Task Force Tips ABD3SP-NT Operating instructions

Brand: Task Force Tips

Model: ABD3SP-NT

Type: Operating instructions

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

MANUAL: Low Proﬁ le Ball

Intake Valve

INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE

WARNING Understand manual before use. Operation of this device without understanding the manual

and receiving proper training is a misuse of this equipment. Obtain safety information at

tft.com/serial-number

TASK FORCE TIPS LLC

MADE IN USA • tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

OPERATING RANGE:

Pressure Max 300 PSI (20 bar)

Pressure Min Full Vac.

NFPA 1962 Test Pressure

300 PSI (21 bar)

Six seconds from open to close

meets NFPA 1901

slow close requirement.

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

DANGER

PERSONAL RESPONSIBILITY CODE

The member companies of FEMSA that provide emergency response

equipment and services want responders to know and understand the

following:

1. Fireﬁ ghting and Emergency Response are inherently dangerous activities

requiring proper training in their hazards and the use of extreme caution

at all times.

2. It is your responsibility to read and understand any user’s instructions,

including purpose and limitations, provided with any piece of equipment

you may be called upon to use.

3. It is your responsibility to know that you have been properly trained in

Fireﬁ ghting and /or Emergency Response and in the use, precautions, and

care of any equipment you may be called upon to use.

4. It is your responsibility to be in proper physical condition and to maintain

the personal skill level required to operate any equipment you may be

called upon to use.

5. It is your responsibility to know that your equipment is in operable

condition and has been maintained in accordance with the manufacturer’s

instructions.

6. Failure to follow these guidelines may result in death, burns or other

severe injury.

FEMSA

Fire and Emergency Manufacturers and Service Association

P.O. Box 147, Lynnﬁ eld, MA 01940 • www.FEMSA.org

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

Table Of Contents

1.0 MEANING OF SIGNAL WORDS

2.0 SAFETY

3.0 GENERAL INFORMATION

3.1 SPECIFICATIONS

3.2 CORROSION

3.3 USE WITH SALT WATER

4.0 INSTALLATION

4.1 MOUNTING THE VALVE

4.2 CHANGING OFFSET OF CRANK HANDLE

4.3 CHANGING COUPLING LOCKOUT

4.4 STORZ ‘SUCTION GASKET’ REQUEST

5.0 USE

5.1 VALVE OPERATION

5.2 AIR VENT AND WATER DRAIN

5.3 PRESSURE RELIEF VALVE

5.3.1 SETTING RELIEF VALVE PRESSURE

5.4 PRESSURE LOSS

5.5 SUCTION SCREEN

6.0 EXPLODED VIEWS AND PARTS LISTS

6.1 BALL INTAKE AXD SERIES EXPLODED VIEW AND PARTS LIST

6.2 SIDE B OPTIONS EXPLODED VIEWS AND PARTS LISTS

6.3 AIR VENT/DRAIN [B] EXPLODED VIEW AND PARTS LIST

6.4 PRESSURE RELIEF VALVE EXPLODED VIEW AND PARTS LIST

7.0 TROUBLE SHOOTING

8.0 WARRANTY

9.0 MAINTENANCE

9.1 SERVICE TESTING

9.1.1 HYDRAULIC TESTING

9.1.2 RELIEF VALVE TEST

9.1.3 SHUTOFF VALVE

9.1.4 RECORDS

9.2 CRANKSHAFT OVERRIDE & REPLACEMENT

9.2.1 CRANKSHAFT OVERRIDE

9.2.2 DIAGNOSIS

9.2.3 CRANKSHAFT REPLACEMENT

10.0 REPAIR

11.0 ANSWERS TO YOUR QUESTIONS

12.0 INSPECTION CHECKLIST

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

1.0 MEANING OF SIGNAL WORDS

A safety related message is identiﬁ ed by a safety alert symbol and a signal word to indicate the level of risk involved with a particular

hazard. Per ANSI standard Z535.6-2011, the deﬁ nitions of the four signal words are as follows:

DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor

or moderate injury.

NOTICE NOTICE is used to address practices not related to physical injury.

2.0 SAFETY

WARNING Quick changes in valve position can cause high pressure spikes due to water hammer and may

result in damaged equipment which could lead to injury or death. Open and close the valve

slowly to avoid water hammer.

WARNING Injury or death can result from burst hoses and ﬁ ttings. Risk can be minimized by the proper care

and use of hose and appliances per NFPA 1962. The relief valve must be set to an appropriate

pressure based on the type of hose and equipment you are using.

WARNING Injury or death may occur by attempting to use a damaged Valve. Per NFPA 1962, the device shall

be inspected and tested at least quarterly. Before use inspect for damage resulting from:

• Failure to drain valve followed by exposure to freezing conditions

• Exposure to temperatures in excess of 160 degrees F

• Missing parts, physical abuse

WARNING This equipment is intended for use by trained personnel for ﬁ reﬁ ghting. Its use for other

purposes may involve hazards not addressed by this manual. Seek appropriate guidance and

training to reduce risk of injury.

WARNING Kinks in supply hose may reduce water ﬂ ow and cause injury or death to persons dependant on

water ﬂ ow. Avoid tight bends to minimize risk of hoseline kinks.

WARNING The appliance may be damaged if frozen while containing signiﬁ cant amounts of water. Such

damage may be diﬃ cult to detect visually and can lead to possible injury or death. Any time the

appliance is subject to possible damage due to freezing, it must be hydrostatically tested by

qualiﬁ ed personnel before being considered safe for use.

CAUTION Maximum operating pressure for the valve is 300 PSI (20 bar). Do not exceed 300 PSI on either

side of the valve.

CAUTION Valve must be properly connected. Mismatched or damaged connectors may cause leaking or

uncoupling under pressure and could cause injury.

CAUTION Any alterations to the valve and its markings could diminish safety and constitutes a misuse of

this equipment.

NOTICE Use with salt water is permissible provided the valve is thoroughly cleaned with fresh water after

each use. The service life of the valve may be shortened due to the eﬀ ects of corrosion and is

not covered under warranty.

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

3.0 GENERAL INFORMATION

The Low Proﬁ le Ball Intake Valve is intended for use on either the intake manifold of a ﬁ re engine or on a discharge port of a ﬁ re main.

The valve is available in versions to minimize interference with surrounding components. The valve is kept closed while the water

supply from a hydrant or another pumper to the engine is being established. This prevents the pump from sucking air through the

intake manifold and losing its prime. Once the supply hose is ﬁ lled and under pressure, and the air has been vented from the hose,

the valve may be opened to connect the pump to the water supply. An adjustable pressure relief valve mounted on the valve opens to

relieve any excess pressure that may damage the hose or the pump. The valve may be used for pressure or vacuum/drafting service.

Hand Crank

Pressure Relief Valve

Air Vent & Drain

Intake

Side B Coupling

Valve Position

Indicator

Outlet

Side A Coupling

Figure 3.0 ABD3ST-NX

Low Proﬁ le Ball Intake Valve

With Pressure Relief Valve

3.1 SPECIFICATIONS

MODEL LOW PROFILE VALVE

Waterway Size 3.65” (93mm)

Max Pressure 300 psi (20 bar)

Min Pressure Full Vacuum

Temperature Rating* -25°F to 135°F (-32°C to 57°C)

Opening/Closing Speed Meets NFPA 1965 Slow Close Requirements

3.2 CORROSION

Aluminum parts are hard anodized. All castings are then powder coated inside and out to help prevent corrosion. Hose couplings are

attached using polymer bearing rings which provide electrical insulation to help prevent galvanic corrosion. The eﬀ ects of corrosion

can be minimized by good maintenance practice. See section 9.0 for MAINTENANCE.

3.3 USE WITH SALT WATER

Use with salt water is permissible provided valve is thoroughly cleaned with fresh water after each use. The service life of the valve

may be shortened due to the eﬀ ects of corrosion and is not covered under warranty.

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

4.0 INSTALLATION

4.1 MOUNTING THE VALVE

Screw the large coupling to a pump manifold or ﬁ re water discharge port and tighten securely. The valve position indicator should be

clearly visible, but need not be level.

CAUTION Dissimilar metals coupled together can cause galvanic corrosion that can result in the inability

to unscrew the threads and complete loss of thread engagement over time. Per NFPA 1962 (2013

edition), if dissimilar metals are left coupled together an anti-corrosive lubricant should be applied

to the threads. Also, the coupling should be disconnected and inspected at least quarterly.

4.2 CHANGING OFFSET OF CRANK HANDLE

When equipped with a crank handle, two oﬀ set positions are available

to adjust the swing radius of the crank and knob as shown in ﬁ gure

4.2. The longer oﬀ set position oﬀ ers reduced eﬀ ort to operate the

valve. The shorter oﬀ set is available to avoid interference with other

equipment on the apparatus. To change the oﬀ set, remove two 1/4”-

20 x 1/2” button head cap screws from crank. Place crank in desired

position and replace screws. Apply Blue Loc-Tite thread locking

compound to all of the screw threads.

Longer Offset Position

2.6" [67mm]

Swing Radius

Shorter Offset Position

1.6" [41mm]

Swing Radius

Figure 4.2

Crank Handle Oﬀ set

4.3 CHANGING COUPLING LOCK-OUT

To change a coupling from rigid to full time swivel, use a

7/32” Allen driver to back out the lockout screw until the

coupling moves freely.

To change a coupling from full time swivel to rigid, Rotate

the coupling until the lockout screw is aligned with the

Air Vent/Bleed Valve on the top of the valve body. Use

a 7/32” Allen driver to tighten the lockout screw into the

lockout divot in the elbow. Do not tighten the screw onto

the polymer bearing strip.

Lock-Out Screw

Figure 4.3.

Coupling Lock-Out

4.4 STORZ ‘SUCTION GASKET’ REQUEST

If your application of this product requires drafting, you may need a suction gasket. Please call 1-800-348-2686 to receive a free

suction gasket by mail.

Part Numbers: 4” STORZ - item # A4216, 5” STORZ - item # A4221, 6” STORZ - item #A4273

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

5.0 USE

5.1 VALVE OPERATION

The valves covered by this manual utilize positive stops at the OPEN and CLOSED positions. Attempting to close a valve further than

the positive stops will not result in a tighter seal between the ball and valve seat. All valves include markings to indicate the direction

of handle rotation to open the valve.

Valves with hand cranks include a valve position indicator. To open the valve, turn the hand crank until the valve position indicator

shows OPEN. To close the valve, turn the hand crank the opposite way until the valve position indicator shows CLOSED.

CLOSED

OPEN

CLOSED

Figure 5.1

Valve Position Indicator

Up to the maximum rated pressure, operating torque should never exceed the values in the table below. If greater torque is required

to operate the valve, then that is an indication that the valve needs maintenance. Exceeding 30 ft-lb / 41 N-m torque may damage

the appliance. Kicking or standing on the valve controls is considered misuse of the appliance.

Valve Seat Bore

Size

Max. Acceptable

Torque

Max. Acceptable

Force on Knob

3.65 in 93mm 12 ft-lb 16 N-m 45 lb 20 kg

Exceeding 45 ft-lb will cause one side of the crank shaft to shear oﬀ . This is intentional to prevent further damage to the gearbox. If

the shaft shears oﬀ , the valve can be operated temporarily using a wrench on the ½” hex on the opposite side of the crankshaft. For

repair instructions, see section 9.2 CRANKSHAFT OVERRIDE AND REPLACEMENT.

5.2 AIR VENT AND WATER DRAIN

CAUTION Loss of prime can interrupt water ﬂ ow and cause injury or death. Always bleed out air with air

valve to prevent possible loss of prime.

The BIV-LP comes with an Air Vent/Drain Valve situated on the top of the valve.

5.3 PRESSURE RELIEF VALVE

WARNING Do not leave the pressure relief valve in the OFF position. The pressure relief valve is disabled in

the OFF position and oﬀ ers no protection against over pressurization. The OFF position may be

used for controlled pump testing but should not be used for service conditions. Exercise great

care to avoid water hammer or other pressure spikes when the pressure relief valve is in the OFF

position.

WARNING The Pressure Relief Valve may be damaged if frozen while containing signiﬁ cant amounts of

water. Such damage may be diﬃ cult to detect visually and can lead to possible injury or death.

Any time the Pressure Relief Valve is subject to possible damage due to freezing, it must be

hydrostatically tested by qualiﬁ ed personnel before being considered safe for use.

LDH valved appliances may be equipped with a pressure relief valve that can be set to any pressure between 90 and 300 psi. Its

function is to protect the pump and supply hose from excess pressure.

See LIA-202 Pressure Relief Valve Instructions for Safe Operation and Maintenance.

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

5.3.1 SETTING RELIEF VALVE PRESSURE

To set the relief valve pressure turn the adjusting screw on the

relief valve housing until the surface of the screw is even with the

desired pressure. A 9/16” (14mm) socket or a 1/4” Allen wrench

may be used to turn the adjusting screw. The Pressure relief

valve should not be disabled (IE: capped, plugged, or set to the

OFF position) for normal service conditions. Disabling the relief

valve may result in system damage or hose rupture if the system

exceeds operating limits. The pressure relief valve meets the

requirements of NFPA 1901.

Adjusting

Screw

Figure 7.1

Pressure Relief Valve

5.4 PRESSURE LOSS

0.5

1.5

0 1000 2000 3000 4000 5000 6000 7000

0 200 400 600 800 1000 1200 1400 1600 1800 2000

LOSS (BAR)

FLOW (LPM)

LOSS (PSI)

FLOW (GPM)

LDH Waterway

With Suction Screen

LDH

Waterway

Figure 5.4

Pressure Loss Chart

5.5 SUCTION SCREEN

This device may be equipped with a suction screen to catch debris larger than 3/8” diameter in the waterway. To add or replace a

suction screen, order TFT part #A1410-KIT for the 4.5” waterway, and TFT part #A1411-KIT for the 5.0” waterway. See Section 5.4

for suction screen pressure loss.

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

6.0 EXPLODED VIEWS AND PARTS LISTS

6.1 BALL INTAKE VALVE - EXPLODED VIEW AND PARTS LIST

SIDE B

COUPLING/

SPOUT

68A

21 22 23 24 25 22 26 27 28 29

10 11

12345

INDEX DESCRIPTION QTY PART #

1GASKET - 6.0" 1V3240

GASKET - 5.0" V3220

2COUPLING RL 6.0"NHF X PSF7.0-NFS 1A4674NX

COUPLING RL 5.0"NHF X PSF7.0-NFS A4671NT

3 PLASTIC STRIP 7.00" 1 A1290

4 RETAINING RING 1 A1521A

5 VALVE SEAT 1 A1520

6 HALF BALL 5.5" ALUM NO DRAIN 1 A1043A

7 BUSHING 1 A2095

8 BODY LOW PROFILE 1 A1016

9 LOWER TRUNNION 1 AY357

10 O-RING-115 1 VO-115

11 1/4-20 X 1/2 SOCKET SET SCREW 1 VT25-20SS500

12 O-RING-135 1 VO-135

13 RETAINING RING 15MM EXTERNAL 1 VR4275

14 THRUST WASHER/SMALL BUSHING 1 A1536

15 12 DP WORM 1 X220

16 THRUST WASHER/LARGE BUSHING 1 A1537

17 KEY 1 X225

18 CRANK SHAFT 1 A1533

19 1/4-20 X 1/2 BUTTON HEAD SCREW 2 VT25-20BH500

20 CRANK WITH KNOB SUBASSEMBLY 1 A1623

21 O-RING-128 1 VO-128

22 BUSHING 2 A1538

23 O-RING-214 1 VO-214

24 INTEGRAL WORM GEAR AND TRUNNION 1 A1504

25 INDICATOR LABEL 1 A1508

26 GEARBOX COVER 1 A1507

27 MODEL NUMBER LABEL 1 A1303

28 LABEL LOW PROFILE BIV 1 A1315

29 1/4-20 X 3/4 SOCKET HEAD SCREW 4 VT25-20SH750

A DRAIN VALVE SUBASSEMBLY 1 SEE SECTION 6.3

B PRESSURE RELIEF VALVE SUBASSEMBLY 1 A1758

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

6.2 SIDE B OPTIONS EXPLODED VIEWS AND PARTS LISTS

124

3MALE HOSE THREADS

INDEX DESCRIPTION QTY 4.0" 4.5" 5.0" 6.0"

1 PLASTIC STRIP 1 A1291 A1291 A1291 A1291

2 CUP SEAL 1 A1596 A1596 A1596 A1596

3 LOCK-OUT SCREW 1 A1294 A1294 A1294 A1294

4 SPOUT 1 A4620N A4625N A4630N A4635N

FEMALE HOSE THREADS ROCKER LUG

INDEX DESCRIPTION QTY 3.5" 4.0" 4.5" 5.0" 6.0"

5 PLASTIC STRIP 1 A1292 A1291 A1291 A1291 A1290

6 CUP SEAL/O-RING 1 A1597 A1596 A1596 A1596 -

7 COUPLING 1 A4665N A4660N A4665N A4670N A4674NX

8 GASKET 1 V3196 V3198 V3210 V3220 V3240

- NFS RING/O-RING 1 -----

- MATE 1 A4730 - - - A4730

- PLASTIC STRIP 1 A1291 - - - A1291

- CUP SEAL 1 A1596 - - - A1596

- BALL 1 VB.437 ----

12 STORZ

INDEX DESCRIPTION QTY 4.0" 5.0" 6.0"

12 PLASTIC STRIP 1 A1292 A1291 A1291

13 CUP SEAL 1 A1597 A1596 A1596

14 LOCK-OUT SCREW 1 A1294 A1294 VB.437

15 COUPLING 1 A4124 A4125 A4289

- MATE 1 A4730 - -

- PLASTIC STRIP 1 A1291 - -

- CUP SEAL 1 A1596 - -

- BALL 1 VB.437 - -

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

7.0 TROUBLE SHOOTING

SYMPTOM POSSIBLE CAUSE REMEDY

Leaks Debris or damage in seal area Clean out debris

If it is not debris it will need to be returned

for service

6.3 AIR VENT/DRAIN [A] EXPLODED VIEW AND PARTS LIST

456758

Replacement Kit - A1621-KIT

ITEM DESCRIPTION QTY PART #

1 1/2" BARB X 1/4"NPTM NIPPLE 1 XX329

2 FOLLOWER 1 U251

3 3/8-24 X 3/8 DOG POINT 1 H515

4 DRAIN HOUSING 1 A1543

5 O-RING 115 2 VO-115

6 DRAIN SLEEVE 1 A1541

7 O-RING-110 1 VO-110

8 DRAIN LEVER 1 A1542

©Copyright Task Force Tips LLC 2016-2018 LIA-212 March 6, 2018 Rev04

8.0 WARRANTY

Task Force Tips LLC, 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA (“TFT”) warrants to the original purchaser of its

Low Proﬁ le Ball Intake Valve (“equipment”), and to anyone to whom it is transferred, that the Low Proﬁ le Intake Valve series includes

a 5 year warranty against manufacturing defects and corrosion aﬀ ecting the valve’s operational performance.

TFT’s obligation under this warranty is speciﬁ cally limited to replacing or repairing the equipment (or its parts) which are shown by

TFT’s examination to be in a defective condition attributable to TFT. To qualify for this limited warranty, the claimant must return the

equipment to TFT, at 3701 Innovation Way, Valparaiso, Indiana 46383-9327 USA, within a reasonable time after discovery of the

defect. TFT will examine the equipment. If TFT determines that there is a defect attributable to it, TFT will correct the problem within

a reasonable time. If the equipment is covered by this limited warranty, TFT will assume the expenses of repair.

If any defect attributable to TFT under this limited warranty cannot be reasonably cured by repair or replacement, TFT may elect to

refund the purchase price of the equipment, less reasonable depreciation, in complete discharge of its obligations under this limited

warranty. If TFT makes this election, claimant shall return the equipment to TFT free and clear of any liens and encumbrances.

This is a limited warranty. The original purchaser of the equipment, any person to whom it is transferred, and any person who is

an intended or unintended beneﬁ ciary of the equipment, shall not be entitled to recover from TFT any consequential or incidental

damages for injury to person and/or property resulting from any defective equipment manufactured or assembled by TFT. It is agreed

and understood that the price stated for the equipment is in part consideration for limiting TFT’s liability. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

TFT shall have no obligation under this limited warranty if the equipment is, or has been, misused or neglected (including failure to

provide reasonable maintenance) or if there have been accidents to the equipment or if it has been repaired or altered by someone

else.

THIS IS A LIMITED EXPRESS WARRANTY ONLY. TFT EXPRESSLY DISCLAIMS WITH RESPECT TO THE EQUIPMENT ALL

IMPLIED WARRANTIES OF MERCHANTABILITY AND ALL IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE.

THERE IS NO WARRANTY OF ANY NATURE MADE BY TFT BEYOND THAT STATED IN THIS DOCUMENT.

This limited warranty gives you speciﬁ c legal rights, and you may also have other rights which vary from state to state.

9.0 MAINTENANCE

TFT appliances are designed and manufactured to be damage resistant and require minimal maintenance. However, as the primary

ﬁ reﬁ ghting tool upon which your life depends, it should be treated accordingly. Do not drop or throw equipment.

This valve should be disconnected, cleaned and visually inspected inside and out at least quarterly for proper function per NFPA

1962 section 8.2, or as water quality and use may require. Moving parts such as handles, valve ball and couplings should be checked

for smooth and free operation. Seals shall be greased as needed with a silicone-based grease such as Dow Corning 112. Any

scrapes that expose bare aluminum should be cleaned and touched up with enamel paint such as Rust-Oleum. Replace any missing

or damaged parts before returning to service. Any repaired device must be tested before being placed in service.

9.1 SERVICE TESTING

In accordance with NFPA 1962 (2013), appliances must be tested a minimum of annually. Appliances failing any part of this test must

be removed from service, repaired and retested upon completion of the repair.

9.1.1 HYDRAULIC TEST

1. The appliance being tested shall be positioned in a protective device or cover capable of holding the appliance and tested to

a minimum hydrostatic pressure of 300 psi (20.7 bar or 2070 kPa).

2. Test caps capable of withstanding the required hydrostatic pressure shall be attached to openings, and a device capable of

exerting the required hydrostatic pressure shall be attached to the appliance.

3. Appliances with relief valves shall have the relief valve outlet blanked oﬀ or otherwise closed during the test.

4. All air shall be bled from the system.

5. The gauge pressure shall be increased by 50 psi (3.45 bar or 345 kPa) increments and held for 30 seconds at each pressure

up to the maximum pressure for which the appliance is being tested and held for 1 minute without leakage.

9.1.2 RELIEF VALVE TEST

1. Hydrostatic testing of the appliance shall be conducted prior to testing the relief valve.

2. The relief valve shall be tested separately from any device it is connected to.

3. The relief valve shall be set to its lowest setting and pressurized.

4. If the relief valve does not operate at or below a pressure 10 percent over the setting, the test shall be discontinued and the

relief valve repaired or replaced.

5. A calibrated test gauge shall be used to verify the setting.

6. After successful completion of the relief valve test, the relief valve shall be reset to the pressure designated by the authority

having jurisdiction.

7. The ﬁ nal setting of the relief valve shall be conﬁ rmed by pressure testing.

9.1.3 SHUTOFF VALVE TEST

1. If the appliance has a shutoﬀ valve, the intake side of the shutoﬀ valve shall be hydrostatically pressurized to the maximum

working pressure of the appliance with the valve in the shutoﬀ position.

2. There shall be no leakage through the valve.

3. A water ﬂ ow through the ﬁ re hose appliance at 100 psi (6.9 bar or 690 kPa) shall be established.

4. The valve shall be closed and reopened twice and shall operate smoothly without evidence of binding or other problems.

9.1.4 RECORDS

A record of testing and repairs must be maintained from the time the appliance is purchased until it is discarded. Each TFT appliance

is engraved with a unique serial number which, if so desired, can be used to identify appliance for documentation purposes.

The following information, if applicable, must be included on the test record for each appliance:

1. Assigned identiﬁ cation number

2. Manufacturer

3. Product or model designation

4. Vendor

5. Warranty

6. Hose connection size

7. Maximum operating pressure

8. Flow rate or range

9. Date received and date put in service

10. Date of each service test and service test results

11. Damage and repairs, including who made the repairs and the cost of repair parts

12. Reason removed from service

9.2 CRANKSHAFT OVERRIDE AND REPLACEMENT

The crankshaft includes an intentional shear joint to protect the gear train from overload, costly repairs, and loss of service. The

magnitude of torque required to shear the crankshaft is several times greater than the torque typically needed to operate the valve at

maximum operating pressure. If the crankshaft breaks during use, this is an indication that either there is something obstructing the

half ball internally or the crank shaft has been abused (e.g. used as a step for climbing).

9.2.1 CRANKSHAFT OVERRIDE

In an emergency, the opposite side of the crankshaft can be turned using a 1/2” wrench or hex socket. This allows the valve to be

open or closed until the crankshaft is replaced. To prevent loss of the 1/8” square key on the crankshaft, do not allow the crankshaft

to slideout of gearbox until a replacement crankshaft is acquired. It is important not to rely on this as a long-term method of operation.

9.2.2 DIAGNOSIS

To diagnose the problem that caused the crankshaft to fail, complete the following steps:

1. Close upstream water supply. If possible, relieve pressure leading up to valve.

2. Locate 1/2” hex where crankshaft protrudes from opposite side of gearbox.

3. Gently turn crank shaft away from travel stop using a ½” hex wrench. Do not attempt to shock crankshaft free and do not

exceed 45 ft-lb (61 Nm) of torque.

4. If crankshaft will not rotate, then half ball is likely obstructed. Only after relieving pressure on ﬂ anged joint, unbolt valve. Clear

any obstructions and evaluate whether repair is needed before returning to service.

5. If crankshaft is able to rotate, cycle the valve several times from open to closed to determine whether the crankshaft binds

at any place between the travel stops. If crankshaft binds, consult Task Force Tips Service Department to determine the

appropriate repairs.

6. If crankshaft rotates freely after clearing any obstructions, then a replacement crank shaft may be ordered from Task Force

Tips and replaced as described below.

9.2.3 CRANKSHAFT REPLACEMENT

A broken crankshaft can be replaced at any time by completing the following steps, regardless of whether or not the upstream water

supply is pressurized. Referring to index numbers shown in section 6.3, follow the steps below:

1. Remove external retaining ring (index 13) adjacent to ½” hex on crank shaft. Do not over-expand the retaining ring.

2. Using a punch or Phillips head screwdriver at least 6” in length, gently push on dimple in ½” hex end of crankshaft (index 18).

Continue to push crankshaft through until it protrudes from opposite side of gearbox.

3. Grab broken end of crankshaft and pull out of gearbox. As crankshaft is withdrawn, grasp small key (index 17) on shaft so it

does not get lost.

4. If 1/8” square x 1” long key is not visible in shaft, it has likely fallen into gearbox bore and must be removed before installing

new crankshaft. If square key is visible in gearbox bore, slide it out of bore. Needle-nose pliers may be helpful depending on

position of key in bore.

5. Verify polymer bushings/thrust washers (index 16 and 14) are still seated in bores on each side of gearbox. If not, locate and

replace bushings.

6. Look through gearbox bore and note approximate orientation of square keyway in worm (index 15). Verify round notch in

polymer bushings/thrust washers (index 16) is aligned with square keyway in worm.

7. Prepare new crankshaft by applying small dab of grease to keyway and seating 1/8” square x 1” long key into keyway. Grease

will keep key in place during assembly.

8. Slide shaft into gearbox with key orientation the same as keyway in worm. Rotate shaft slightly in alternating directions until

key ﬁ nds keyway, then push shaft in until it stops. Retaining ring groove and ½” hex should be protruding through opposite

side of gearbox. If hex is not visible, it may be necessary to slide polymer bushing back into gearbox bore.

9. Install retaining ring (index 13) onto shaft. Do not over-expand the retaining ring.

10.0 REPAIR

Factory service is available with repair time seldom exceeding one day in our facility. Factory serviced appliances are repaired by

experienced technicians to original speciﬁ cations, fully tested and promptly returned. Repair charges for non-warranty items are

minimal. Any returns should include a note as to the nature of the problem and whom to reach in case of questions.

Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability

for damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.com for

parts lists, exploded views, test procedures and troubleshooting guides.

For additional information on care, maintenance and testing, refer to: NFPA 1962: Standard for the Care, Use, Inspection,

Service Testing, and Replacement of Fire Hose, Couplings, Nozzles, and Fire Hose Appliances, 2013 Edition

CAUTION Any alterations to the device and its markings could diminish safety and constitute a misuse of

this product.

11.0 ANSWERS TO YOUR QUESTIONS

We appreciate the opportunity of serving you and making your job easier. If you have any problems or questions, our toll-free

“Hydraulics Hotline”, 800-348-2686, is normally available to you 24 hours a day, 7 days a week.

TASK FORCE TIPS, INC.

MADE IN USA • tft.com 3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

12.0 INSPECTION CHECKLIST

BEFORE EACH USE,

• Fire hoses must be securely attached to appliances.

• Appliances must also be inspected to the following checklist.

BEFORE BEING PLACED BACK IN SERVICE,

1. All valves open and close smoothly and fully.

2. The waterway is clear of obstructions.

3. There is no damage to any thread or other type connection.

4. The pressure setting of the relief valve, if any, is set correctly.

5. All locks and hold-down devices work properly.

6. Internal gaskets are in accordance with NFPA 1962 (2013) Section 7.2.

7. There is no damage to the appliance (e.g., dents, cracks, corrosion, or other defects that could impair operation).

8. All swiveling connections rotate freely.

9. There are no missing parts or components.

10. The marking for maximum operating pressure is visible.

11. There are no missing, broken, or worn lugs on couplings.

NFPA 1962: Standard for the care, use, inspection, service testing, and replacement of ﬁ re hose, couplings, nozzles and ﬁ re hose appliances. (2013 ed., Section 6.2.1).

Quincy, MA: National Fire Protection Agency.

WARNING Any appliance failing any part of the inspection checklist is unsafe and must have the problem

corrected before use. Operating an appliance that fails any of the above inspections is a misuse

of this equipment.

Task Force Tips ABD3SP-NT Operating instructions

Task Force Tips ABD3SP-NT Operating instructions

Task Force Tips ABD3SP-NT Operating instructions

Related papers

Other documents