iCraig CSH307 Owner's manual

1

2

3

4

5

This manual contains important safety precautions and information for correct usage. Please be

sure to read this manual carefully before use to avoid any damage to the device.

Do not place the product in hot, wet or dusty environments.

Do not place the product for outdoor usage.

Avoid dropping or smashing the product.

Select a suitable product with correspondent maximum load of current upto 15A.

Notes:

This device is not waterproof.

All images in this manual are for reference only. Specifications and appearance of the product

are subject to change without prior notice.

6

1. Location of Controls

1. IR LED

2. System LED (Blue)

3. MIC

4. PIR (Passive infrared sensor)

5. POWER LED (Red)

6. MICRO USB (For Power Supply)

7. MICRO SD Card Slot

8. Reset (After 15 seconds to return to default setting including password)

9. Antenna

2.GETTING STARTED

Congratulations on buying a iCraig Camera. This device will enable you to easily

check your loved ones by viewing them while you are away.

1.Initial Setup

To get started, you will need:

Your wireless router, its network name, and password if necessary.

7

An Android™ Smart Phone or Tablet ( Android Version 4.0 or later) or an iPhone,

iPad, or iPod touch (iOS Version 6.1 or later).

Make sure your Smart phone or tablet, the wifi status is ON.

2.Plug the iCraig Cam into a power outlet.

Insert the micro USB cable ( included) to the Micro USB jack on the device. Plug the full size

USB jack of connection cable to supplied AC/DC USB Adaptor to wall outlet having AC 100-

240V~, 50/60 Hz.

Using the supplied AC/USB Adaptor for Power Supply. Other models charger may damage the

device.

3.Download the iCraig SMART App from the App Store or Google Play.

8

After installing your app, open the APP, press and to choose “Add new online

Camera”icon to activate the APP.

4.Check your iCraig cam LED lights which indicate the status as below:

Blue LED Light “Slow Flash” ==== Ready for new connection mode.

Blue LED light “Fast Flash”=== In progress for connection

Blue LED light “Solid blue live”=== connected.

3. Connect IP Camera at AP (Access Point) Mode

There are two methods to setup your iCraig IP camera – connection without

QR scan and connection by UID (QR Code) scan. Both methods require

connect your smartphone with IP camera at AP (Access Point) mode. See

below:

When the iCraig Cam Blue LED light is flashing slowly, Go to “Settings -----> Choose

“Wi-Fi” on your Smart Phone or tablet to look for the wifi name similar to “

PQXXXXX_XXXXXXXXXXXX_XXXXXX”

9

Connect to your Camera with the Phone or tablet

Tap on the Camera wifi name appear on your phone to connect the device. After a

success connection, your phone will show the camera WIFI name on your screen as

connected wifi.

10

4. Method 1 – connection without QR Scan

(Make sure IP camera Access Point is Connected with Smartphone)

Open the APP Choose “+” on the top right screen, then Tap on “Add new

online Device”.

Tap on “Search(LAN)” , all connected camera will display on your screen.

Tap on camera you want to connect and press “OK” to connect. Wait until the new

camera Logging in successfully, you will see the camera online status appear on

your screen. Now app connected with IP camera through AP (Access Point) mode.

11

Connect IP Camera to WIFI network

Tap the Setting icon” ” on Live Cam page (see as below) and choose the

“advance Config”.

Tap the “WIFI Config” and choose your wifi network by identifying your network

name.

Input your wifi network password if needed.

12

Tap “OK”, it will display confirmation message if all required wifi name/password is correct.

Then touch “OK”, the camera will start to reboot. Once complete, it shows “Device

reboot”

The new camera will logging in to your home network automatically, wait until the

camera appears “online, X User” (blue word) successfully. Now it is finish setup.

13

5. Method 2 - connection by UID (QR Code) Scan (Make sure IP

camera Access Point is Connected with Smartphone)

This is another method to connect IP camera by QR code scan, procedure as

below:

Open the APP Choose “+” on the top right screen, then Tap on “Setup Device

WIFI connection”.

14

Locate your QR Code label on the back of wifi camera which is similar to this “ ”

use your Smart Phone to aim on the QR code after pressing the QR SCAN icon on

the APP screen.

Choose your wifi network by identifying your network name

Input your wifi network password if needed.

Press “Start Configuring Wifi” icon to start connection.

15

Wait until the “Add New Device” icon display on app screen, and then touch it. You

can see new connected device shows on “Search Device” page (see below)

Tap the new device then Press “OK”, the new camera will logging in, wait until the

camera appear “online, X User” (blue word) successfully. Now it is finish setup.

16

6. Reset (Reset button on rear of camera)

If you want to connect IP camera with other network or camera works abnormally.

You can press and hold “reset button” locate at rear of camera 15 seconds to reset it

as manufacturer stage (erase all network data and P2P password will set to

manufacturer default (8888).

7.Other Functions

Touch the camera screen on your smartphone, it will appear control panel as below:

Use small metal pin to

press and hold reset

button 15 secs to reset

as manufacturer default.

17

High

The current frame image quality is high

Normal

The current frame image quality is normal.

Low

Bandwidth

The quality of the low bandwidth when the current frame image

Adjust the brightness

Adjust the contrast

Open and Close MIC

No function

Smartphone Screenshot

Smartphone Record

NO FUNCTION

The current frame mirror left and right

The current picture mirror up and down

8.Settings:

Tap the Setting icon “ ” on your Live Cam page, see below pictures

Choose Modify Camera to rename the camera.

Choose Delete the camera stored in this app.

Choose reconnect to reconnect your camera online again.

18

Tap on Advance Configs Set Up:

Alarm Config

Select motion detection sensitivity by pressing on the icon and sensitivity screen will

pop up for you to choose.

Choose disable if you do not wish to have this alert.

- To set up motion detection by enabling PIR sensor by sliding the icon to the right

hand side.

19

To record on your micro SD card (Micro SD is not

included)

Change P2P password:

- Default password: 8888 and you may change the password with 4 to 10 digits.

**If you have forgotten the password, press the RESET button on the back of

the device for about 15s.

1. Insert the Micro SD card and format.

2. Choose Record Resolution before

using this feature

3. Choose File Length to set your

recording time

4. Tap “OK” to enable recording

20

Time Setting:

To sync with the smart phone and the app on real time by pressing “Device Time

Sync

with App”.

Page is loading ...

iCraig CSH307 Owner's manual

iCraig CSH307 Owner's manual

Other documents