Halo RL460WH827PK Installation guide

Halo
Brand
Halo
Model
RL460WH827PK
Type
Installation guide
Instruction Manual/Instrucciones/Directives
Questions?/¿Preguntas?/Questions ? 1-800-334-6871 [email protected]
1
HALO
®
UL Listed
- HALO
®
: H99ICAT, H99RTAT, H99TAT, H995ICAT, H995RICAT
- ALL-PRO
™
: ET400ATSB, EI400ATSB
UL Classified
- Utilitech: CR04ICAT
- Thomas: PS4
- Lithonia: L3, L3R
DIMMING
• The HALO
®
LED luminaire can be dimmed with many standard dimmers; however,
a LED-rated dimmer or an electronic low voltage version of a standard dimmer (with
neutral connection) is recommended for many applications. Updates in dimmer
technology and special conditions may apply depending on the dimmer type being
used. To be assured of the latest information regarding luminaire and dimmer
compatibility, please contact dimmer manufacturer.
GROUND WIRE INSTALLATION
NOTE: Ground wire must be securely installed to the
housing. Three connection methods shown below.
1. For ground connection from LED module to housing,
use provided green ground wire (factory installed)
as shown in (Fig. 1).
2. Connect other end of ground wire to housing.
Connection to housing may vary depending
on model. Three connection methods are
described below.
• Use existing screw inside housing (Fig. 2).
ITEMS REQUIRED
(Purchase separately)
• Screwdriver
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• HALO
®
recessed luminaires (fixtures) are designed to meet the latest NEC
requirements and are UL/cUL listed in full compliance with UL 1598. Before
attempting installation of any recessed lighting luminaire check your local
electrical code. This code sets the wiring standards for your locality and should
be carefully studied before starting.
• Read and follow these instructions.
• Risk of fire. MINIMUM 90° C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
• Risk of electric shock. To avoid possible electrical shock, be sure that power supply is
turned off at fuse box or circuit breaker before installing or servicing fixture.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
SAVE THESE INSTRUCTIONS AND WARNINGS.
HOUSINGS
• The RL406830WH comes with a dedicated LED connector for California Title 24
Compliance and is UL Listed for installation into Halo
®
#995X series recessed
LED housings.
• The RL406830WH also includes an E26 Edison screw base adapter to accommodate
standard screw base ICAT housings. The RL406830WH is UL Listed and Classified for
retrofit in the following housings:
ENGLISH
A. LED module
Módulo LED
Module DEL
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE/CONTENU DU PAQUET
RL406830WH
RL406830WH-C
WARNING
Fig. 1
A
Ground wire
Fig. 2
#1
#2
#3
Ceiling thickness
adjustment slot
(one of three slots
inside housing)
Ground
wire
(View from inside the housing)
B. #8 Self-drilling sheet metal screw
Tornillo para plancha de metal
autoperforante n.°8
Vis à métal autotaraudeuse no 8
C. #8-32 Machine screw
Tornillo mecánico #8-32
Vis de mécanique #8-32
D. #8-32 Hex nut
Tuerca hexagonal #8-32
Écrou hexagonal #8-32
E. Foam Gasket
Junta de goma espuma
Bague d’étanchéité
2
been supplied, installed, and/or used in conjunction with Cooper Lighting products. Damage to
the product caused by replacement bulbs or corrosion or discoloration of brass components
are not covered by this warranty.
LIMITATION OF LIABILITY:
IN NO EVENT SHALL COOPER LIGHTING BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN
CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS;
NOR SHALL THE LIABILITY OF COOPER LIGHTING FOR ANY CLAIMS OR DAMAGE ARISING
OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE,
MAINTENANCE, REPAIR OR MODIFICATION OF COOPER LIGHTING PRODUCTS, OR SUPPLY OF
ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF COOPER LIGHTING
PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR
INSTALL FIXTURES.
To obtain warranty service, please contact Cooper Lighting, LLC, at 1-800-334-6871, press
option 2 for Customer Service, or via e-mail [email protected] and
include the following information:
• Name, address and telephone number
• Date and place of purchase
• Catalog and quantity purchase
• Detailed description of problem
All returned products must be accompanied by a Return Goods Authorization Number issued
by the Company and must be returned freight prepaid. Any product received without a Return
Goods Authorization Number from the Company will be refused.
Cooper Lighting, LLC is not responsible for merchandise damaged in transit. Repaired or
replaced products shall be subject to the terms of this warranty and are inspected when
packed. Evident or concealed damage that is made in transit should be reported at once to
the carrier making the delivery and a claim filed with them.
Reproductions of this document without prior written approval of Cooper Lighting, LLC are strictly prohibited.
For assistance, call 1-800-334-6871 or e-mail us at [email protected].
Printed in China
ARTÍCULOS NECESARIOS
(se compran por separado)
• Destornillador
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Al utilizar el producto, siempre se deben seguir las precauciones básicas, incluído
lo siguiente:
• Tenga en cuenta todas las advertencias, incluyendo las advertencias a continuación
Y aquellas incluidas en el producto.
• La luminarias (accesorios) empotradas HALO
®
están diseñadas para cumplir con
los requisitos NEC más recientes y están catalogadas por UL/cUL en completo
cumplimiento con UL 1598. Antes de comenzar la instalación de su luminaria
empotrada verifique el código local. Este código fija los estándares de cableados
de su localidad y debe ser estudiado cuidadosamente antes de comenzar.
• Lea y siga estas instrucciones.
• Riesgo de incendio. UTILICE CONDUCTORES DE SUMINISTRO QUE SOPORTEN UN
MÍNIMO DE 90°C. Si no está seguro consulte a un electricista.
• Riesgo de descarga eléctrica. Para evitar una descarga eléctrica, asegúrese que el
suministro eléctrico esté desconectado en la caja de fusibles o interruptores de
circuito antes de instalar o dar mantenimiento al accesorio.
PRECAUCIÓN
• Conecte el accesorio a una fuente de energía de 120 Voltios, 60 Hz. Cualquier
otro tipo de conexión anula la garantía.
• El accesorio debe ser instalado por personas con experiencia en cableado
doméstico o por un electricista calificado. El sistema eléctricoy el método de
conexión eléctrica del accesorio debe cumplir con el Código eléctrico nacional
y los códigos locales sobre edificios.
• Este dispositivo cumple con parte 15 de las reglas de FFC. SU operación está sujeta
a las siguiente condiciones: (1) Este dispositivo no puede causar interferencia dañina,
y (2) este dispositivo puede recibir interferencia, incluyendo aquella que puede causar
una operación no deseada del dispositivo.
GUARDE ESTAS INSTRUCCIONES Y ADVERTENCIAS.
ALOJAMIENTOS
• EL RL406830WH viene con un Conector LED especial para el Cumplimiento del Titulo
24 de California y está homologado por UL para la instalación en alojamientos de LED
Halo
®
empotrados saeries.
• EL RL406830WH también incluye un adaptador de base Edison para adaptar
alojamientos ICAT de base con rosca estándar. El RL406830WH está homologado y
clasificado por UL para adaptarse en los siguientes alojamientos.
• Use supplied #8 nut on existing stud (Fig. 3).
• Use supplied #8 screw (B) in existing hole (Fig. 4).
RETROFIT INSTALLATION INTO E26 EDISON
SCREW BASE RECESSED HOUSING
NOTE: Confirm housing is compatible with
RL406830WH module. A listing of the most common
housings is provided in the HOUSINGS section of
these instructions.
1. Remove mounting bracket and plate from inside
existing recessed housing (if installed).
2. Remove socket from plate (if installed).
3. Place foam gasket on trim ring flange (Fig. 5)
4. Screw Edison base adapter into existing Edison
base socket in housing (Fig. 5).
5. Squeeze the friction blades together as shown and
install into recessed housing (Fig. 6).
6. Carefully route wires into fixture and push module
up flush to ceiling surface.
INSTALLATION INTO HALO
®
H995X
SERIES LED (non-screw base) HOUSINGS
NOTE: Meets California Title 24 High Efficacy
Compliance.
1. Remove LED connector box. Unplug orange
connector.
2. Place foam gasket on trim ring flange (Fig. 5)
3. Plug module into Halo recessed fixture connector
(Fig. 7).
4. Squeeze friction blades together and install into
recessed housing.
5. Carefully route wires into fixture and push module
up flush to ceiling surface.
REPLACING LED MODULE
1. With fingertips, pull down firmly on trim ring until
module is removed from the housing.
2. Disconnect LED module wiring from recessed can
(LED connector or screw-in Edison base).
3. Remove ground wire from housing.
3-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Cooper Lighting, LLC (“Cooper Lighting”) warrants to customers that, for a period of three
years from the date of purchase, Cooper Lighting’s products will be free from defects in
materials and workmanship. The obligation of Cooper Lighting under this warranty is expressly
limited to the provision of replacement products. This warranty is extended only to the original
purchaser of the product. A purchaser’s receipt or other proof of date of original purchase
acceptable to Cooper Lighting. This is required before warranty performance shall be rendered.
This warranty does not apply to Cooper Lighting products that have been altered or repaired or
that have been subjected to neglect, abuse, misuse or accident (including shipping damages).
This warranty does not apply to products not manufactured by Cooper Lighting which have
Fig. 3
#1
#2
#3
Threaded stud
in side wall of
housing
(View from inside the housing)
#1
#2
#3
#8 Nut
Ground
wire
Fig. 5
E26 Edison
screw base
adapter
LED
connector
box
A
Fig. 7
HALO dedicated
LED connector
A
Fig. 6
Squeeze friction blades
A
Fig. 4
#1
#2
#3
#1
#2
#3
Ground
wire
Existing hole
(View from inside the housing)
B
ESPAÑOL
ADVERTENCIA
Foam gasket
Foam gasket
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Halo RL460WH827PK Installation guide

Halo
Brand
Halo
Model
RL460WH827PK
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents