Motorola Avigilon H5A-DO1-IR Owner's manual



Installation Guide

Avigilon H5A Dome Camera Models:

H5A-D1 H5A-D1-IR H5A-D2

H5A-DC1 H5A-DC1-IR H5A-DC2

H5A-DO1 H5A-DO1-IR H5A-DO2

H5A-DP1 H5A-DP1-IR H5A-DP2

Legal Notices

CENTER, and ACC are trademarks of Avigilon Corporation. Other names or logos mentioned herein may be

the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each

trademark in this document or at all is not a disclaimer of ownership of the related trademark. Avigilon

Corporation protects its innovations with patents issued in the United States of America and other

jurisdictions worldwide (see avigilon.com/patents). Unless stated explicitly and in writing, no license is

granted with respect to any copyright, industrial design, trademark, patent or other intellectual property

rights of Avigilon Corporation or its licensors.

Disclaimer

This document has been compiled and published using product descriptions and specifications available at

the time of publication. The contents of this document and the specifications of the products discussed

herein are subject to change without notice. Avigilon Corporation reserves the right to make any such

changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the

completeness or accuracy of the information contained in this document; or (2) is responsible for your use

of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages

(including consequential damages) caused by reliance on the information presented herein.

Avigilon Corporation

avigilon.com

PDF-H5ADO-A

Revision: 1 - EN

20190904

ii

Important Safety Information

This manual provides installation and operation information and precautions for the use of this device.

Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual

carefully. Please provide this manual to the owner of the equipment for future reference.

This Warning symbol indicates the presence of dangerous voltage within and outside the product

enclosure that may result in a risk of electric shock, serious injury or death to persons if proper

precautions are not followed.



This Caution symbol alerts the user to the presence of hazards that may cause minor or moderate

injury to persons, damage to property or damage to the product itself if proper precautions are not

followed.

WARNING — Failure to observe the following instructions may result in severe injury or death.

l Installation must be performed by qualified personnel only, and must conform to all local codes.

l This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or

“Limited Power Source” with output rated 12 VDC or 24 VAC, 13 W min. or Power over Ethernet (PoE),

rated 48 VDC, 13 W min.

l H5A-D and H5A-DC models are for indoor use only:

l Do not use near water or expose to dripping or splashing.

l Do not place objects filled with liquids above the device.

l Do not expose to rain or moisture.

l Any external power supply connected to this product may only be connected to another Avigilon

product of the same model series. External power connections must be properly insulated.

l Do not connect directly to mains power for any reason.

CAUTION — Failure to observe the following instructions may result in injury to persons or damage

to the device.

l Do not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may

cause permanent damage to the image sensor.

l Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.

l Do not subject the device cables to excessive stress, heavy loads or pinching.

l Do not open or disassemble the device. There are no user serviceable parts.

l Refer all device servicing to qualified personnel. Servicing may be required when the device has

been damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture,

does not operate normally, or has been dropped.

l Do not use strong or abrasive detergents when cleaning the device body.

l Use only accessories recommended by Avigilon.

iii

Regulatory Notices

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

l Reorient or relocate the receiving antenna.

l Increase the separation between the equipment and the receiver.

l Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

l Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or

parties authorized by Avigilon Corporation could void the user’s authority to operate this equipment.

Disposal and Recycling Information

When this product has reached the end of its useful life, please dispose of it according to your local

environmental laws and guidelines.

Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.

European Union:

This symbol means that according to local laws and regulations your product should be disposed of

separately from household waste. When this product reaches its end of life, take it to a collection point

designated by local authorities. Some collection points accept products for free. The separate collection

and recycling of your product at the time of disposal will help conserve natural resources and ensure that it

is recycled in a manner that protects human health and the environment.

iv

Table of Contents

Overview 1

Rear View 1

Front View 2

IR View 3

H5A-D Indoor Dome — Surface Mount 4

Cover View 4

Bottom View 5

Wall Plate View 6

Base View 7

H5A-DC Indoor Dome — In-Ceiling Mount 8

Cover View 8

Clamp View 9

Top View 10

H5A-DO Outdoor Dome — Surface Mount 11

Cover View 11

Top View 12

Wall Plate View 13

H5A-DP Outdoor Dome — Pendant Mount 14

Cover View 14

Top View 15

Bottom View 16

Pendant Wall Mount Bracket View 17

Pendant Wall Mount View 18

Pendant NPT Mount View 19

Preparing the Installation 20

Removing the Dome Cover 20

Mounting and Aiming Video Analytics Cameras 20

Inserting Cables through the Sealing Grommet 20

Indoor Surface Mount Installation 22

Required Tools and Materials 22

Camera Package Contents 22

Installation Steps 22

Mounting the Dome Camera Using the Bottom Cable Entry Hole 22

Mounting the Dome Camera Using the Side Cable Entry Hole 23

Mounting the Dome Camera to an Electrical Box 23

v

Connecting Cables 24

Installing the Dome Cover 25

In-Ceiling Mount Installation 27

Required Tools and Materials 27

Camera Package Contents 27

Installation Steps 27

Mounting the Dome Camera Using the Ceiling Clamps 27

Mounting the Dome Camera using the Camera Mounting Holes 29

Connecting Cables 30

Installing the Dome Cover 31

Outdoor Surface Mount Installation 32

Required Tools and Materials 32

Camera Package Contents 32

Installation Steps 32

Mounting the Dome Camera Using the Bottom Cable Entry Hole 32

Mounting the Dome Camera Using the Side Cable Entry Hole 33

Mounting the Dome Camera to an Electrical Box 36

Connecting Cables 37

Installing the Dome Cover 38

Pendant Mount Installation 39

Required Tools and Materials 39

Package Contents 39

Installation Steps 39

Mounting the Dome Camera to the Pendant Wall Mount 40

(Optional) Mounting the Dome Camera to the Pendant NPT Mount 44

Connecting Cables 47

Installing the Dome Cover 47

Connecting to the Camera 49

(Optional) Using the USB Wi-Fi Adapter 49

Assigning an IP Address 49

Accessing the Live VideoStream 50

Aiming the Dome Camera 50

(Optional) Configuring microSD Card Storage 50

Zooming and Focusing the DomeCamera 50

Configuring the Camera 51

For More Information 51

vi

Cable Connections 52

Connecting External Power 52

Connecting to External Devices 52

Connecting to Microphones, Speakers, and Video Monitors 53

Connection Status LED Indicator 55

Resetting to Factory Default Settings 56

Setting the IP Address Using the ARP/Ping Method 57

Cleaning 58

Dome Bubble 58

Body 58

Limited Warranty and Technical Support 59

vii

Overview

Rear View

1.

Azimuth control

Provides control of the image angle.

2.

I/O connector block

Provides connections to external input/output devices.

3.

Micro USB port

Accepts a micro USB to USB adapter. Only required when using the Avigilon USB Wi-Fi Adapter.

4.

microSD card slot

Accepts a microSD card for onboard storage. For more information, see (Optional) Configuring

microSD Card Storage on page50.

Overview 1

Front View

1.

Power connector block

Accepts a terminal block with either an AC or DC power connection. DC input can be either polarity.

Only required when Power over Ethernet is not available.

2.

Ethernet port

Accepts an Ethernet connection to a network. Server communication and image data transmission

occurs over this connection. Also receives power when it is connected to a network that provides

Power over Ethernet.

3.

Serial number tag

Device information, product serial number and part number label.

4.

Audio/video connector

Accepts a mini-jack connector (3.5 mm).

5.

Pan lock thumb screw

Provides a locking mechanism for the image pan adjustment.

6.

Tilt lock thumb screw

Provides a locking mechanism for the image tilt adjustment.

Front View 2

IR View

1.

IR Illuminator Ring

Provides scene illumination in the IR spectrum. The IR illuminator ring is not included with all models.

2.

Link LED indicator

Indicates if there is an active connection in the Ethernet port.

3.

Connection status LED indicator

Provides information about device operation. For more information, see Connection Status LED

Indicator on page55.

IR View 3

H5A-D Indoor Dome — Surface Mount

Cover View

1.

Dome cover

Vandal resistant dome cover.

2.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

3.

Sidewall plug

Covers the side cable entry hole.

H5A-D Indoor Dome — Surface Mount 4

Bottom View

1.

Cable entry hole

An entry hole for the cables required for camera operation.

2.

Mounting holes

Mounting points for the camera.

3.

Wall plate mounting screws

Screws to attach the camera to the wall plate.

Bottom View 5

Wall Plate View

1.

Leveling edge

Flat edge for aligning the wall plate to an electrical box.

2.

Wall plate mounting points

Points for mounting the camera to the wall plate

3.

Electrical box mounting holes

Holes for mounting the wall plate to an electrical box. The wall plate supports four configurations:

A. UK standard single gang box

B. Octagon gang box

C. 4" gang box

D. US standard single gang box

Wall Plate View 6

Base View

1.

Lanyard

Connects to a lanyard hook on the cover.

Base View 7

H5A-DC Indoor Dome — In-Ceiling Mount

Cover View

1.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

2.

Dome cover

Vandal resistant dome cover.

H5A-DC Indoor Dome — In-Ceiling Mount 8

Clamp View

1.

Clamps

Spring loaded locking mechanisms that secure the camera to the mounting surface.

Clamp View 9

Top View

1.

Lanyard

Connects to a lanyard hook on the cover.

2.

Cable entry hole

An entry hole for the cables required for camera operation.

3.

Mounting holes

Holes for mounting the camera to a mounting surface.

Top View 10

H5A-DO Outdoor Dome — Surface Mount

Cover View

1.

Dome cover

Vandal resistant dome cover.

2.

Tamper resistant screws

Star-shaped captive screws to fix the dome cover to the base.

3. Side cable entry cover

Covers the side cable entry hole.

H5A-DO Outdoor Dome — Surface Mount 11

Top View

1.

Wall plate mounting screws

Screws for mounting the camera to the wall plate.

2.

Lanyard

Connects to a lanyard hook on the cover.

3.

Bottom cable entry hole

A bottom entry hole for the cables required for camera operation.

4.

Side cable entry hole

A side entry hole for the cables required for camera operation.

Top View 12

Wall Plate View

1.

Camera mounts

Points for mounting the camera body to the wall plate.

2.

Cable entry hole

An entry hole for the cables required for camera operation.

3.

Mounting holes

Holes for mounting the wall plate to the following:

A. UK standard single gang box

B. Octagon gang box

C. 4" gang box

D. Mounting surface

E. US standard single gang box

Wall Plate View 13

Page is loading ...

Motorola Avigilon H5A-DO1-IR Owner's manual

Motorola Avigilon H5A-DO1-IR Owner's manual

Related papers

Other documents