Vitek VTC-C2BTS1 User manual

Brand: Vitek

Model: VTC-C2BTS1

Category: Security cameras

Type: User manual

FEATURES:

• 1/2.7” Progressive Scan CMOS Sensor

• 2.1 MegaPixel with Full 1080p TVI Output

• Small scale design to fit in 5” dome enclosures such as the Pelco® DF5

Housing

• Sensitivity of 0.08 Lux

• 2D-DNR Digital Noise Reduction

• True Day/Night by ICR (Infrared Cut Removal)

• Built-in Motion Detection with a 24x16 Grid

• Privacy Mask function with programmable mask areas

• 12VDC / 24VAC Dual Voltage Operation

• Lenses Sold Separately

VTC-C2BTS1

2.1MP Premium TVI Compact

Box Camera

VITEK

Safety Precaution

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

To prevent electric shocks and risk of fire hazards, do NOT use other than

specific power source.

Warning :

This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

Caution :

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority

to operate the equipment.

Mains power quality should be that of a typical commercial environment. If the user

of the model requires continued operation during power mains interruptions, it is

recommended that the model be powered from an uninterruptible power supply

(UPS) or a battery.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of uninsulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

2 3

Safety Precaution

NOTICE

The image used in this instruction manual are processed to help comprehension

and may differ from actual video of the camera.

Avoid installing areas where has shock or vibration which results in the problems.

Pay attention to safety when laying the connection cable and observe that the cable

is not subjected to heavy loads, kinks or damage and no moisture can get in.

Never open the device such as boards.

The warranty becomes void if repairs are undertaken by unauthorized persons.

Maintenance and repair have to be carried out only by authorized service centers.

Use only a mild detergent to clean the housing.

The camera should never be operated beyond the technical specifications.

This can lead to destruction.

The camera should never be operated in water.

Contents

Safety Precaution

p.02~03

Contents

p.04

Features

p.05

Composition

p.06

Dimensions

p.06

Part Names

p.07

Installation Instructions

p.08~09

Operating Instructions

p.10~19

Specifications

p.20

4 5

Features

Key Features

• 1/2.7” CMOS Sensor

• Full-HD 2Mega pixel HD-TVI CAMERA, 1920x1080(30p)

• TVI Video Transmission Distance over Coax.; 500M (RG59, 75Ω)

*depending on cable condition and characteristics

• Automatically removable IR Cut filter by Dual filter switcher

• CS mount supported (Option: C-mount adaptor)

• Sensitivity of 0.08 Lux (AGC 3)

• Improved noise reduction 2DNR

• LSC (Lens Shading Compensation)

• Motion detection, Privacy mask, BLC/HLC, Flickerless, H/V/HV Flip

• UTC control through HD-TVI DVR (Pelco-C)

• Back focus Flange

• Built-in OSD MENU

• Reverse polarity protection circuit

• Isolated power supply against ground loop problem

• Power: AC24V/DC12V

L- Wrench:

1.5mm (1pc)

Dust Protection

Cap (1pc)

Operating

Instruction

Compact Box Camera

1.73”

2.09”

1.89”

Ø1.81”

2.38”

2.89”

Dimensions

Composition

6 7

Part Names

L-Wrench

Dust

Protection Cap

No.

DC Iris

Damp(-)

Damp(+)

Drive(+)

GND

Flange Lock screw

Front Case

Rear Case

Back focus

adjusting Flange

Mount Holes

(Top / Bottom)

REAR VIEW

Lens Connector

for Auto Iris lenses

① Video out connector(BNC)

② Power input terminal

③ OSD Control Joy stick

④ DC Auto Iris Lens connector

④

③

①

②

PIN 1PIN 3

PIN 2PIN 4

Installation Instructions

CAUTION

Installation Instructions

• Make sure the power is removed before installation

1. Remove the dust protection cap from the lens mount.

2. Screw the lens onto the camera firmly.

3. Plug the lens plug into the lens connector on the rear of camera case.

4. Mount the camera to the wall or ceiling with a corresponding mounting bracket

through the camera mount holes (1/4” thread insert) on its top or bottom

• Follow this order for applying power.

First connect the low voltage cable (DC12V or AC24V), then plug the AC adapter

into AC outlet to avoid damage from the surge voltage with no load.

• Care should be taken the cable is NOT damaged, kinked or exposed in

hazardous areas.

• Do not expose the camera lens directly to a strong light source such as the sun or

spot light.

Setting the back focus adjustment

For easier and better adjustment, this camera provides FOCUS ADJUST menu

which helps with focusing the camera.

When enabling FOCUS ASSIST menu, follow the procedure to get the best back

focus adjustment.

1. Set the lens for the zoom position to WIDE and the focus position to INFINITE(∞).

2. Point at an object 30' away

3. Adjust ’Back focus adjusting Flange’ until the optimum focus is achieved.

4. Set the lens for zoom position to TELE and adjust the lens focus for best focus.

5. Set the lens for zoom position to WIDE again, check if the focus adjustment

is the best. If not, re-adjust ‘Back focus Flange’ slightly.

6. After setting, tighten the ‘Flange lock screw’ with L-wrench supplied.

Start up

When the camera is powered properly, it starts up with initializing the internal

parameters.

8 9

Installation Instructions

Using OSD Controller

Setup menu can be accessed and controlled by OSD control joy stick on the

rear of the camera unit.

Five commands are available with the joy stick.

The design of rear panel could be different according to the camera models.

Description of the joystick operation

1) SET Key (●) : Access to the menu or enter the setting.

To enter the main menu, press the Set Key down for about 1.5sec

2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move

the cursor up or down.

3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.

Use to adjust the desired menu selection and to move the cursor left

or right.

Operating Instructions

OSD menu Startup

• EXIT : Enters ‘EXIT’ menu.

• RETURN : Returns to the previous menu.

Press the ‘OSD menu SET key’ down to access the setup menu mode.

MAIN MENU

> 1. VIDEO OUT

2. DAY / NIGHT

3. AWB

4. AE

5. SPECIAL

6. EFFECT

7. SYSTEM

8. EXIT

OSD menu Table

MAIN MENU SUB MENU CONFIGURATION

VIDEO OUT

DAY/NIGHT

AWB

FRAME RATE

RETURN

MODE

30 / 25

1~63

1~60 SEC

COLOR

B&W

AUTO

USER

AUTO

EXT

D TO N

N TO D

DELAY TIME

RETURN

IN/OUT DOOR

RETURN

RED GAIN

GREEN GAIN

IN, OUT

1~255

10 11

Operating Instructions

AWB

SPECIAL

MODE

PUSH

8000K

6000K

4200K

3200K

HOLD

MODE

BRIGHT

SHUTTER

FLICKER

BLC

AGC

LSC

RETURN

USER

R-GAIN

B-GAIN

RETURN

PRIVACY ZONE

MOTION

HLC

RETURN

BLUE GAIN

RETURN

AREA SEL.

MASK PAT.

RETURN

AREA1, AREA 2

OFF, BLACK, GRAY, WHITE

0~240

0~135

OFF, ON

0~255

OFF, TRACE, ICON

1~10 SEC

DC, ESC, HOLD

0~255

AUTO, 1/25, 1/30, 1/50, 1/60, 1/100, 1/120, 1/250, 1/500,

1/1000, 1/3000, 1/10000

1~255

OFF, 50Hz, 60Hz

0~16

1~5

ON, OFF

MOTION

SENSITI.

ALARM

HOLD TIME

RETURN

HLC

MASK VALUE

THRESHOLD

RETURN

OFF, ON

0~255

AREA SET

Operating Instructions

MAIN MENU

> 1. VIDEO OUT

2. DAY / NIGHT

3. AWB

4. AE

5. SPECIAL

6. EFFECT

7. SYSTEM

8. EXIT

VIDEO OUT

> 1. FRAME RATE : 30

2. RETURN

OSD menu Setup

1. VIDEO OUT

EFFECT

SYSTEM

EXIT

COLOR GAIN

COLOR HUE

SHARPNESS

CONTRAST

BRIGHT OFF.

MIRROR

FLIP

RETURN

CAMERA ID

ID DISP

NAME DISP

LANGUAGE

FACTORY INIT

RETURN

SAVE/EXIT

EXIT

RETURN

0~255

0~71

0~255

-128~127

OFF, ON

OFF,ON

0~255

OFF, ON

OFF,ON

ENG, CHINESE

OFF, ON

Selects HDTV standards for video output switches to FRAME RATE 30(NTSC)

or 25(PAL)

accordingly.

12 13

Operating Instructions

DAY/NIGHT is used to control the setting during day-time and night-time

operation. Select the mode according to the light condition and the camera

types.

2-1-3. AUTO

Used when DAY or NIGHT is determined by light level through the lens and

DAY from/to NIGHT is switched automatically by the scene brightness.

Sets the threshold level switching from/to DAY(color) or NIGHT(B/W).

Setting at a low level makes the camera enter NIGHT at a lower light level.

High level makes the camera exit NIGHT at a higher light level.

2-1-2. B/W

The camera is always in B/W mode.

Forcibly removes IR cut filter and switches to B/W regardless of light level.

2-1-1. COLOR

2-1. MODE

The camera is always in COLOR mode.

Forcibly DAY/NIGHT is disabled and outputs color video.

2-2. D TO N : 1~63

DAY / NIGHT

> 1. MODE

2. D TO N

3. N TO D

4. DELAY TIME

5. RETURN

: [EXT]

: 55

: 35

: 3SEC

2. DAY / NIGHT

2-1-4. EXT

DAY or NIGHT is determined by the built-in light photo sensor.

Camera with IR LED must be set to EXT.

Operating Instructions

Automatically tracks the changes of color temperature and continuously

adjusts the white balance.

> OUT : Optimized for outdoor sunlight applications and easily

compensates AWB for high color temperature such as sunlight.

> IN : Optimized for Indoor installation and easily compensates AWB

for low color temperature such as incandescent lights.

Sets the delay time when the camera switches from/to DAY(color)

or NIGHT(B/W).

3-1-1. AUTO : IN/OUTDOOR

3-1. MODE

The camera is automatically set to INDOOR or OUTDOOR environments.

Sets the gap level switching from/to DAY(color) or NIGHT(B/W).

2-3. N TO D : 1~63

2-4. DELAY TIME : 1~60SEC

AWB

> 1. MODE

2. R-G GAIN

3. B-G GAIN

4. RETURN

: [AUTO]

: 128

AWB > AUTO MODE

> 1. IIN/OUT DOOR

2. RETURN

: OUT

3. AWB

White balance is fixed to the settings by Red, Green and Blue_GAIN.

This mode can be used only when the color temperature does not vary.

3-1-2. USER

3-1-3. PUSH : White balance is performed only whenever ‘PUSH’ is selected.

3-1-4. 8000K : Set the white balance range by 8,000°K.

14 15

Operating Instructions

Lens can be selected either DC or MANUAL lens.

Lens MUST be set to DC for the best image when DC iris lens is installed

White balance is fixed to the settings of Red-Green GAIN.

White balance is fixed to the settings of Blue-Green GAIN.

3-2. R-G GAIN : 1~255

3-3. B-G GAIN : 1~255

4-1. MODE

3-1-5. 6000K : Set the white balance range by 6,000°K.

3-1-6. 4200K : Set the white balance range by 4,200°K.

3-1-7. 3200K : Set the white balance range by 3,200°K.

3-1-8. HOLD : Fixed white balnce.

4-1-1. DC :

4-1-2. ESC : Set the Electric Shutter Control

4-1-3. HOLD : Fixed exposure.

> 1. MODE

2. BRIGHT

3. SHUTTER

4. FLICKER

5. BLC

6. AGC

7. LSC

8. RETURN

: DC

: 128

: AUTO

: OFF

: 0

: 5

: OFF

4. AE

: Selects lens mode according to installation conditions.

Increases or decreases the brightness of the picture.

This is different from that of DC iris lens and simply increases or decreases

the digital gain of video. Do not increase this too much, the dynamic range

for the bright areas will decrease.

4-2. BRIGHTNESS : 0~255

AE(Auto Exposure) menu provides the parameters which control the light level

and enhance the dynamic range of video.

Operating Instructions

4-5. BLC : 0~16

BLC(Back Light Compensation) is used to brighten an image in the fore-

ground with a bright area behind it such as sunlight, limiting the affect

of silhouette. Set the BLC level from 0 to 16.

Sets the PRIVACY Zone, AREA1 or 2 are available and each area is pro-

grammable in size, color and position.

PRIVACY ZONE

> 1. AREA SEL.

2. MASK PAT.

3. SX

4. EX

5. SY

6. EY

7. RETURN

SPECIAL

> 1. PRIVACY ZONE

2. MOTION

3. HLC

4. RETURN

5. SPECIAL

5-1. PRIVACY ZONE

5-1-1. AREA SEL. : Area1, Area2

4-3-1. AUTO: Optimizes the video level by controlling the iris and the shutter

speed automatically.

4-3-2. 1/30(1/25), 1/60(1/50), 1/120(1/100), ~ 1/10000: Shutter can be set to fix.

Reduces the flicker in video when NTSC/PAL mode is used in 50Hz / 60Hz

fluorescent lighting respectively.

Select Shutter speed, AUTO or manual.

4-3. SHUTTER

4-4. FLICKER

AGC(Auto Gain Control) can be set from 1 to 5 levels.

4-6. AGC

: 1~5

LSC(Lens Shade Compensation) is used to caculate the compensation data

for lens shading. Convex shape of the lens causes the light to enter the

camera unevenly and typically makes the center of the screen brighter than

the rest. It is used to compensate for this undesirable effect and make the

screen more even.

4-7. LSC

: AREA1

: WHITE

: 16

: 32

: 16

: 32

16 17

Operating Instructions

If set to ON, motion is displayed on the monitor by means of digital effect.

Sets the detection sensitivity for motion. High value increases the sensitivity

to detect small motion easily. Too low will cause erratic detection by

tree leaves or light level changes.

MOTION

> 1. MOTION

2. SENSITI.

3. ALARM

4. HOLD TIME

5. RETURN

SPECIAL

1. PRIVACY ZONE

> 2. MOTION

3. HLC

4. RETURN

5-2-1. MOTION : OFF, ON

5-3-1. HLC : OFF, ON

5-2-2. SENSITI. : 0~255

Set to OFF, TRACE, ICON for motion alarm display.

5-2-3. ALARM : OFF, TRACE, ICON

Sets the interval time from the starting of motion operation until being ready

for the next motion operation.

5-2-4. HOLD TIME : 1~10 SEC

5-2. MOTION

5-3. HLC

Selects the mask color pattern Area 1 or 2

5-1-2. MASK PAT. : Off, Black, Gray, White

5-1-3. SX, EX. : Set the X-position or size for the selected arear (Start-X, End-X)

5-1-4. SY, EY. : Set the Y-position or size for the selected arear (Start-Y, End-Y)

: OFF

: 32

: OFF

: 1SEC

HLC (High Light Cut out) is used to black out bright areas, in order

to enable a clear visual image of objects.

Set to ON, select window for HLC.

5-3-2. MASK VALUE : 0~255

Set the transparency rate for the HLC mask.

Operating Instructions

HLC > AREA SET

> 1. AREA SET

2. RETURN

X X <O> X

X X X X

HLC

> 1. HLC

2. MASK VALUE

3. THRESHOLD

4. RETURN

6-1. COLOR GAIN : 0~255

EFFECT

> 1. COLOR GAIN

2. COLOR HUE

3. SHARPNESS

4. CONTRAST

5. BRIGHT OFF.

6. MIRROR

7. FLIP

8. RETURN

: 60

: 0

: 10

: 128

: 0

: ON

6. EFFECT

: ON

: 32

: 250

Defines the threshold level for HLC. Lower value masks more.

5-3-3. THRESHOLD : 0~255

Increases or decreases the color saturation.

6-2. COLOR HUE : 0~71

Increases or decreases the sharpness of the picture.

Too much sharpness can make image harsh and show more noise as well

as line flicker at the edge of objects in the picture.

Adjusts hue of the picture.

6-3. SHARPNESS : 0~255

6-4. CONTRAST : 0~255

Adjusts the strength of the image contrast. If set to too high, the dark area

may loss detail and the bright area may saturate.

18 19

Operating Instructions

6-5. BRIGHT OFF : -128~127

Controls the brightness of the image, to high of setting will cause more noise

in the picture

6-6. MIRROR : OFF, ON

Mirrors the video signals vertically.

6-7. FLIP : OFF, ON

7-1. CAMERA ID : 0~255

7-2. ID DISP. : OFF, ON

7-3. NAME DISP. : Not supported.

Flips the video signals horizontally.

SYSTEM

> 1. CAMERA ID

2. ID DISP.

3. NAME DISP.

4. LANGUAGE

5. FACTORY INIT.

6. RETURN

: 0

: OFF

: ENG

: OFF

7. SYSTEM

Set number for the Camera ID.

8-1. SAVE / EXIT : Save all the settings and exit the setup menu.

8-2. EXIT : Exit the setup menu without saving.

8. EXIT

Set ON/OFF for enabling/disabling of camera ID.

7-4. LANGUAGE

Select camera OSD menu language English or Chinese.

7-5. FACTORY INIT

If set to ON, all the camera setting are restored to the factory defaults.

Detailed Specifications

Imaging Sensor

Video Output

Resolution

Effective Pixels

S/N Ratio

Sensitivity

Lens Type

DAY / NIGHT

White Balance

DNR

Advanced OSD Features

Remote Control

Operating Conditions

Input Voltage

Power Consumption (12VDC)

Power Consumption (24VAC)

Weight

Dimensions (W x H x L)

1/2.7” Progressive Scan CMOS Sensor

HD-TVI by BNC

2.1 MegaPixel (1080p)

1920(H) x 1080(V) x 30p

More than 52dB with AGC Off at 50 IRE

0.08 Lux (AGC 3)

CS Mount Lens Support

Mechanical IR Cut Filter (True Day/Night)

Auto / User / Push / Hold

2D-DNR

BLC/HLC, Motion detection, Privacy mask, Flickerless, LSC (Lens Shading

Compensation), Flip

UTC by HD-TVI DVR (Pelco-C)

14°~122°F (-10°~ +50°C) < 80% RH

12VDC / 24VAC (Dual Voltage)

185mA @ 12V (2.2W)

100mA

5.43 Oz. (154g)

1.89” x 2.09” x 2.89” (48 x 53 x 73.5mm)

20 21

Page is loading ...

Vitek VTC-C2BTS1 User manual

Brand: Vitek

Model: VTC-C2BTS1

Category: Security cameras

Type: User manual

Download PDF

report

Vitek VTC-C2BTS1 User manual

Vitek VTC-C2BTS1 User manual

Related papers

Other documents