIPTION

DELAY 5

* DELAY is dwell time before switching D->N or

N->D after checking light level.

*DELAY can avoid unnecessary switching by

short term light.

* Camera should retain the present environment

for longer than DELAY (DWELL TIME).

D -> N (AGC) 80

* D->N is threshold level to switch from DAY to

NIGHT.

* Lower value makes the camera switch to NIGHT

mode at lower light level.

N -> D (AGC) 35

* N->D is threshold level to switch from NIGHT to

DAY.

* Lower value makes the camera exit NIGHT

mode at brighter light level

* If the gap between D -> N and N -> D value is too small, repeated

switching may occur

Recommend set the gap to more than 40

5. DAY & NIGHT

5-2. B/W

B/W

DEFAULT

DESCRIPTION

BURST

* Set BURST ON or OFF

IR SMART

OFF

* Set IR SMART ON or OFF

5-3. EXT

EXT

DEFAULT

DESCRIPTION

BURST

* Set BURST ON or OFF

IR SMART

OFF

* Set IR SMART ON or OFF

6. NR

2D & 3D is a powerful noise reduction technology at low light.

2DNR reduces noise with spatial frequency for each field but too strong of noise reduction will

be loss of sharpness. 3 DNR (3-dimensional noise reduction)

which reduces the noise by multi frame comparison? Noise Reduction is

effective at low light. Setting a higher level of noise reduction may result in the loss of

sharpness and the tail effect of a comet may occur.

6. NR

5-2. B/W

B/W

DEFAULT

DESCRIPTION

BURST

* Set BURST ON or OFF

IR SMART

OFF

* Set IR SMART ON or OFF

5-3. EXT

EXT

DEFAULT

DESCRIPTION

BURST

* Set BURST ON or OFF

IR SMART

OFF

* Set IR SMART ON or OFF

6. NR

2D & 3D is a powerful noise reduction technology at low light.

2DNR reduces noise with spatial frequency for each field but too strong of noise

reduction will be loss of sharpness. 3 DNR (3-dimensional noise reduction)

which reduces the noise by multi frame comparison? Noise Reduction is

effective at low light. Setting a higher level of noise reduction may result in the loss of

sharpness and the tail effect of a comet may occur.

6-1. 3DNR (ON)

3DNR

DEFAULT

DESCRIPTION

SMART NR ON

* Camera is watching for any motions.

* When no motion is detect: 3 DNR is working

with maximum noise reduction

automatically. This will save

HDD space on the DVR

* When motion is detected: 3 DNR deactivates

slow motion capture for

moving object.

LEVEL 80

* Set strength of 2D & 3 DNR.

* Higher value, higher noise reduction.

* If set too high, sharpness will be lost in 2 DNR

and will have a tail effect in 3 DNR

START. AGC 0

* Set Start level of noise reduction

* Higher level allows 3 DNR to start at brighter

light level

END. AGC 0

* Set stop level of noise reduction

* Higher level allows 3 DNR to start at brighter

light level

7. SPECIAL

SPECIAL

DEFAULT

DESCRIPTION

CAM TITLE

OFF

* If set to ON, camera title is displayed.

D-EFFCT

* Can set FREEZE, MIRROR, D-ZOOM, SMART

D-ZOOM, NEG.IMAGE & DIS.

MOTION OFF

* Programmable up to 4 areas. If motion is

detected, mosaic effect appears.

PRIVACY

OFF

* Programmable up to 8 masked areas.

LANGUAGE ENG

* Support 16 languages, ENG / JPN / CHI1 / CH2

/ KOR / GER / FRA / ITA / SPA / POL / RUS /

POR / NED / TUR / HEB / ARB

* To change the language, push ● (SET/ENTER).

It will be taken about 4seconds to load new

language fonts.

DEFECT

* Defect pixels in the image sensor is

compensated and remapped.

RS485

* Set RS485 for remote control.

CAM ID & BAUDRATE

7. SPECIAL

7-1. CAM TITLE

* I

nput max.15 characters or symbols by using▲ (up)/▼ (down)/◀ (left)/▶ (right) buttons.

* Press ● to select and the selected character/symbol will be displayed on the input line

* → ←: move CAM TITLE input position

* CLR: remove all inputted characters and symbols

* POS: move and set CAM TITLE display position

* END: finish and return to menu

7-2. D-EFFECT

D-EFFECT

DEFAULT

DESCRIPTION

FREEZE OFF

* freeze image and shows still image when set to

MIRROR OFF

* OFF : normal image display

* MIRROR / V-FLIP / ROTATE(H/V FLIP)

* Cannot use if FREEZE is set to ON.

D-ZOOM OFF

* Available max. 62x digital zoom.

* PAN/TILT : set zoom position by moving

UP / DOWN / LEFT / RIGHT.

* Usable at 30/25P resolution.

Cannot synchronize with SMART D-ZOOM but

usable either D-ZOOM

SMART

D-ZOOM

When motion is detected camera will digitally

zoom in

NEG.IMAGE

OFF

* If set to ON, shows negative image

DIS

* Digital Image Stabilizer. Available at A-30/25P

set up (will lose part of image)

7-2.

�D-ZOOM

D-ZOOM

DEFAULT

DESCRIPTION

D-ZOOM X2.0

2~64 X digital zoom, area can be scanned by

using Pan/Tilt

PAN/TILT

*Set zoom position by moving UP / DOWN / LEFT

/ RIGHT

DEFAULT

* Reset all changes in the menu

1). When entering or exiting D-Zoom video will be lost for a second so that the camera

can adjust to new setting

2). CVBS (Sub-Video) is off at D-ZOOM “ON”

Page is loading ...

Vitek VTC-BHOC6R4F User manual

Brand: Vitek

Model: VTC-BHOC6R4F

Category: Security cameras

Type: User manual

Download PDF

report

Vitek VTC-BHOC6R4F User manual

Vitek VTC-BHOC6R4F User manual

Related papers

Other documents